LEMON Manuals: Even more car manuals for everyone
Home >> Mitsubishi >> 2019 >> Outlander LE, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 68 (Door) >> Specifications >> Special Tools

Special Tools

WARNING: This page is about a different car, the 2018 Mitsubishi Outlander. However, it is still accessible from the selected car via links, so may be relevant.
Tool Tool number and name Supersession Application
G04872200Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
 MB990480 Glass holder General service tool Removal and installation of power window regulator
G04872297Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
 MB990900 or MB991164 Door adjusting wrench MB990900-01 Adjustment of door fit
G05384137Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
 MB990925 Bearing and oil seal installer set
  1. MB990939 Remover bar
 MB990925-01 or General service tool Adjustment of door striker
G05375609Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
 MB990211 Slider hammer MB990211-01
G05384139Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
 MB990241 Axle shaft puller
  1. MB990243 Body puller
 MB990241-01 or General service tool
G09628470Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  1. MB992744
  2. MB992745
  3. MB992746
  4. MB992747
  5. MB992748
  1. Vehicle communication interface-Lite (V.C.I.-Lite)
  2. V.C.I.-Lite main harness A (for vehicles with CAN communication)
  3. V.C.I.-Lite main harness B (for vehicles without CAN communication)
  4. V.C.I.-Lite USB cable short
  5. V.C.I.-Lite USB cable long
 -
  • Diagnostic trouble code, service data, actuator test check
  • Registration of ID codes
G06244449Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
 MB991955
  1. MB991824
  2. MB991827
  3. MB991910
  4. MB991911
  5. MB991825
  6. MB991826 M.U.T.-III sub-assembly
  1. Vehicle communication interface (V.C.I.)
  2. M.U.T.-III USB cable
  3. M.U.T.-III main harness A (for vehicles with CAN communication)
  4. M.U.T.-III main harness B (for vehicles without CAN communication)
  5. Measuring adapter harness
  6. M.U.T.-III trigger harness
 MB991824-KIT
NOTE: G: MB991826 M.U.T.-III Trigger Harness is not necessary when pushing V.C.I. ENTER key.
CAUTION: M.U.T.-III main harness A (MB991910) should be used. M.U.T.-III main harness B and C should not be used for this vehicle.
ETACS-ECU check (Diagnostic trouble code, service data)
G09625236Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
 MB991223
  1. MB991219
  2. MB991220
  3. MB991221
  4. MB991222

Harness set
  1. Test harness
  2. LED harness
  3. LED harness adaptor
  4. Probe
 General service tools Continuity check and voltage measurement at harness wire or connector for loose, corroded or damaged terminals, or terminals pushed back in the connector.
  1. Connector pin contact pressure inspection
  2. Power circuit inspection
  3. Power circuit inspection
  4. Commercial tester connection
G08294095Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
 MB992006 Extra fine probe - Making voltage and resistance measurement during troubleshooting
scientia non olet · About LEMON Manuals