Perform SCN Coding (Code: Vs2SCNCODM) (2017080005)
WARNING: This page is about the Sprinter 2500 Van Cargo, 2.1L Eng, which is a different variant/trim than selected.
Publication date: 2018-02-01Reference number: 2017080005
PERFORM SCN CODING (CODE: VS2SCNCODM)
SERVICE CAMPAIGN BULLETIN
Reference Number(s): 2017080005, Date of Issue:
February 01, 2018
| SPRINTER: | Model 906.134 1N up to 663754; Model 906.6## 1P as of 289479 up to 350961; Model 906.63# 1S as of 443947 up to 949592 |
SERVICE INFORMATION
Operation no. of the operation texts or standard texts and flat rates
| Category | Op. no. | Operation text | Time | Acc. no. | Code |
|---|---|---|---|---|---|
| L | 02 9950 | Operations: Connect/disconnect vehicle diagnosis system (XENTRY/DAS) | - | 54 980 57 | VS2SCNCO DM |
| L | 02 9951 | Operations: Connect/disconnect charger (with XENTRY/DAS connected) | - | 54 980 57 | VS2SCNCO DM |
| L | 02 9953 | Operations: Perform SCN coding in ATA control unit (with XENTRY/DAS connected) | - | 54 980 57 | VS2SCNCO DM |
| Check | |||
|---|---|---|---|
| 1 | Check whether vehicle is affected by measure | Affected vehicles: Perform SCN coding (code: VS2SCNCODM) For authorized Mercedes-Benz service partners, only the entry in the "Extended VEGA Application" (EVA) system, in the "Current" tab is decisive. An additional test of the affected vehicles in the workshop information system (WIS) or vehicle list is thereby not necessary. |
SM54.21-D-0122-01AAA |
| Perform SCN coding | |||
| 2 |
Mount charger A 000 588 00 81 00 Charger |
A sufficient power supply for the on-board electrical system battery must be guaranteed throughout the entire work procedure. Otherwise any undervoltage that occurs may damage the control units. Follow the operating instructions for the charger. Use the charger to ensure that an adequate voltage (min. 12.5 V) is provided for the on-board electrical system battery. |
WS54.00-P-0037B |
| 3 |
Mount diagnostic unit | Use XENTRY Diagnostics version 03/17 with all relevant updated addons (in particular addon 7550). Or XENTRY Diagnostics version 05/2017 (in particular with addon 7551) or XENTRY Diagnostics version 07/2017 (in particular with addon 7741). or a higher XENTRY Diagnostics version. The operation steps must be performed exactly as per XENTRY Diagnostics. Is XENTRY Diagnostics already connected to the vehicle. ↓ Proceed with operation step 4. |
AD00.00-D-2000-04SD |
| 4.1 |
Run SCN coding in corresponding control unit | WDB9066331S443947Except CODE XM0 (Model refinement) To do this, select the following menu items: Main groups → Control units → Information and communication → HU25 COMAND → Control unit adaptations → SCN coding → Perform SCN coding. You are automatically guided through the SCN coding procedure. |
AR54.21-D-0015X |
| 4.2 |
Run SCN coding in corresponding control unit | Model 906.1/6 with code XM0 (Facelift) To do so, select the following menu item in the "Special functions" tab: "Service measure available." The affected control unit is shown. Select the following menu item for the SCN coding procedure for the displayed control unit: Control units view → Selection of affected control unit → Adaptations → Control units update → Updating of SCN coding → You are automatically guided through the SCN coding procedure. |
AR54.21-D-0015X |
| 5 | Disconnect diagnostic unit | ||
| 6 | Remove charger |