Fastener Tightening Specifications
FASTENER TIGHTENING SPECIFICATIONS
| ITEM | SPECIFICATION | |
|---|---|---|
| Camshaft and valve stem seal | ||
| Camshaft bearing cap bolt | 20 +/- 1 N. m (14 +/- 0.5 ft-lb) | |
| Camshaft sprocket cap | 32 +/- 2 N. m (24 +/- 1 ft-lb) | |
| Camshaft position sensing cylinder bolt | 22 +/- 4 N. m (16 +/- 3 ft-lb) | |
| Camshaft position sensor support bolt | 14 +/- 1 N. m (120 +/- 13 in-lb) | |
| Camshaft position sensor support cover bolt | 10 +/- 2 N. m (89 +/- 17 in-lb) | |
| Camshaft sprocket bolt (inlet side) | 65 +/- 5 N. m (48 +/- 4 ft-lb) | |
| Camshaft sprocket bolt (exhaust side) | 89 +/- 9 N. m (65 +/- 7 ft-lb) | |
| Control wiring harness bracket bolt | 11 +/- 1 N. m (98 +/- 8 in-lb) | |
| Ground terminal bolt (control wiring harness) | 5.0 +/- 1.0 N. m (44 +/- 9 in-lb) | |
| Heated oxygen sensor (front) bolt | 10.5 +/- 0.5 N. m (93 +/- 4 in-lb) | |
| Oil delivery body bolt | 11 +/- 1 N. m (98 +/- 8 in-lb) | |
| Oil feeder control valve bolt | 11 +/- 1 N. m (98 +/- 8 in-lb) | |
| Rocker cover bolt | 3.5 +/- 0.5 N. m (31 +/- 4 in-lb) | |
| Rocker cover center cover bolt | 3.0 +/- 0.5 N. m (27 +/- 4 in-lb) | |
| Spark plug | 25 +/- 4 N. m (18 +/- 3 ft-lb) | |
| Vacuum pipe bolt | 11 +/- 1 N. m (98 +/- 8 in-lb) | |
| Crankshaft oil seal | ||
| Flywheel bolt | 132 +/- 5 N. m (98 +/- 3 ft-lb) | |
| Crankshaft pulley | ||
| Crankshaft damper pulley bolt | 25 +/- 4 N. m (18 +/- 3 ft-lb) | |
| Cylinder head gasket | ||
| Check valve assembly | 30 +/- 3 N. m (22 +/- 2 ft-lb) | |
| Cylinder head bolt < Cold engine > | 78 +/- 2 N. m to 0 N. m to 20 +/- 2 N. m to + 90° to + 90° (58 +/- 1 ft-lb to 0 in-lb to 15 +/- 1 ft-lb to + 90° to + 90°) | |
| EGR solenoid valve and bracket assembly bolt | 9.0 +/- 1.0 N. m (80 +/- 9 in-lb) | |
| Engine oil dipstick guide bolt | 13 +/- 1 N. m (115 +/- 9 in-lb) | |
| Eye bolt | 42 +/- 2 N. m (31 +/- 1 ft-lb) | |
| Fuel high-pressure hose bolt | 5.0 +/- 1.0 N. m (44 +/- 9 in-lb) | |
| Generator brace bolt | 20 +/- 2 N. m (15 +/- 1 ft-lb) | |
| Ground cable bolt | 5.0 +/- 1.0 N. m (44 +/- 9 in-lb) | |
| Ground terminal bolt (control wiring harness) | 5.0 +/- 1.0 N. m (44 +/- 9 in-lb) | |
| Inlet manifold stay bolt | 31 +/- 3 N. m (23 +/- 2 ft-lb) | |
| Oil feeder control valve pipe bolt | 11 +/- 1 N. m (98 +/- 8 in-lb) | |
| Oil return tube bolt (bolt, flange) | M6 | 14 +/- 1 N. m (120 +/- 13 in-lb) |
| Oil return tube bolt (bolt, washer assembled) | M6 | 9.0 +/- 1.0 N. m (80 +/- 9 in-lb) |
| Turbocharger bracket bolt | 35 +/- 6 N. m (26 +/- 4 ft-lb) | |
| Engine assembly | ||
| Engine mounting insulator and cushion stopper nut (flange nut, self locking) | M10 | 67 +/- 7 N. m (50 +/- 5 ft-lb) |
| Engine mounting insulator and cushion stopper nut (nut, assembled) | M12 | 98 +/- 10 N. m (73 +/- 7 ft-lb) |
| Engine oil cooler line eye bolt | 42 +/- 2 N. m (31 +/- 1 ft-lb) | |
| Fuel high-pressure hose bolt | 5.0 +/- 1.0 N. m (44 +/- 9 in-lb) | |
| Generator terminal nut | 14 +/- 3 N. m (124 +/- 26 in-lb) | |
| Ground cable bolt | 5.0 +/- 1.0 N. m (44 +/- 9 in-lb) | |
| Ground terminal bolt (battery wiring harness) | 26 +/- 5 N. m (19 +/- 4 ft-lb) | |
| Ground terminal bolt (control wiring harness) | 5.0 +/- 1.0 N. m (44 +/- 9 in-lb) | |
| Power steering oil pressure hose bolt | 12 +/- 2 N. m (102 +/- 22 in-lb) | |
| Power steering oil pump and bracket assembly bolt | M8 | 22 +/- 4 N. m (16 +/- 3 ft-lb) |
| M10 | 40 +/- 5 N. m (30 +/- 3 ft-lb) | |
| Power steering oil pump heat protector bolt | 22 +/- 4 N. m (16 +/- 3 ft-lb) | |
| Power steering oil reservoir bolt | 12 +/- 2 N. m (102 +/- 22 in-lb) | |
| Turbocharger wastegate actuator bolt | 11 +/- 1 N. m (98 +/- 8 in-lb) | |
| Oil pan | ||
| Cylinder block baffle bolt | 22 +/- 4 N. m (16 +/- 3 ft-lb) | |
| Engine oil cooler line eye bolt | 42 +/- 2 N. m (31 +/- 1 ft-lb) | |
| Engine oil pan bolt | 9.0 +/- 3.0 N. m (80 +/- 26 in-lb) | |
| Engine oil pan drain plug | 39 +/- 5 N. m (29 +/- 3 ft-lb) | |
| Flywheel housing front lower cover bolt (bolt, flange) | M6 | 10 +/- 2 N. m (89 +/- 17 in-lb) |
| Flywheel housing front lower cover bolt (bolt, flange) | M10 | 26 +/- 5 N. m (19 +/- 4 ft-lb) |
| Flywheel housing front lower cover bolt (bolt, washer assembled) | M6 | 9.0 +/- 1.0 N. m (80 +/- 9 in-lb) |
| Oil return tube bolt (bolt, flange) | M6 | 14 +/- 1 N. m (120 +/- 13 in-lb) |
| Oil return tube bolt (bolt, washer assembled) | M6 | 9.0 +/- 1.0 N. m (80 +/- 9 in-lb) |
| Timing belt | ||
| Auto-tensioner bolt (bolt, flange) | M8 | 24 +/- 4 N. m (18 +/- 3 ft-lb) |
| Auto-tensioner bolt (bolt, washer assembled) | M10 | 44 +/- 10 N. m (33 +/- 7 ft-lb) |
| Balancer timing belt tensioner bolt | 19 +/- 3 N. m (14 +/- 2 ft-lb) | |
| Crankshaft position sensor bolt | 8.8 +/- 1.0 N. m (78 +/- 9 in-lb) | |
| Crankshaft pulley center bolt | 167 N. m (123 ft-lb) | |
| Cylinder block plug | 30 +/- 3 N. m (23 +/- 2 ft-lb) | |
| Idler pulley bolt | 79 +/- 5 N. m (59 +/- 3 ft-lb) | |
| Power steering oil pressure hose bolt | 12 +/- 2 N. m (102 +/- 22 in-lb) | |
| Power steering oil pump and bracket assembly bolt | M8 | 22 +/- 4 N. m (16 +/- 3 ft-lb) |
| M10 | 40 +/- 5 N. m (30 +/- 3 ft-lb) | |
| Power steering oil pump bracket bolt | 49 +/- 9 N. m (36 +/- 7 ft-lb) | |
| Power steering oil pump heat protector bolt | 22 +/- 4 N. m (16 +/- 3 ft-lb) | |
| Power steering oil reservoir bolt | 12 +/- 2 N. m (102 +/- 22 in-lb) | |
| Timing belt idler pulley bolt | 35 +/- 6 N. m (26 +/- 4 ft-lb) | |
| Timing belt lower cover bolt (bolt, flange) | M6 | 11 +/- 1 N. m (98 +/- 8 in-lb) |
| Timing belt lower cover bolt (bolt, washer assembled) | M6 | 9.0 +/- 1.0 N. m (80 +/- 9 in-lb) |
| Timing belt tensioner adjuster bolt | 23 +/- 3 N. m (17 +/- 2 ft-lb) | |
| Timing belt tensioner arm bolt | 21 +/- 4 N. m (16 +/- 2 ft-lb) | |
| Timing belt tensioner pulley bolt | 48 +/- 5 N. m (36 +/- 3 ft-lb) | |
| Timing belt upper cover bolt (bolt, flange) | M6 | 11 +/- 1 N. m (98 +/- 8 in-lb) |
| Water pump pulley bolt | 8.8 +/- 1.0 N. m (78 +/- 9 in-lb) | |