LEMON Manuals: Even more car manuals for everyone
Home >> Mitsubishi >> 2006 >> Outlander LS, AWD, Automatic >> Repair and Diagnosis >> Electrical >> Body Electrical >> Simplified Wiring System >> SWS Diagnosis >> Service Data Check

Service Data Check

  1. Use the scan tool and the SWS monitor kit to check "DATA LIST" or "FUNCTION DIAG."

    This "DATA LIST" or "FUNCTION DIAG." check is applicable for signals, which are transmitted and received through the SWS communication line. For input signals, which are not compatible with the SWS monitor kit, refer to the Pulse Check procedure (by using the scan tool or voltmeter) PULSE CHECK .

    < DATA LIST REFERENCE TABLE >

    The table below shows the service data and their normal condition, which are displayed during the "DATA LIST."

  2. The following input signals can be checked by using the scan tool and the SWS monitor kit.
NOTE: If a problem is found in the "Service Data" check, refer to Input Signal Chart INPUT SIGNAL CHART .
COLUMN ECU (COLUMN SWITCH) REFERENCE CHART

CHECK ITEMS ITEM NO. DISPLAY ON SCAN TOOL CHECK CONDITIONS NORMAL CONDITIONS
Dimmer switch 02 DIMMER SW Dimmer switch: ON ON
Dimmer switch: OFF OFF
Windshield washer switch 09 FRONT WASH.SW Windshield washer switch: ON ON
Windshield washer switch: OFF OFF
Headlight switch 00 HEADLIGHT SW Lighting switch: HEAD ON
Lighting switch: Other than HEAD OFF
Windshield high-speed wiper switch 07 HI WIPER SW Wiper switch: HI ON
Wiper switch: Other than HI OFF
With or without windshield intermittent wiper interval adjusting knob 15 INT WIPE KNOB Vehicles with intermittent wiper adjusting knob EQUIP
Vehicles without intermittent wiper adjusting knob NON
Windshield intermittent wiper switch 05 INT WIPER SW Wiper switch: INT ON
Wiper switch: Other than INT OFF
Windshield low-speed wiper switch 06 LO WIPER SW Wiper switch: LO ON
Wiper switch: Other than LO OFF
Wind shield mist wiper switch 08 MIST WIPER SW Wiper switch: Mist ON
Wiper switch: Other than "Mist" position OFF
Passing light switch 03 PASSING SW Passing light switch: ON ON
Passing light switch: OFF OFF
Tail light switch 01 TAILLIGHT SW Lighting switch: TAIL ON
Lighting switch: OFF OFF
Turn-signal light switch (LH) 11 T/S LH SW Turn-signal light switch: LH ON
Turn-signal light switch: Other than LH OFF
Turn-signal light switch: RH 10 T/S RH SW Turn-signal light switch: RH ON
Turn-signal light switch: Other than RH OFF
Rear wiper switch 13 REAR WIPER SW Rear wiper switch: INT ON
Rear wiper switch: Other than INT OFF
Rear washer switch 14 REAR WASH.SW Rear wiper switch: Washer ON
Rear wiper switch: Other than "Washer" position OFF
ETACSECU CONDITIONS REFERENCE CHART

CHECK ITEMS ITEM NO. DISPLAY ON SCAN TOOL CHECK CONDITIONS NORMAL CONDITIONS
Tone alarm 43 BUZZER
  1. Ignition switch: LOCK (OFF)
  2. Key reminder switch: ON
  3. Front door switch: ON (front door open)
 ON
When requirements for sounding each warning tone alarm are not satisfied OFF
Front door switch 32 FRONT DOOR SW Front door switch (right or left): right or left door switch is on (right or left front door is open) ON
Front door switches (right and left): both right and left door switches are off (both right and left front doors are closed) OFF
Front fog lights 36 F.FOG LIGHT
  1. Lighting switch: HEAD
  2. Fog light switch: ON
 ON
Other than the condition above OFF
Headlight automatic shutdown function 35 H/L AUTO-CUT
  1. Lighting switch: Other than OFF
  2. Ignition switch: from ON or START to LOCK (OFF) or ACC
  3. Front door switch: ON (front door open)
 OFF to ON (after approximately one second)
When requirements for the headlight automatic shutdown are not satisfied OFF
Ignition switch (IG1) 30 IG SW (IG1) Ignition switch: ON or START ON
Ignition switch: LOCK (OFF) or ACC OFF
Ignition switch (ACC) 31 IG SW (ACC) Ignition switch: ACC or ON ON
Ignition switch: LOCK (OFF) or START OFF
Park/neutral switch ("R" position) 41 INHIBITOR SW Park/Neutral position switch: R position ON
Park/Neutral position switch: Other than R position OFF
Windshield intermittent wiper interval 37 INT WIPE TIME
  1. Ignition switch: ACC or ON
  2. Operate the intermittent wiper adjusting knob, and change the wiper interval
 The scan tool displays intermittent wiper interval in response to the intermittent wiper adjusting knob positions
NOTE: For item No.43, the scan tool also displays "ON" when the light reminder tone alarm or the seat belt theft-alarm function is triggered.
FRONT ECU CONDITIONS REFERENCE CHART

CHECK ITEMS ITEM NO. DISPLAY ON SCAN TOOL CHECK CONDITIONS NORMAL CONDITIONS
Response by the front-ECU 70 FRONT ECU ACK Lighting switch is at position other than OFF (excluding when high-beam is on) or the wiper switch is at position other than OFF NORMAL ACK
  • Ignition switch: ON or START
  • Lighting switch: OFF
  • Wiper switch: OFF
 SLEEP ACK
  • Lighting switch: HEAD
  • Headlight: High-beam
 HI-BEAM ACK
Except above conditions NO ACK
NOTE: For item No. 70, the scan tool also displays "A/G" under the "ECU COMM CHK" when it displays "NO ACK" under the front-ECU check.
SUNROOF ECU (SUNROOF MOTOR ASSEMBLY) CONDITIONS REFERENCE CHART

CHECK ITEMS ITEM NO. DISPLAY ON SCAN TOOL CHECK CONDITIONS NORMAL CONDITIONS
Response by the sun roof-ECU 72 S/R ECU ACK
  1. Ignition switch: ON or START
  2. While sunroof is off
 NORMAL ACK SLEEP ACK (after approximately 30 seconds)
  1. Ignition switch: ON or START
  2. One of the sunroof switches is on
 INPUT CHECK - NORMAL ACK
Except above conditions NO ACK
NOTE: For item No. 72, the scan tool also displays "A/G" under the "ECU COMM CHK" when it displays "No response" under the sunroof-ECU check.

< FUNCTION DIAGNOSIS >

The table below shows the service data and their normal condition, which are displayed during the "FUNCTION DIAG." The row "NORMAL CONDITIONS" shows values, which are shown when each operation is made.

WIPER CONDITIONS REFERENCE CHART

ITEMS ITEM NO. INPUT SIGNALS DISPLAY ON SCAN TOOL NORMAL CONDITIONS
F.WIPER HI 05 Windshield intermittent wiper switch INT WIPER SW OFF
06 Windshield low-speed wiper switch LO WIPER SW OFF
07 Windshield high-speed wiper switch HI WIPER SW ON
08 Wind shield mist wiper switch MIST WIPER SW OFF
09 Windshield washer switch FRONT WASH.SW OFF
31 Ignition switch (ACC) IG SW (ACC) ON
70 Response by the front-ECU FRONT ECU ACK NORMAL ACK or HI-BEAM ACK
F.WIPER INT 05 Windshield intermittent wiper switch INT WIPER SW ON
06 Windshield low-speed wiper switch LO WIPER SW OFF
07 Windshield high-speed wiper switch HI WIPER SW OFF
08 Wind shield mist wiper switch MIST WIPER SW OFF
09 Windshield washer switch FRONT WASH.SW OFF
31 Ignition switch (ACC) IGSW(ACC) ON
37 Windshield intermittent wiper interval INT WIPE TIME The scan tool displays intermittent wiper interval in response to the intermittent wiper adjusting knob positions
70 Response by the front-ECU FRONT ECU ACK NORMAL ACK or HI-BEAM ACK
F.WIPER LO 05 Windshield intermittent wiper switch INT WIPER SW OFF
06 Windshield low-speed wiper switch LO WIPER SW ON
07 Windshield high-speed wiper switch HI WIPER SW OFF
08 Wind shield mist wiper switch MIST WIPER SW OFF
09 Windshield washer switch FRONT WASH.SW OFF
31 Ignition switch (ACC) IG SW (ACC) ON
70 Response by the front-ECU FRONT ECU ACK NORMAL ACK or HI-BEAM ACK
F.WIPER MIST 05 Windshield intermittent wiper switch INT WIPER SW OFF
06 Windshield low-speed wiper switch LO WIPER SW OFF
07 Windshield high-speed wiper switch HI WIPER SW OFF
08 Wind shield mist wiper switch MIST WIPER SW ON
09 Windshield washer switch FRONT WASH.SW OFF
31 Ignition switch (ACC) IG SW (ACC) ON
70 Response by the front-ECU FRONT ECU ACK NORMAL ACK or HI-BEAM ACK
F.WIPER WASH 08 Wind shield mist wiper switch MIST WIPER SW OFF
09 Windshield washer switch FRONT WASH.SW ON
31 Ignition switch (ACC) IG SW (ACC) ON
70 Response by the front-ECU FRONT ECU ACK NORMAL ACK or HI-BEAM ACK
REAR WIPER CONDITIONS REFERENCE CHART

ITEMS ITEM NO. INPUT SIGNALS DISPLAY ON SCAN TOOL NORMAL CONDITIONS
REAR WASHER 14 Rear washer switch REAR WASH.SW ON
31 Ignition switch (ACC) IG SW (ACC) ON
REAR WIPER 13 Rear wiper switch REAR WIPER SW ON
14 Rear washer switch REAR WASH.SW OFF
31 Ignition switch (ACC) IG SW (ACC) ON
REV.INTERLO CK 13 Rear wiper switch REAR WIPER SW ON
31 Ignition switch (ACC) IG SW (ACC) ON
41 Park/neutral switch ("R" position) PN PSW (R) ON
LIGHTING CONDITIONS REFERENCE CHART

ITEMS ITEM NO. INPUT SIGNALS DISPLAY ON SCAN TOOL NORMAL CONDITIONS
H/L AUTO-CUT 00 Headlight switch HEADLIGHT SW Either is on
01 Tail light switch TAILLIGHT SW
30 Ignition switch (IG1) IG SW (IG1) OFF
32 Front door switch FRONT DOOR SW ON
35 Headlight automatic shutdown function H/L AUTO-CUT ON
70 Response by the front-ECU FRONT ECU ACK NORMAL ACK or HI-BEAM ACK
OFF 00 Headlight switch HEADLIGHT SW OFF
01 Tail light switch TAILLIGHTSW OFF
03 Passing light switch PASSING SW OFF
30 Ignition switch (IG1) IG SW (IG1) ON
35 Headlight automatic shutdown function H/L AUTO-CUT OFF
70 Response by the front-ECU FRONT ECU ACK NORMAL ACK or SLEEP ACK
HEADLIGHT HI 00 Headlight switch HEADLIGHT SW ON
02 Dimmer switch DIMMER SW ON
03 Passing light switch PASSING SW ON
30 Ignition switch (IG1) IG SW (IG1) ON
35 Headlight automatic shutdown function H/L AUTO-CUT OFF
70 Response by the front-ECU FRONT ECU ACK HI-BEAM ACK
HEADLIGHT LO 00 Headlight switch HEADLIGHT SW ON
03 Passing light switch PASSING SW OFF
30 Ignition switch (IG1) IG SW (IG1) ON
35 Headlight automatic shutdown function H/L AUTO-CUT OFF
70 Response by the front-ECU FRONT ECU ACK NORMAL ACK
PASSING LIGHT 03 Passing light switch PASSING SW ON
70 Response by the front-ECU FRONT ECU ACK NORMAL ACK or HI-BEAM ACK
TAILLIGHT 00 Headlight switch HEADLIGHT SW OFF
01 Tail light switch TAILLIGHT SW ON
03 Passing light switch PASSING SW OFF
30 Ignition switch (IG1) IG SW (IG1) ON
35 Headlight automatic shutdown function H/L AUTO-CUT OFF
70 Response by the front-ECU FRONT ECU ACK NORMALACK
F.FOG LIGHT 00 Headlight switch HEADLIGHT SW ON
30 Ignition switch (IG1) IGSW(IG1) ON
35 Headlight automatic shutdown function H/L AUTO-CUT OFF
36 Front fog lights F.FOG LIGHT ON
70 Response by the front-ECU FRONT ECU ACK NORMAL ACK
NOTE: When checking the input signals (off, tail, low-beam or high-beam), turn the ignition switch to the "ON" position in order to disable the headlight automatic shutdown function. However, the headlight operation does not depend on the ignition switch positions, the scan tool does not display the title "IGNITION SWITCH".

For checking item "HI (High-beam)", the scan tool displays "OFF" on the item No.2 "Dimmer SW" when the headlights are at high-beam. Therefore, the scan tool should display "ON" momentarily when the dimmer switch is operated.

TURN SIGNAL CONDITIONS REFERENCE CHART

ITEMS ITEM NO. INPUT SIGNALS DISPLAY ON SCAN TOOL NORMAL CONDITIONS
TURN-SIG.LH 10 Turn-signal light switch (RH) T/S RH SW OFF
11 Turn-signal light switch (LH) T/S LH SW ON
30 Ignition switch (IG1) IG SW (IG1) ON
TURN-SIG.RH 10 Turn-signal light switch (RH) T/S RH SW ON
11 Turn-signal light switch (LH) T/S LH SW OFF
30 Ignition switch (IG1) IG SW (IG1) ON
BUZZER CONDITIONS REFERENCE CHART

ITEMS ITEM NO. INPUT SIGNALS DISPLAY ON SCAN TOOL NORMAL CONDITIONS
KEY REMND.ALM 30 Ignition switch (IG1) IG SW (IG1) OFF
32 Front door switch FRONT DOOR SW ON
43 Tone alarm BUZZER ON
LGT MONI.ALM 00 Headlight switch HEADLIGHT SW Either is on
01 Tail light switch TAILLIGHT SW
30 Ignition switch (IG1) IG SW (IG1) OFF
32 Front door switch FRONT DOOR SW ON
35 Headlight automatic shutdown function H/L AUTO-CUT OFF
43 Tone alarm BUZZER ON
OTHER ALARM 30 Ignition switch (IG1) IG SW (IG1) ON
43 Tone alarm BUZZER ON
NOTE: The headlight automatic shutdown function works in approximately one second after the lighting monitor tone alarm starts sounding, and then the tone alarm ceases sounding.
SUNROOF CONDITIONS REFERENCE CHART

ITEMS ITEM NO. INPUT SIGNALS DISPLAY ON SCAN TOOL NORMAL CONDITIONS
SUNROOF OPE. 30 Ignition switch (IG1) IG SW (IG1) ON
72 Response by the sunroof-ECU S/R ECU ACK INPUT CHECK (only momentarily when switch is operated)
scientia non olet · About LEMON Manuals