Torque Specifications
WARNING: This page is about a different variant/trim than selected.
TORQUE SPECIFICATIONS
| Description | N.m | lb-ft | lb-in |
|---|---|---|---|
| Hose clamps | 4 | - | 35 |
| Intake system | - | - | - |
| Intake manifold studs | 10 | - | 89 |
| Intake manifold bolts and nuts | 18 | 13 | - |
| Engine lifting eye with coolant hose brackets | 18 | 13 | - |
| Oil lever indicator tube | 10 | - | 89 |
| Throttle body | 10 | - | 89 |
| Heat shield to cylinder head (M6) | 10 | - | 89 |
| Heat shield to cylinder head and exhaust manifold (M8) | 16 | 12 | - |
| Exhaust manifold studs | 10 | - | 89 |
| Exhaust manifold nuts | 16 | 12 | - |
| Catalytic converter to exhaust manifold | 41 | 30 | - |
| Catalytic converter to exhaust | 45 | 33 | - |
| Catalytic converter bracket bolt | 25 | 18 | - |
| Right-hand front axle driveshaft center bearing | 27 | 20 | - |
| Front axle driveshaft bracket to engine | 48 | 35 | - |
| Generator to bracket | 25 | 18 | - |
| Generator bracket to cylinder block | 65 | 48 | - |
| Automatic transaxle flange bolts | 48 | 35 | - |
| Manual transaxle flange bolts | 40 | 30 | - |
| Starter motor to transmission | 48 | 35 | - |
| Transaxle oil drain plug | 27 | 20 | - |
| Transaxle oil check plug | 35 | 26 | - |
| Automatic transmission fluid cooler lines | 23 | 17 | - |
| Flywheel/drive plate | 112 | 83 | - |
| Clutch pressure plate | 29 | 21 | - |
| Subframe to body | 130 | 96 | - |
| Steering gear to subframe | 130 | 96 | - |
| Radiator bracket to subframe | 10 | - | 89 |
| Air conditioning compressor to bracket | 25 | 18 | - |
| Air conditioning condenser to subframe | 11 | 8 | - |
| Right-hand engine support insulator to transaxle | 84 | 62 | - |
| Right-hand engine support insulator to subframe | 48 | 35 | - |
| Right-hand engine support insulator bracket to transaxle (MTX 75) | 84 | 62 | - |
| Left-hand engine support insulator bracket to transaxle (MTX 75) | 84 | 62 | - |
| Center bolt-left and right-hand support insulator | 120 | 89 | - |
| Rear engine mounting to transaxle | 83 | 61 | - |
| Front engine mounting bracket to engine and engine mounting | 83 | 61 | - |
| Hub nut | 290 | 214 | - |
| Wheel nuts | 128 | 94 | - |
| Suspension strut to body | 46 | 34 | - |
| Lower suspension arm ball joint to wheel knuckle | 83 | 61 | - |
| Tie rod to wheel knuckle | 26 | 19 | - |
| Stabilizer link rod to suspension strut | 47 | 35 | - |
| Power steering pump to bracket | 47 | 35 | - |
| Air conditioning compressor bracket/power steering pump to cylinder block | 47 | 35 | - |
| Steering gear heat shield | 24 | 18 | - |
| Steering gear to subframe | 130 | 96 | - |
| VCT oil feed flange to cylinder head | 10 | - | 89 |
| Camshaft position sensor to cylinder head | 9 | - | 80 |
| Cylinder head bolts (Stage 1) | 20 | 15 | - |
| Cylinder head bolts (Stage 2) | 40 | 30 | - |
| Cylinder head bolts (Stage 3) | 90 degrees | 90 degrees | - |
| Appearance cover | 7 | - | 62 |
| Camshaft bearing caps | 15 | 11 | - |
| Valve cover (Stage 1) | 2 | - | 18 |
| Valve cover (Stage 2) | 7 | - | 62 |
| Spark plugs | 15 | 11 | - |
| Retaining pin for timing belt tensioner spring | 10 | - | 89 |
| Timing belt tensioner | 25 | 18 | - |
| Intake camshaft timing pulley | 68 | 50 | - |
| Exhaust camshaft timing pulley (Stage 1) | 60 | 44 | - |
| Exhaust camshaft timing pulley (Stage 2) | 120 | 89 | - |
| Exhaust camshaft timing pulley blanking plug | 37 | 27 | - |
| Upper engine front cover | 10 | - | 89 |
| Lower engine front cover | 8 | - | 71 |
| Blanking plug, cylinder head oil channel | 15 | 11 | - |
| EI ignition coil bracket to cylinder head | 21 | 15 | - |
| Electronic power steering pump mounting plate to cylinder head | 47 | 35 | - |
| Thermostat housing | 20 | 15 | - |
| Engine lifting eye to cylinder head | 16 | 12 | - |
| Engine lifting eye to generator bracket | 47 | 35 | - |
| Engine oil drain plug | 25 | 18 | - |
| Oil pressure switch | 27 | 20 | - |
| Blanking plugs, cylinder block oil channels | 25 | 18 | - |
| Heater pipe bracket to oil pan | 10 | - | 89 |
| Oil pan to lower crankcase | 24 | 18 | - |
| Lower crankcase to cylinder block | 30 | 22 | - |
| Lower crankcase to upper crankcase bolts | 22 | 16 | - |
| Lower crankcase to transmission bolts | 40 | 30 | - |
| AC bracket bolts | 25 | 18 | - |
| Oil pump | 11 | 8 | - |
| Oil intake pipe to oil pump | 10 | - | 89 |
| Main bearing cap bolts | 85 | 63 | - |
| Connecting rod bearing cap bolts (Stage 1) | 35 | 26 | - |
| Connecting rod bearing cap bolts (Stage 2) | 90 degrees | 90 degrees | - |
| Coolant pump | 18 | 13 | - |
| Crankshaft rear oil seal carrier | 30 | 22 | - |
| Drive belt idler pulley | 40 | 30 | - |
| Crankcase ventilation tube to cylinder block | 10 | - | 89 |
| Crankcase ventilation to cylinder bloc k | 10 | - | 89 |
| Coolant pump belt pulley | 24 | 18 | - |
| Crankshaft belt pulley | 115 | 85 | - |
| Crankshaft position sensor bracket to cylinder block | 21 | 15 | - |
| Crankshaft position sensor to bracket | 8 | - | 71 |
| Upper idler roller bearing | 38 | 28 | - |
| Lower idler roller bearing | 38 | 28 | - |