Common Specs & Procedures
OUTLANDER COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | |||
| Automatic & Manual | GENERAL SPECIFICATIONS | ||
| Torque | See appropriate figure in HEATING, AIR CONDITIONING AND VENTILATION article. | ||
| Axle Nut/Hub Nut | |||
| Front | 144-176 N.m (107-129 ft-lb) | ||
| Rear (2WD) | 81-109 N.m (60-80 ft-lb) | ||
| Rear (AWD) | 144-176 N.m (107-129 ft-lb) | ||
| Battery | GENERAL INFORMATION | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | GENERAL SPECIFICATIONS and SERVICE SPECIFICATIONS | ||
| Torque | REMOVAL AND INSTALLATION (Front Disc Brake Assembly) and REMOVAL AND INSTALLATION < 2.4L ENGINE: 5 PERSONS SEAT > or REMOVAL AND INSTALLATION < 2.4L ENGINE: 7 PERSONS SEAT, 3.0L ENGINE > (Rear Disc Brake Assembly) | ||
| Drum Brakes (Parking Brake) | |||
| Service Specifications | SERVICE SPECIFICATIONS and PARKING BRAKE LINING AND DRUM | ||
| Torque | PARKING BRAKE LINING AND DRUM | ||
| Charging | |||
| Generator | SERVICE SPECIFICATIONS | ||
| Torque | |||
| 2.4L | REMOVAL AND INSTALLATION < 2.4L ENGINE > | ||
| 3.0L | REMOVAL AND INSTALLATION < 3.0L ENGINE > | ||
| Drive Belts | |||
| Adjustment | 8. DRIVE BELT (FOR GENERATOR, POWER STEERING OIL PUMP) (CHECK CONDITION) | ||
| Belt Routing | |||
| 2.4L | >> B << DRIVE BELT INSTALLATION | ||
| 3.0L | CRANKSHAFT PULLEY | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE SPECIFICATIONS | ||
| Radiator Cap Pressure | Standard value: 93 - 123 kPa (14 - 18 psi), Minimum limit: 83 kPa (12 psi) | ||
| Thermostat R & I | |||
| 2.4L | REMOVAL AND INSTALLATION < 2.4L ENGINE > | ||
| 3.0L | REMOVAL AND INSTALLATION < 3.0L ENGINE > | ||
| Water Pump R & I | |||
| 2.4L | REMOVAL AND INSTALLATION < 2.4L ENGINE > | ||
| 3.0L | REMOVAL AND INSTALLATION < 3.0L ENGINE > | ||
| Engine Mechanical | |||
| 2.4L | |||
| Compression | Standard value (at engine speed of 200 RPM): 1,440 kPa (209 psi). Minimum limit (at engine speed of 200 RPM): 1,000 kPa (145 psi). Difference between cylinders: Limit: 98 kPa (14 psi). | ||
| Oil Pressure | Oil pressure at curb idle is 29 kPa (4.2 psi) or more. At 3,500 RPM: 294 - 686 kPa (43 - 100 psi). | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 3.0L | |||
| Compression | Standard value (at engine speed of 200 RPM): 1,650 kPa (239 psi). Minimum limit (at engine speed of 200 RPM): 1,150 kPa (167 psi). Difference between cylinders: Limit: 98 kPa (14 psi). | ||
| Oil pressure | Oil pressure at curb idle is 29 kPa (4.2 psi) or more. At 3,500 RPM: 294 - 686 kPa (43 - 100 psi) | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate | |||
| 2.4L | 40 N.m (30 ft-lb) → 130 N.m (96 ft-lb) | ||
| 3.0L | 76 ± 4 N.m (57 ± 2 ft-lb) | ||
| Fuel System | |||
| Pressure Specification | At curb Idle Standard value: Approximately : 324 kPa (47 psi) | ||
| Fuel Pressure Test Procedure | |||
| 2.4L | FUEL PRESSURE TEST | ||
| 3.0L | FUEL PRESSURE TEST | ||
| Fuel Filter Location | FUEL PUMP MODULE REPLACEMENT < FWD > or FUEL PUMP MODULE REPLACEMENT < AWD > | ||
| Fuel Filter R & I | FUEL PUMP MODULE REPLACEMENT < FWD > or FUEL PUMP MODULE REPLACEMENT < AWD > | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 2.4L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| 3.0L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil on plug | ||
| Ignition Wires (Routing) | |||
| 2.4L | Coil on plug | ||
| 3.0L | Coil on plug | ||
| Spark Plug | |||
| 2.4L | |||
| Type | NGK: DIFR5C11 | ||
| Gap | Standard Value: 0.039-0.043 in. (1.0-1.1 mm). Limit: 1.3 mm (0.051 in.) | ||
| Torque | 25 +/- 5 N. m (19 +/- 3 ft-lb). | ||
| 3.0L | |||
| Type | NGK: ILKR7B-8 / DENSO: SXU22HDR8 | ||
| Gap | Standard Value: 0.028-0.031 in. (0.7-0.8 mm). Limit: 0.95 mm (0.037 in.) | ||
| Torque | 18 +/- 2 N. m (13 +/- 1 ft-lb). | ||
| Starting | |||
| Starter | GENERAL SPECIFICATIONS and SERVICE SPECIFICATIONS | ||
| Torque | |||
| 2.4L | See figure in REMOVAL AND INSTALLATION < 2.4L ENGINE > | ||
| 3.0L | See figure in REMOVAL AND INSTALLATION < 3.0L ENGINE > | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | SERVICE SPECIFICATIONS | ||
| Rear | SERVICE SPECIFICATIONS | ||
| Torque | |||
| Front | FASTENER TIGHTENING SPECIFICATIONS | ||
| Rear | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 66-80 ft. lbs (88-108 N.m) | ||