Display Item List
WARNING: This page is about a different car, the 2005 Nissan Frontier. However, it is still accessible from the selected car via links, so may be relevant.
DATA MONITOR MODE DISPLAY ITEM LIST
| Monitored item (Unit) | Monitor item selection | Remarks | ||||||
| ECU INPUT SIGNALS | MAIN SIGNALS | SELECTION FROM MENU | ||||||
| VHCL/S SEN.FR [km/h] or [mph] | (1) | (2) | (1) | Wheel speed calculated by ABS actuator and electric unit (control unit). Signal input with CAN communication line. |
||||
| VHCL/S SEN.RR [km/h] or [mph] | (1) | (2) | (1) | Wheel speed calculated by TCM. Signal input with CAN communication line. |
||||
| ENGINE SPEED [rpm] | (1) | (2) | (1) | Engine speed is displayed. Signal input with CAN communication line. |
||||
| BATTERY VOLT [V] | (1) | (2) | (1) | Power supply voltage for transfer control unit. | ||||
| 2WD SWITCH [ON/OFF] | (1) | (2) | (1) | 4WD shift switch signal status is displayed. | ||||
| 4H SWITCH [ON/OFF] | (1) | (2) | (1) | |||||
| 4L SWITCH [ON/OFF] | (1) | (2) | (1) | |||||
| 4L POSI SW [ON/OFF] | (1) | (2) | (1) | 4LO switch signal status is displayed. | ||||
| ATP SWITCH [ON/OFF] | (1) | (2) | (1) | ATP switch signal status is displayed. (A/T models) | ||||
| WAIT DETCT SW [ON/OFF] | (1) | (2) | (1) | Wait detection switch signal status is displayed. | ||||
| 4WD MODE [2H/4H/4L] - | (1) | (2) | (1) | Control status of 4WD recognized by transfer control unit. (2WD, 4H or 4LO) | ||||
| VHCL/S COMP [km/h] or [mph] - | (1) | (1) | Vehicle speed recognized by transfer control unit. | |||||
| SHIFT ACT 1 [ON/OFF] | (2) | (1) | (1) | Output condition to actuator motor (clockwise) | ||||
| SHIFT AC MON 1 [ON/OFF] | (2) | (2) | (1) | Check signal for transfer control unit signal output | ||||
| SHIFT ACT 2 [ON/OFF] | (2) | (1) | (1) | Output condition to actuator motor (counterclockwise) | ||||
| SHIFT AC MON 2 [ON/OFF] | (2) | (2) | (1) | Check signal for transfer control unit signal output | ||||
| SFT ACT/R MON [ON/OFF] | (2) | (2) | (1) | Operating condition of actuator motor relay (integrated in transfer control unit) | ||||
| SHIFT POS SW 1 [ON/OFF] | (1) | (2) | (1) | Condition of actuator position switch 1 | ||||
| SHIFT POS SW 2 [ON/OFF] | (1) | (2) | (1) | Condition of actuator position switch 2 | ||||
| SHIFT POS SW 3 [ON/OFF] | (1) | (2) | (1) | Condition of actuator position switch 3 | ||||
| SHIFT POS SW 4 [ON/OFF] | (1) | (2) | (1) | Condition of actuator position switch 4 | ||||
| 4WD FAIL LAMP [ON/OFF] | (2) | (1) | (1) | Control status of 4WD warning lamp is displayed. | ||||
| 2WD IND [ON/OFF] | (2) | (2) | (1) | Control status of 4WD shift indicator lamp (rear) is displayed. | ||||
| 4H IND [ON/OFF] | (2) | (2) | (1) | Control status of 4WD shift indicator lamp (front and center) is displayed. | ||||
| 4L IND [ON/OFF] | (2) | (2) | (1) | Control status of 4LO indicator lamp is displayed. | ||||
| Voltage [V] | (2) | (2) | (1) | The value measured by the voltage probe is displayed. | ||||
| Frequency [Hz] | (2) | (2) | (1) | The value measured by the pulse probe is displayed. | ||||
| DUTY-HI (high) [%] | (2) | (2) | (1) | |||||
| DUTY-LOW (low) [%] | (2) | (2) | (1) | |||||
| PLS WIDTH-HI [msec] | (2) | (2) | (1) | |||||
| WIDTH-LOW [msec] | (2) | (2) | (1) | |||||
|
||||||||