LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2000 >> Sentra CA >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Engine - 1.8L >> Torque Specifications

Torque Specifications

TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
Buffer Rod Bolt 32-40 (43-54)
Buffer Rod Bracket Bolt 32-40 (43-54)
Camshaft Sprocket Bolt
Intake 80-87 (108-118)
Exhaust 72-94 (98-127)
Connecting Rod Nut
1st Step 10-12 (14-16)
2nd Step 35-45 Degrees Or 17-21 (23-28)
Control Rod Bolt 10-13 (14-18)
Crankshaft Pulley Bolt 97-112 (132-152)
Crossmember-To-Engine Mount Bolt 57-72 (77-98)
Cylinder Head Bolt (1)
1-10 (Large Bolt)
1st Step 21 (28)
2nd Step 44 (60)
3rd Step Loosen Bolts Completely
4th Step 21 (28)
5th Step 50-55 Degrees Or 40-47 (54-64)
11-15 (Small Bolt)
6th Step (2)
Exhaust Manifold Nut (3) 19-21 (26-28)
Exhaust Pipe-To-Manifold Nut 21-24 (28-33)
Flexplate Bolt 69-76 (93-103)
Flywheel Bolt 61-69 (83-93)
Front Engine Mount Bolt 45-51 (60-70)
Idler Sprocket Bolt 32-43 (43-58)
Intake Manifold Collector-To-Intake Manifold Bolt (4) 12-15 (16-20)
Intake Manifold Nut (4) 12-15 (16-20)
Intake Manifold Support 12-17 (17-24)
Left Engine Mount Bolt 32-40 (43-54)
Main Bearing Cap Bolt 34-38 (46-52)
Oil Pan Drain Plug 21-29 (28-39)
Oil Pressure Regulator Valve Plug 29-43 (39-58)
Oil Pump Pick-Up Tube Bolt 12-15 (16-20)
Rear Engine Mount Bolt 45-51 (60-70)
Right Engine Mount Bolt 45-51 (60-70)
Support Rod Bolt 26-35 (35-47)
Spark Plug 14-22 (19-30)
Starter Bolt 23-31 (31-42)
INCH Lbs. (N.m) 
Camshaft Journal Cap Bolt (5)
Cylinder Head Cover Bolt 18-35 (2-4)
Cylinder Head Front Cover Bolt/Nut 33-44 (3.7-5)
Front Cover Bolt 56-74 (6.3-8.3)
Lower Timing Chain Tensioner Bolt 56-74 (6.3-8.3)
Oil Pan Bolt 56-74 (6.3-8.3)
Oil Pump Cover Bolt 56-74 (6.3-8.3)
Oil Pump Cover Screw 33-44 (3.7-5)
Upper Timing Chain Tensioner Bolt 56-74 (6.3-8.3)
Water Pump Bolt 56-74 (6.3-8.3)
Water Pump Pulley Bolt 56-74 (6.3-8.3)
(1) Tighten in sequence, large bolts first. See Figure.
(2) Tighten small bolts in sequence to 56-74 INCH lbs. (6.3-8.3 N.m).
(3) Tighten in sequence. See Figure.
(4) Tighten in sequence. See Figure.
(5) See CAMSHAFT  under REMOVAL & INSTALLATION for tightening sequence and torque specifications. See Figure.