Remove/Install Spring Bracket Of Rear Axle Spring - Ar61.25-D-6155TSC

Model 907.6/7 with code IR2 (Wheelbase 3250 mm) 

Shown on model 907.6 with code IR2 (wheelbase 3,250 mm), left side of vehicle 

	Risk of death  when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)	Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines
	Risk of death  caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
	The high voltage used for electric welding presents a lethal hazard. Risk of explosion  from welding in areas close to highly inflammable materials. Risk of injury  from weld splatter and UV-light when welding. Risk of poisoning  from inhaling welding gases	Use insulating mats. Wear protective clothing, safety glasses and a protective mask. Remove highly inflammable materials from the hazard area. Use air extraction system.	AS00.00-Z-0007-01A
	Risk of injury  caused by scraping or cutting body parts on sharp vehicle parts	Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels.	AS00.00-Z-0017-01A
	Measures for preventing damage to vehicles or components when performing electric welding work		AH00.00-N-0005-01A
	General information on body repair		AH60.00-N-0001-01A
	Remove
1	Remove all detachable parts in area of repair point.
2	Cover detachable parts that remain in vehicle with welding protection blankets.	Commercially available devices/tools  Welding protection blanket
3	Remove the lower rear side wall paneling behind the wheel arch.		AR63.10-D-5667-01TS
		Commercially available devices/tools  Body power jigsaw Rotary wire brush Spot weld milling machine Wet and dry vacuum cleaner
		1K-zinc dust paint	*BR00.45-Z-1056-07A
4	Remove the outer lower section of the corner pillar paneling.		AR64.30-D-5705-05TS
		Commercially available devices/tools  Body power jigsaw Spot weld milling machine Straight grinder Rotary wire brush Wet and dry vacuum cleaner
		1K-zinc dust paint	*BR00.45-Z-1056-07A
5	Remove the D-pillar reinforcement behind the	lower corner pillar paneling.	AR64.30-D-0003-01TS
	000 588 00 84 00 Heat gun		WS54.00-P-0049B
		Commercially available devices/tools  Body power jigsaw Spot weld milling machine Rotary wire brush Wet and dry vacuum cleaner
		1K-zinc dust paint	*BR00.45-Z-1056-07A
6	Remove the spring bracket (1) of the rear axle spring.		AR61.25-D-6155-01TSC
		Commercially available devices/tools  Body power jigsaw Straight grinder Spot weld milling machine Rotary wire brush Wet and dry vacuum cleaner
7	Prepare the spring bracket (1) of the rear axle spring for installation.		AR61.25-D-6155-02TSC
		Commercially available devices/tools  Rotary wire brush Wet and dry vacuum cleaner
8	Prepare the D-pillar reinforcement behind the lower corner pillar paneling for installation.		AR64.30-D-0003-02TS
		Commercially available devices/tools  Body power jigsaw Hole punching pliers 6 mm Rotary wire brush Wet and dry vacuum cleaner
		1K-zinc dust paint	*BR00.45-Z-1056-07A
9	Prepare the lower section of the outer corner pillar paneling for installation.		AR64.30-D-5705-06TS
		Commercially available devices/tools  Body power jigsaw Hole punching pliers 6 mm Rotary wire brush Wet and dry vacuum cleaner
		1K-zinc dust paint	*BR00.45-Z-1056-07A
10	Prepare the lower rear side wall paneling behind the wheel arch for installation.		AR63.10-D-5667-02TS
		Commercially available devices/tools  Rotary wire brush Wet and dry vacuum cleaner
		1K-zinc dust paint	*BR00.45-Z-1056-07A
	Install
11	Install and weld in the spring bracket (1) of the rear axle spring.		AR61.25-D-6155-03TSC
	000 588 02 84 00 Welder		WS60.00-P-0022K
		Commercially available devices/tools  Clamping pliers (Standard) Angular grinder Wet and dry vacuum cleaner
12	Install and weld in the D-pillar reinforcement behind the lower corner pillar paneling.		AR64.30-D-0003-03TS
	000 588 01 84 00 Welder		WS60.00-P-0021K
	000 588 02 84 00 Welder		WS60.00-P-0022K
		Commercially available devices/tools  Clamping pliers (Standard) Squeeze gun Rotary wire brush Wet and dry vacuum cleaner
		Gap dimensions of rear-end door	*BE60.00-N-1007-01TS
		Black seam seal 300 ml	*BR00.45-Z-1107-01A
		Feeler gauge	Fig 1
13	Install and weld in the outer lower section of the corner pillar paneling.		AR64.30-D-5705-08TS
	000 588 01 84 00 Welder		WS60.00-P-0021K
	000 588 02 84 00 Welder		WS60.00-P-0022K
		Commercially available devices/tools  Clamping pliers (Standard) Rotary wire brush Wet and dry vacuum cleaner
14	Install and weld in the lower rear side wall paneling behind the wheel arch.		AR63.10-D-5667-03TS
	000 588 01 84 00 Welder		WS60.00-P-0021K
	000 588 02 84 00 Welder		WS60.00-P-0022K
		Commercially available devices/tools  Clamping pliers (Standard)
15	Clean weld joints and sheet metal flanges with rotary wire brush.	Commercially available devices/tools  Rotary wire brush
16	Remove welding protection blankets.	Commercially available devices/tools  Welding protection blanket
17	Clean repair area.	Commercially available devices/tools  Wet and dry vacuum cleaner
	Risk of explosion  caused by paint vapors igniting. Risk of poisoning  caused by inhaling paint vapors.	No smoking! No open fire! Use respiratory protection, protective clothing, gloves, safety glasses and protective skin cream. Ensure that the area is well ventilated.	AS98.00-Z-0002-01A
18	Prime repair area with a primer filler. Notes on paintwork repairs		AH98.00-P-9408-02A
		Use only primer filler approved by Daimler AG: http://xentryportal.mercedes-benz.com
19	Seal seam after repair.		AR97.10-D-4000TS
		Supplement standard seals with sealant.
	Risk of explosion  caused by paint vapors igniting. Risk of poisoning  caused by inhaling paint vapors.	No smoking! No open fire! Use respiratory protection, protective clothing, gloves, safety glasses and protective skin cream. Ensure that the area is well ventilated.	AS98.00-Z-0002-01A
20	Paint repair area and adjacent surfaces. Notes on paintwork repairs		AH98.00-P-9408-02A
		Use only paints approved by Daimler AG: http://xentryportal.mercedes-benz.com
21	Supplement cavity preservation		AR97.20-D-1500TS
22	Install all detachable parts in area of repair point.

Fig 1: Feeler Gauge (129 589 03 21 00)