Fastener Tightening Specifications
WARNING: This page is about a different variant/trim than selected.
FASTENER TIGHTENING SPECIFICATIONS (1 OF 3)
| ITEMS | SPECIFICATION |
|---|---|
| Generator and drive belt | |
| Adjusting bolt | 5 +/- 1 N.m (43 +/- 9 in-lb) |
| Adjusting nut lock bolt | 23 +/- 2 N.m (17 +/- 1 ft-lb) |
| Camshaft position sensing cylinder bolt | 22 +/- 4 N.m (16 +/- 3 ft-lb) |
| Camshaft position sensor bolt | 8.8 +/- 1 N.m (78 +/- 9 in-lb) |
| Camshaft position sensor support bolt | 14 +/- 1 N.m (122 +/- 9 in-lb) |
| Crankshaft pulley bolt | 25 +/- 5 N.m (18 +/- 4 ft-lb) |
| Generator brace bolt | 24 +/- 3 N.m (17 +/- 2 ft-lb) |
| Generator pivot bolt nut | 44 +/- 10 N.m (33 +/- 7 ft-lb) |
| Ignition coil bolt | 10 +/- 2 N.m (87 +/- 17 in-lb) |
| Spark plugs | 25 +/- 5 N.m (18 +/- 4 ft-lb) |
| Water pump pulley bolt | 8.8 +/- 1 N.m (78 +/- 9 in-lb) |
| Timing belt | |
| Auto-tensioner bolt | 24 +/- 3 N.m (17 +/- 2 ft-lb) |
| Camshaft sprocket bolt | 88 +/- 10 N.m (65 +/- 7 ft-lb) |
| Counterbalance shaft sprocket bolt | 45 +/- 3 N.m (33 +/- 2 ft-lb) |
| Crankshaft bolt | 162 +/- 5 N.m (119 +/- 4 ft-lb) |
| Crankshaft position sensor bolt | 8.8 +/- 1 N.m (78 +/- 9 in-lb) |
| Engine support bracket bolt and nut | 49 +/- 5 N.m (36 +/- 4 ft-lb) |
| Idler pulley bolt | 44 +/- 5 N.m (33 +/- 4 ft-lb) |
| Oil pump sprocket nut | 35 +/- 6 N.m (26 +/- 4 ft-lb) |
| Power steering pump bolt | 49 +/- 5 N.m (36 +/- 4 ft-lb) |
| Tensioner arm bolt | 22 +/- 4 N.m (16 +/- 3 ft-lb) |
| Tensioner B bolt | 19 +/- 3 N.m (14 +/- 2 ft-lb) |
| Tensioner pulley bolt | 48 +/- 6 N.m (35 +/- 4 ft-lb) |
| Timing belt cover flange bolt M6 | 11 +/- 1 N.m (95 +/- 9 in-lb) |
| Timing belt cover flange bolt M8 | 14 +/- 1 N.m (122 +/- 9 in-lb) |
| Timing belt cover washer assembled bolt | 8.8 +/- 1 N.m (78 +/- 9 in-lb) |
| Fuel and emission control parts | |
| EGR valve bolt | 19 +/- 3 N.m (14 +/- 2 ft-lb) |
| Fuel pressure regulator bolt | 8.8 +/- 2 N.m (78 +/- 17 in-lb) |
| Injectors and fuel rail bolt | 12 +/- 1 N.m (104 +/- 9 in-lb) |
| Throttle body bolt | 19 +/- 3 N.m (14 +/- 2 ft-lb) |
| Throttle body stay bolt | 19 +/- 3 N.m (14 +/- 2 ft-lb) |
| Water pump and intake manifold | |
| Engine coolant temperature gauge unit | 11 +/- 1 N.m (95 +/- 9 in-lb) |
| Engine coolant temperature sensor | 29 +/- 10 N.m (22 +/- 7 ft-lb) |
| Engine hanger bolt | 19 +/- 3 N.m (14 +/- 2 ft-lb) |
FASTENER TIGHTENING SPECIFICATIONS (2 OF 3)
| ITEMS | SPECIFICATION |
|---|---|
| Intake manifold plenum bolt and nut | 20 +/- 2 N.m (14 +/- 1 ft-lb) |
| Intake manifold plenum stay M8 | 21 +/- 4 N.m (15 +/- 3 ft-lb) |
| Intake manifold plenum stay M10 | 30 +/- 3 N.m (22 +/- 2 ft-lb) |
| Manifold differential pressure sensor bolt | 4.9 +/- 1 N.m (43 +/- 9 in-lb) |
| Oil dipstick guide bolt | 14 +/- 1 N.m (122 +/- 9 in-lb) |
| Thermostat housing bolt | 24 +/- 4 N.m (17 +/- 3 ft-lb) |
| Water inlet fitting bolt | 13 +/- 2 N.m (113 +/- 17 in-lb) |
| Water inlet pipe bolt | 13 +/- 2 N.m (113 +/- 17 in-lb) |
| Water pump bolt | 14 +/- 1 N.m (122 +/- 9 in-lb) |
| Exhaust manifold | |
| Exhaust manifold bracket bolt | 35 +/- 6 N.m (26 +/- 4 ft-lb) |
| Exhaust manifold cover bolt | 14 +/- 1 N.m (122 +/- 9 in-lb) |
| Exhaust manifold nut M8 | 29 +/- 3 N.m (22 +/- 2 ft-lb) |
| Exhaust manifold nut M10 | 49 +/- 5 N.m (36 +/- 4 ft-lb) |
| Heat protector bolt | 14 +/- 1 N.m (122 +/- 9 in-lb) |
| Oxygen sensor | 44 +/- 5 N.m (32 +/- 4 ft-lb) |
| Water outlet fitting bolt | 13 +/- 2 N.m (113 +/- 17 in-lb) |
| Rocker arms and camshaft | |
| PCV valve | 10 +/- 2 N.m (87 +/- 17 in-lb) |
| Rocker cover bolt | 3.5 +/- 0.5 N.m (30 +/- 4 in-lb) |
| Rocker arm shaft bolt | 31 +/- 3 N.m (23 +/- 2 ft-lb) |
| Cylinder head and valve | |
| Cylinder head bolt [Tighten to 78 N.m (58 ft-lb) and then completely before tightening to final torque specification] | 25 N.m (14 ft-lb) + 90° + 90° |
| Front case, counterbalance shaft and oil pan | |
| Drain plug | 39 +/- 5 N.m (29 +/- 4 ft-lb) |
| Flange bolt | 36 +/- 3 N.m (27 +/- 2 ft-lb) |
| Front case bolt | 24 +/- 3 N.m (17 +/- 2 ft-lb) |
| Oil filter part number MD360935 | 14 +/- 2 N.m (122 +/- 17 in-lb) |
| Oil filter other than MITSUBISHI genuine filter | 17 +/- 2 N.m (13 +/- 1 ft-lb) |
| Oil filter bracket bolt | 19 +/- 3 N.m (14 +/- 2 ft-lb) |
| Oil pan bolt | 6.9 +/- 1 N.m (61 +/- 9 in-lb) |
| Oil pressure switch | 11 +/- 1 N.m (95 +/- 9 in-lb) |
| Oil pump cover bolt | 17 +/- 1 N.m (12 +/- 1 ft-lb) |
| Oil pump cover screw | 9.8 +/- 2 N.m (87 +/- 17 in-lb) |
| Oil screen bolt | 19 +/- 3 N.m (14 +/- 3 ft-lb) |
| Plug | 24 +/- 3 N.m (17 +/- 3 ft-lb) |
| Relief plug | 44 +/- 5 N.m (33 +/- 4 ft-lb) |
| Piston and connecting rod | |
| Connecting rod cap nut | 20 +/- 2 N.m (14 +/- 1 ft-lb) + 90° to 94° |
FASTENER TIGHTENING SPECIFICATIONS (3 OF 3)
| ITEMS | SPECIFICATION |
|---|---|
| Crankshaft and cylinder block | |
| Bearing cap bolt | 25 +/- 2 N.m (18 +/- 1 ft-lb) + 90° |
| Bell housing cover bolt | 8.8 +/- 1 N.m (78 +/- 9 in-lb) |
| Drive plate bolt | 132 +/- 5 N.m (98 +/- 4 ft-lb) |
| Flywheel bolt | 132 +/- 5 N.m (98 +/- 4 ft-lb) |
| Knock sensor | 23 +/- 2 N.m (17 +/- 1 ft-lb) |
| Oil seal case bolt | 11 +/- 1 N.m (95 +/- 9 in-lb) |
| Rear plate bolt | 11 +/- 1 N.m (95 +/- 9 in-lb) |