Chassis Electrical
- Battery
- Ignition Switch
- General Description
- Equipment Diagnosis
- Ignition Switch Diagnosis
- Introduction To Immobilizer System Diagnosis
- Immobilizer System Diagnostic Troubleshooting Strategy
- Immobilizer System Trouble Code Diagnosis
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- Trouble Symptom Chart
- SYMTPOM Procedures
- INSPECTION PROCEDURE 1: Communication with Scan Tool MB991958 is Impossible.
- INSPECTION PROCEDURE 2: Registering the Ignition Key is Impossible.
- INSPECTION PROCEDURE 3: Engine does not Start (Cranking but no Initial Combustion).
- INSPECTION PROCEDURE 4: The "SECURITY" Indicator Light does not Illuminate.
- Data List Reference Table
- Check At Immobilizer-Ecu
- Special Tools
- On-Vehicle Service
- Ignition Switch
- Combination Meter Assembly And Vehicle Speed Sensor
- Introduction To Combination Meter Diagnosis
- Equipment Diagnosis
- Special Tools
- On-Vehicle Service
- Combination Meter Assembly And Vehicle Speed Sensor
- Headlight, Front Side Marker Light And Position Light Assembly
- Fog Light
- Front Combination Light
- Rear Combination Light
- Backup Light
- Dome Light
- High-Mounted Stoplight
- Rheostat
- Hazard Warning Light Switch
- Column Switch
- Horn
- Cigarette Lighter And Accessory Socket
- Radio With Tape Player
- Radio With Tape Player And Cd Player, Speaker And Antenna Diagnosis
- Introduction To Audio System Diagnosis
- Troubleshooting Strategy
- Trouble Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: When Power Switch is Turned "ON," No Power is Available.
- INSPECTION PROCEDURE 2: No Sound. < Vehicles with amplifier >
- INSPECTION PROCEDURE 3: No Sound from One Speaker.
- INSPECTION PROCEDURE 4: Separate Type CD Payer or CD Auto Changer does not Operate.
- INSPECTION PROCEDURE 5: The Multi-Center Display does not Display the Information Concerning the Audio System Correctly.
- INSPECTION PROCEDURE 6: Noise Appears at Certain Places when Traveling (AM).
- INSPECTION PROCEDURE 7: Noise Appears at Certain Places when Traveling (FM).
- INSPECTION PROCEDURE 8: Mixed with Noise, Only at Night (AM).
- INSPECTION PROCEDURE 9: Broadcasts can be Heard but Both AM and FM have a lot of Noise.
- INSPECTION PROCEDURE 10: There is More Noise on Either AM or FM.
- INSPECTION PROCEDURE 11: There is Noise when Starting the Engine.
- INSPECTION PROCEDURE 12: Some Noise Appears When There is Vibration or Shocks During Traveling.
- INSPECTION PROCEDURE 13: Noise Sometimes Appears on FM during Traveling.
- INSPECTION PROCEDURE 14: Ever-Present Noise.
- INSPECTION PROCEDURE 15: There is Noise but No Reception for Both AM and FM or No Sound from AM, or No Sound from FM.
- INSPECTION PROCEDURE 16: Poor Reception.
- INSPECTION PROCEDURE 17: Distortion on AM or on Both AM and FM.
- INSPECTION PROCEDURE 18: Distortion on FM Only.
- INSPECTION PROCEDURE 19: Using the Auto Select Function, Too Few Automatic Stations are Selected.
- INSPECTION PROCEDURE 20: Preset Station are Erased.
- INSPECTION PROCEDURE 21: CD can Not be Inserted.
- INSPECTION PROCEDURE 22: No Sound. (CD only)
- INSPECTION PROCEDURE 23: CD Sound Skips.
- INSPECTION PROCEDURE 24: Sound Quality is Poor.
- INSPECTION PROCEDURE 25: CD can Not be Ejected.
- INSPECTION PROCEDURE 26: Motor Antenna won't Extend or Retract.
- INSPECTION PROCEDURE 27: Motor Antenna Extends and Reracts but does not Receive Radio Signal.
- Special Tools
- On-Vehicle Service
- Removal And Installation
- Radio With Tape Player And Cd Player, Speaker And Antenna Diagnosis
- Speaker
- Amplifier
- Antenna
- Remote Controlled Radio Switch
- Equipment Diagnosis
- Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: The system does not accept remote controlled radio switches (RH and LH), but accepts radio and CD player switches.
- INSPECTION PROCEDURE 2: The system does not accept the remote controlled radio switch (RH) only.
- INSPECTION PROCEDURE 3: The system does not accept the remote controlled radio switch (LH) only.
- Remote Controlled Radio Switch
- Inspection
- Equipment Diagnosis
- Rear Window Defogger
- Multi-Center Display
- Equipment Diagnosis
- Diagnosis
- Symptom Procedures
- INSPECTION PROCEDURE 1: The Multi-center Display does not Show any Information.
- INSPECTION PROCEDURE 2: Compass is not Displayed.
- INSPECTION PROCEDURE 3: The Compass is not Correct.
- INSPECTION PROCEDURE 4: The Ambient Temperature Screen Displayed "E0°F" (Ambient Sensor Open Circuit) or "-E5°F" (Ambient Sensor Short Circuit). These are Error Message.
- INSPECTION PROCEDURE 5: The Ambient Temperaure and Compass Screen do not Change.
- On-Vehicle Service
- Special Tools
- Removal And Installation
- Equipment Diagnosis
- Theft Alarm
- Specifications