LEMON Manuals: Even more car manuals for everyone
Home >> Mitsubishi >> 2018 >> Eclipse Cross SEL >> Repair and Diagnosis >> External Pages >> Different car >> Section 36 (Engine Mechanical) >> Special Tools

Special Tools

WARNING: This page is about a different car, the 2017 Mitsubishi Mirage. However, it is still accessible from the selected car via links, so may be relevant.
Tool Tool number and name Supersession Application
G09667990
 MB992080
  1. MB992081
  2. MB992082

Belt tension meter set
  1. Belt tension meter
  2. Microphone assembly
 Tool not available Drive belt tension check
G09628470
  1. MB992744
  2. MB992745
  3. MB992746
  4. MB992747
  5. MB992748

  1. Vehicle communication interface-Lite (V.C.I.-Lite)
  2. V.C.I.-Lite main harness A (for vehicles with CAN communication)
  3. V.C.I.-Lite main harness B (for vehicles without CAN communication)
  4. V.C.I.-Lite USB cable short
  5. V.C.I.-Lite USB cable long
 -
CAUTION: V.C.I.-Lite main harness A (MB992745) should be used. V.C.I.-Lite main harness B (MB992746) should not be used for this vehicle.
  • Checking the ignition timing
  • Checking the idle speed
  • Erasing the diagnostic trouble code (DTC)
G05105023
 MB991958
  1. MB991824
  2. MB991827
  3. MB991910
  4. MB991911
  5. MB991914
  6. MB991825
  7. MB991826

M.U.T.-III sub-assembly
  1. Vehicle communication interface (V.C.I.)
  2. M.U.T.-III USB cable
  3. M.U.T.-III main harness A (Vehicles with CAN communication system)
  4. M.U.T.-III main harness B (Vehicles without CAN communication system)
  5. M.U.T.-III main harness C (for Chrysler models only)
  6. M.U.T.-III measurement adapter
  7. M.U.T.-III trigger harness
 MB991824-KIT
NOTE: G: MB991826 M.U.T.-III Trigger Harness is not necessary when pushing V.C.I. ENTER key.
CAUTION: M.U.T.-III main harness A (MB991910) should be used. M.U.T.-III main harness B (MB991911) and M.U.T.-III main harness C (MB991914) should not be used for this vehicle.
  • Checking the ignition timing
  • Checking the idle speed
  • Erasing the DTC
G06247481
 MB990767
Front hub and flange yoke holder		 MB990767-01 Holding the crankshaft pulley
G05374078
 MD998719
Pin		 MIT308239
G09628194
 MB991992
Torque wrench adaptor		 - V.V.T. sprocket bolt removal and installation
G05374080
 MD998772
Valve spring compressor		 General service tool Valve spring compression
G05374081
 MB992090
Retainer holder attachment		 -
G11277351
 MB992089
Retainer holder C		 -
G11277352
 MB992085
Valve stem seal pliers		 - Valve stem seal removal
G09628199
 MB992922
Valve stem seal installer adjustable		 - Valve stem seal press-fitting
G09667999
 MD998727
Oil pan FIPG cutter		 MD998727-01 Oil pan removal
G09628201
 MB991993
Crankshaft front oil seal guide		 - Front oil seal installation
G11277356
 MB990699
Differential oil seal installer		 -
G06247480
 MB991928
  1. MB991929
  2. MB991930
  3. MB991931
  4. MB991932
  5. MB991933
  6. MB991934

Engine hanger
  1. Joint (50) x 2
  2. Joint (90) x 2
  3. Joint (140) x 2
  4. Foot (standard) x 4
  5. Foot (short) x 2
  6. Chain and hook assembly
 Tool not available Supporting the engine assembly
G05431338
 MB991895
Engine hanger		 Tool not available
G09628206
 MB992906
Engine hanger attachment		 -
G09628207
 MB992336
  1. MB992353 x 2
  2. MB992354 x 2

EV battery cart
  1. Rigid caster
  2. Swivel caster
 - Engine assembly removal and installation
scientia non olet · About LEMON Manuals