Continuously Variable Transaxle (CVT)

• Service Precautions
• General Information
  • Specifications
  • System Configuration
  • Overview
  • Description Of Structure And Operation
    • Sectional View
    • Hydraulic Control System
      • Control Description
    • General Information Regarding The Main Components
    • Shift Mechanism
      • Pulley ratio
    • Line Pressure Control And Secondary Pressure Control
    • Lock-Up Control
    • Select Control
    • Control Elements And Input/Output
      • Notes
      • Fail-Safe Function
    • Protection Control
      • Notes
      • Control during wheel spinning
      • Control at high fluid temperature
      • Torque reduction when the vehicle is reversing
      • Reversing prevention
• Service Specifications
• Lubricants
• Diagnosis
  • Diagnostic Troubleshooting Flow
  • Introduction To CVT Diagnosis
  • CVT Diagnostic Troubleshooting Strategy
  • Diagnostic Function
    • Warning Indicator
    • On-Board Diagnostics
    • How To Connect The Scan Tool (M.U.T.-III)
    • How To Read And Erase Diagnostic Trouble Codes
    • How To Read Data List
    • How To Diagnose The Can Bus Lines
  • Freeze Frame Data Reference Table
    • Notes
    • Freeze Frame Data
  • Initialization Procedure For CVT Learned Value
    • Purpose
    • Initialization Procedure
  • Learning Procedure
    • Notes
    • When Replacing The TCM
    • When Replacing The CVT Assembly
    • When Replacing The Valve Body Assembly
  • Fluid Deterioration Level Erasing Procedure
  • Road Test
  • Torque Converter Stall Test
    • Notes
    • Judgment Of Torque Converter Stall Test Results
  • Hydraulic Pressure Test
  • Ratio Pattern
    • D Range
    • L Range
    • Sport Mode
  • Torque Converter Clutch Operation Zone
  • Diagnostic Trouble Code Chart
  • Diagnostic Trouble Code Procedures
    • DTC P0703: Malfunction of Stoplight Switch
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0705: Malfunction of Transmission Range Switch
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence-Input Other Rationality)
      • LOGIC FLOW CHARTS (Monitor Sequence-Input Open Circuit)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P071B: Malfunction of Ds position switch (stuck ON) ; DTC P071C: Malfunction of Ds position switch (stuck OFF)
      • Diagnostic Function
      • Descriptions Of Monitor Methods <P 71B>
      • Monitor Execution <P 071B>
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC set in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence-Input Rationality-Low) <P 071B>
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern <P 071B>
      • Descriptions Of Monitor Methods <P071C>
      • Monitor Execution <P071C>
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC set in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence-Input Rationality-High) <P071C>
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern <P071C>
      • Probable Causes
    • DTC P0711: Malfunction of Transmission Fluid Temperature Sensor (Abnormality in transmission fluid temperature sensor function)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC set in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0712: Malfunction of Transmission Fluid Temperature Sensor (low input)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0713: Malfunction of the Transmission Fluid Temperature Sensor (high input)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0715: Malfunction of Primary Pulley Speed Sensor
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence-Input Rationality-Low (Open/Low revolution))
      • LOGIC FLOW CHARTS (Monitor Sequence-Input Open Circuit)
      • LOGIC FLOW CHARTS (Monitor Sequence-Input Other Rationality)
      • DTC Set Conditions
        • Check Conditions <Input Rationality-Low (Open/Low revolution)>
        • Check Conditions <Input Open Circuit>
        • Check Conditions <Input Other Rationality>
        • Judgment Criteria <Input Rationality-Low (Open/Low revolution)>
        • Judgment Criteria <Input Open Circuit>
        • Judgment Criteria <Input Other Rationality>
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0720: Malfunction of Secondary Pulley Speed Sensor
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence-Input Rationality-Low (Open/Low revolution))
      • LOGIC FLOW CHARTS (Monitor Sequence-Input Open Circuit)
      • LOGIC FLOW CHARTS (Monitor Sequence-Input Other Rationality)
      • DTC Set Conditions
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0730: Incorrect Gear Ratio
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0741: Abnormality in Lock-up Function
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0776: Abnormality in Secondary Pressure Solenoid Valve Function
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence-Output Functional High)
      • LOGIC FLOW CHARTS (Monitor Sequence-Output Functional Low)
      • DTC Set Conditions
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0815 Malfunction of Paddle Shift UP Switch
      • Diagnostic Function
      • Judgment Criteria
      • Probable Causes
      • Diagnosis
    • DTC P0816: Malfunction of Paddle Shift DOWN Switch
      • Diagnostic Function
      • Judgment Criteria
      • Probable Causes
      • Diagnosis
    • DTC P0842: Malfunction of the Secondary Pressure Sensor (low input)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0843: Malfunction of the Secondary Pressure Sensor (high input)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0847: Malfunction of the Primary Pressure Sensor (low input)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0848: Malfunction of the Primary Pressure Sensor (high input)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P084A: Abnormality in Primary Pressure Sensor Function
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0962: Malfunction of the Line Pressure Solenoid Valve (low input)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0963: Malfunction of the Line Pressure Solenoid Valve (open)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0966: Malfunction of the Secondary Pressure Solenoid Valve (low input)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0967: Malfunction of the Secondary Pressure Solenoid Valve (high input)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0969: Abnormality in Primary Pressure Solenoid Valve Function
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence-Output Functional High)
      • LOGIC FLOW CHARTS (Monitor Sequence-Output Functional Low)
      • DTC Set Conditions
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0970: Malfunction of the Primary Pressure Solenoid Valve (low input)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0971: Malfunction of the Primary Pressure Solenoid Valve (high input)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P1607: Malfunction of the System Power Supply (low voltage)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Diagnosis
    • DTC P1637: Malfunction of Memory Backup
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Condition
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Diagnosis
    • DTC P1773: Malfunction of ABS/ASC
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P1798: Malfunction of G Sensor Signal
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnostic
    • DTC P1799: Malfunction of Brake Fluid Pressure Signal
      • Diagnostic Function
      • Judgment Criteria
      • Probable Causes
      • Diagnostic
    • DTC P2719: Abnormality in Select Pressure Solenoid Valve Function
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence-Output Functional High)
      • LOGIC FLOW CHARTS (Monitor Sequence-Output Functional Low)
      • DTC Set Conditions
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P2720: Malfunction of the Select Pressure Solenoid Valve (low input)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P2721: Malfunction of Select Pressure Solenoid Valve (high input)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P2763: Malfunction of the Lock-up Solenoid Valve (high input)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P2764: Malfunction of the Lock-up Solenoid Valve (low input)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P2765: Malfunction of Turbine Speed Sensor
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence-Input Rationality-Low (Open/Low revolution))
      • LOGIC FLOW CHARTS (Monitor Sequence-Input Open Circuit)
      • LOGIC FLOW CHARTS (Monitor Sequence-Input Other Rationality)
      • DTC Set Conditions
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC U0001: Malfunction of CAN communication circuit (Bus off)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC U0100: CAN time-out error (Engine)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC U0121: CAN time-out error (ABS/ASC)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC U0141: CAN time-out error (ETACS)
      • Notes
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC U0317: CAN time-out error (EPB)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC U1197: Coding data unavailable
      • Diagnostic function
      • Judgment Criteria
      • Probable Causes
      • Diagnosis
    • DTC U1195: Coding not completed
      • Diagnostic function
      • Judgment Criteria
      • Probable Causes
      • Diagnosis
    • DTC U1417: Wrong coding data received
      • Diagnostic function
      • Judgment Criteria
      • Probable Causes
      • Diagnosis
  • Trouble Symptom Diagnosis Chart
  • Data List Reference Table
  • TCM Terminal Voltage Table
  • Oscilloscope Inspection Procedures
    • Notes
    • Wave Pattern Sample
• Diagnosis
  • Troubleshooting Strategy
    • Notes
    • Precautions For Diagnosis
  • Indicator Check
  • Diagnosis Function
    • Notes
    • On-Board Diagnostics
    • How To Connect The Scan Tool (M.U.T.-III)
    • How To Read And Erase Diagnostic Trouble Codes
    • How To Read Data List
    • How To Perform Actuator Test
    • How To Diagnose The Can Bus Lines
  • Freeze Frame Data Reference Table
    • Notes
    • Freeze Frame Data
  • Diagnostic Trouble Code Chart
  • Trouble Symptom Chart
  • Diagnostic Trouble Code Procedures
    • DTC C100A: FL Wheel Speed Sensor System (Faulty Circuit); DTC C1015: FR Wheel Speed Sensor System (Faulty Circuit); DTC C1020: RL Wheel Speed Sensor System (Faulty Circuit); DTC C102B: RR Wheel Speed Sensor System (Faulty Circuit)
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1011: FL Wheel Speed Sensor System (Faulty Signal); DTC C101C: FR Wheel Speed Sensor System (Faulty Signal); DTC C1027: RL Wheel Speed Sensor System (Faulty Signal); DTC C1032: RR Wheel Speed Sensor System (Faulty Signal)
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1014: FL Wheel Speed Sensor System (characteristics abnormality); DTC C101F: FR Wheel Speed Sensor System (characteristics abnormality); DTC C102A: RL Wheel Speed Sensor System (characteristics abnormality); DTC C1035: RR Wheel Speed Sensor System (characteristics abnormality)
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnosis
    • DTC C1078: Tire Turning Malfunction
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1219: Steering Wheel Sensor System (Faulty Signal)
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C121A: Steering Wheel Sensor System (neutral learning abnormality)
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C123C: G and Yaw Rate Sensor System (Lateral G and Yaw Rate Sensor Output Signal)
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1242: G and Yaw Rate Sensor System (Abnormality of Longitudinal G Sensor Output Signal)
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1610: AWC Power Supply Electronic Relay Malfunction
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1613: Drive Mode Selector System (Stuck ON)
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1614: Parking Brake Switch System (Stuck On)
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1615: Brake Control Prohibited Request
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1616: Cranking Signal System (Stuck ON)
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1621: Electronic Control Coupling Solenoid Protection
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1623: Brake Control Abnormality
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1624: AWC-ECU Internal Abnormality
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1626: Actuator Power Supply Voltage Malfunction
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1628: Abnormal Electronic Control Coupling Solenoid Current
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1629: ASC CAN Data (not received)
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1630: Steering Wheel Sensor CAN Data (not received)
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1631: ETACS CAN Data (not received)
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1632: Engine CAN Data (not received)
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1633: Transmission CAN Data (not received)
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C1707: Implausible Coding Data
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C2100: Battery Voltage Malfunction (Low Voltage)
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C2101: Battery Voltage Malfunction (High Voltage)
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC C2205: Steering Wheel Sensor System (Internal Error)
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC U0100: Engine Time-out Error
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC U0101: Transmission Time-out Error
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC U0121: ASC Time-out Error
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC U0126: Steering Wheel Sensor Time-out Error
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC U0141: ETACS Time-out Error
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC U0401: Engine Data Malfunction
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC U0428: Steering Wheel Sensor Data Malfunction
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC U0431: ETACS Data Malfunction
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC U1073: Bus-Off
      • Notes
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC U1195: Coding Not Completed
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC U119A: VIN Mismatch
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC U1425: Transmission Data Malfunction
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC U1426: ASC Data Malfunction
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC U1427: Wheel Speed Sensor Data Malfunction
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
    • DTC U1428: G and Yaw Rate Sensor Data Malfunction
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnosis
  • Symptom Procedures
    • INSPECTION PROCEDURE 1: Communication Between Scan Tool (M.U.T.-III) and AWC-ECU Cannot be Established
      • Comments On Trouble Symptom
      • Probable Causes
      • Diagnosis
    • INSPECTION PROCEDURE 2: Shifting the S-AWC Drive Mode-selector Does not Change the Mode
      • Comments On Trouble Symptom
      • Probable Causes
      • Diagnosis
    • INSPECTION PROCEDURE 3: The Tight Corner Braking Phenomenon* Appears with the S-AWC Drive Mode-selector in the AWC ECO or NORMAL Position
      • Notes
      • Comments On Trouble Symptom
      • Probable Causes
      • Diagnosis
    • INSPECTION PROCEDURE 4: AWD system check screen is displayed on the center of the multi-information display and a "AWD" symbol flashes at the left top. But no diagnostic trouble codes are set
      • Comments On Trouble Symptom
      • Probable Causes
      • Diagnosis
    • INSPECTION PROCEDURE 5: Malfunction of Power Supply Circuit System
      • Comments On Trouble Symptom
      • Probable Causes
      • Diagnosis
    • INSPECTION PROCEDURE 6: When the ECO Mode Switch is Turned On, the Drive Mode is not Switched into AWC ECO Mode
      • Comments On Trouble Symptom
      • Probable Causes
      • Diagnostic Procedure
  • Data List Reference Table
  • Special Function
    • Reset
    • Test
  • Check At AWC-Ecu Terminal
• Special Tools
• On-Vehicle Service
  • Control System Component Part Configuration Diagram
  • Essential Service
    • Transmission Fluid Check
    • Transmission Fluid Change
    • FLUSHING COOLERS AND TUBES <Vehicles WITH AIR-COOLED OIL COOLER ASSEMBLY>
    • Oil Cooler Flow Check
    • Transmission Range Switch Continuity Check
    • Transmission Range Switch And Control Cable Adjustment
  • Transfer Oil Check <AWD>
  • Transfer Oil Change <AWD>
  • ELECTRONIC CONTROL COUPLING OPERATION CHECK <Vehicles WITH S-AWC>
  • CVT Control Component Check
    • Transmission Range Switch Check
    • Solenoid Valve Check
    • Valve Body Harness Check
    • Transmission Fluid Temperature Sensor Check
    • ELECTRONIC CONTROL COUPLING SOLENOID (CENTER) CHECK <Vehicles WITH S-AWC>
  • Selector Lever Operation Check
  • Shift Lock Mechanism Check
    • System Check
    • Component Parts Check
      • Shift Lock Link
      • Shift Lock Solenoid
• Transaxle Control
  • Removal And Installation
  • Selector Lever Assembly Continuity Check
    • Switch Check
    • KEY LOCK RELAY CHECK <Vehicles WITHOUT KOS>
• Oil Seal
  • Removal And Installation
    • Notes
    • Removal Service Points
      • <<A>> Side Oil Seal (LH) Removal
      • <<B>> Side Oil Seal (RH) Removal
    • Installation Service Points
      • >>A<< Side Oil Seal (LH) Installation
      • >>B<< Side Oil Seal (RH) Installation
• Oil Filter
  • Removal And Installation
• Oil Pan And Valve Body Assembly
  • Removal And Installation
    • Notes
    • Removal Service Points
      • <<A>> Snap Ring Removal
      • <<B>> Valve Body Assembly Removal
    • Installation Service Points
      • >>A<< Lip Seal Installation
      • >>B<< Valve Body Assembly Installation
      • >>C<< Oil Strainer Installation
      • >>D<< Oil Pan Gasket Installation
      • >>E<< Oil Pan Installation
• Transmission Range Switch
  • Removal And Installation
• Sensors
  • Removal And Installation
• Transaxle Assembly
  • Removal And Installation
    • Notes
    • Removal Service Points
      • <<A>> CVT Assembly Connector Disconnection
      • <<B>> Injector Protector Mounting Bolt Removal
      • <<C>> Torque Converter And Drive Plate Coupling Bolt Removal
      • <<D>> Transaxle Assembly Coupling Bolt Removal
      • <<E>> Engine Assembly Holding
    • Installation Service Points
      • >>A<< Transaxle Assembly Installation
      • >>B<< Injector Protector Mounting Bolt Installation
      • >>C<< Transaxle Control Cable Installation
• Transfer Assembly
  • Removal And Installation
    • Notes
    • Removal Service Point
      • <<A>> Transfer Assembly Removal
• Transaxle Control Module (TCM)
  • Removal And Installation
• AWC-ECU
  • Removal And Installation
• DRIVE MODE SELECTOR
  • Removal And Installation
  • Drive Mode Selector Inspection
• Transmission Fluid Cooler And Cooler Line
  • Removal And Installation
    • Notes
    • <Vehicles without air-cooled oil cooler assembly>
    • <Vehicles with air-cooled oil cooler assembly>
• Paddle Shift Assembly
  • Removal And Installation
  • Paddle Shift Switch Check