31 33 005 Replacing Front Left Or Right Spring Strut Support Bearing

WARNING: This page is about a different car, the 2010 BMW X5, 2009 BMW X5, 2008 BMW X5, and 2007 BMW X5. However, it is still accessible from the selected car via links, so may be relevant.

Special tools required:

31 3 341
31 3 351
31 3 353

WARNING: Observe the following instructions to avoid any risk of injury by the coil springs.

Prior to each use, check the special tools for defects, modifications and operational reliability.
Damaged/modified special tools must not be used!
No changes or modifications may be made to the special tools!
These special tools are intended solely for the purpose of tightening and relieving cylindrical and tapered suspension springs.
Keep special tools dry, clean and free of grease.
Impact screwdrivers may not be used!
Do not compress coil spring to full extent.
Observe manufacturer's instructions.

Version with Vertical Dynamics Management:

IMPORTANT: Handle the spring strut with care so as to avoid damaging the control unit (1) and control valve (2).

Fig 1: Identifying Control Unit And Control Valve

Courtesy of BMW OF NORTH AMERICA, INC.

Necessary preliminary tasks:

Remove front spring strut . See 31 31 000 REMOVING AND INSTALLING COMPLETE LEFT OR RIGHT SPRING STRUT SHOCK ABSORBER .

Removing:

Clamp special tool 31 3 341 in vice.

Fit special tools 31 3 351 and 31 3 353 from above on special tool 31 3 341 until locking pins (1) can be felt and heard to snap into place.

Check seating of special tools 31 3 351 and 31 3 353 , correct if necessary.

Fig 2: Identifying Locking Pin And Special Tool (31 3 351)

Courtesy of BMW OF NORTH AMERICA, INC.

Clean coil spring to remove coarse contamination and take up with special tools 31 3 351 and 31 3 353 .

Turn spring strut until end of coil spring (1) points upwards.

Fig 3: Identifying Coil Spring And Special Tool (31 3 353)

Courtesy of BMW OF NORTH AMERICA, INC.

WARNING: Coils of coil spring must be located completely in recesses of special tools 31 3 351 and 31 3 353 when tensioned!

Compress coil spring until stress on piston rod is relieved.

Fig 4: Identifying Special Tool (31 3 351) (31 3 353)

Courtesy of BMW OF NORTH AMERICA, INC.

Unscrew nut (1).

Remove joint disc (2), support bearing upper section (3) and support bearing flange (4).

Fig 5: Identifying Joint Disc, Support Bearing Upper Section, Support Bearing Flange And Nut

Courtesy of BMW OF NORTH AMERICA, INC.

Assembly:

Replace support bearing lower section (2), support bearing upper section (4) and support bearing flange (5).

Check upper spring pad (1) and protective tube (3) for damage, replace if necessary.

NOTE: Align upper spring pad (1) by means of coding to support bearing flange (5).

Fig 6: Identifying Upper Spring Pad And Support Bearing Flange

Courtesy of BMW OF NORTH AMERICA, INC.

Version with Vertical Dynamics Management:

IMPORTANT: For spring strut installation, it is essential that the stud bolt (1) and positioning pin (2) are flush with each other!

Fig 7: Identifying Stud Bolt And Positioning Pin

Courtesy of BMW OF NORTH AMERICA, INC.

Attach support bearing flange (1) to piston rod.

Align support bearing upper section (3) as illustrated and attach to inner section (2) of support bearing flange (1).

NOTE: Pay attention to edge (4) in shown in illustration.

Fig 8: Identifying Bearing Flange, Inner Section And Edge

Courtesy of BMW OF NORTH AMERICA, INC.

Attach joint disc (1) to piston rod.

Replace nut (2), screw onto piston rod and tighten down.

Tightening torque. See FRONT AXLE - TIGHTENING TORQUES .

Fig 9: Identifying Joint Disc And Nut

Courtesy of BMW OF NORTH AMERICA, INC.

Align support bearing flange (1) and spring strut (3) by means of spring pads to coil spring ends.

Relieve tension on coil spring.

Check installation position of protective tube (2), correct if necessary.

NOTE: Make sure upper and lower coils of coil spring rest correctly against support bearing flange or spring plate.

Fig 10: Identifying Support Bearing Flange, Spring Strut And Protective Tube

Courtesy of BMW OF NORTH AMERICA, INC.