Heat left/right outside rearview mirrors function - GF88.79-P-2000CE
MODEL 204.0/2 as of model year 2009
MODEL 204.3
MODEL 204.9
Function requirements, general
- No overvoltage or undervoltage
- On-board electrical system consumer shutoff not active
- Particular (local) front power window not active
Heat left/right outside mirror, general
The mirror heater (M21/1r1) in the left outside mirror (M21/1) and the mirror heater (M21/2r1) in the right outside mirror (M21/2) are activated in combination with the rear window heater function or depending on the outside temperature.
The left front door control unit (N69/1) directly actuates the mirror heater in the left outside mirror.
The right front door control unit (N69/2) directly actuates the mirror heater in the right outside mirror.
The heating left/right outside mirror function comprises the following partial functions:
- Function sequence for control when heated rear window is switched on
- Function sequence for temperature dependent control
Additional function requirement for control with heated rear window function switched on
- Terminal 15 ON
The electronic ignition lock control unit (N73) sends the status of circuit 15 via interior CAN (CAN B) to the front door control units.
Function sequence for control when heated rear window is switched on
With the heated rear window function active, the rear SAM control unit with fuse and relay module (N10/2) transmits the status "Heated rear window active" via interior CAN to the front door control units. The left front door control unit then directly switches on the mirror heater in the left outside mirror. The right front door control unit then directly switches on the mirror heater in the right outside mirror. The mirror heaters are actuated at 100% output as long as the request is present. When heated rear window function is switched off, the mirror heaters are also switched off.
When adjustments affecting the temperature, air distribution and air volume are made on the automatic air conditioning control and operating unit (N22/7), with the rear window heater switched on, the symbol for the rear window heater and the corresponding settings appear momentarily on the Audio/COMAND display (A40/8).
Detailed information on the heated rear window function is given in the function description "Automatic climate control, function" in the subfunction "Rear window heater, function".
Additional function requirements for temperature-dependent control
- "Engine running" or "drive train operational" signal on
The CDI control unit (N3/9) (with diesel engine) or the ME-SFI [ME] control unit (N3/10) (with gasoline engine) sends the "Engine running" or "Drive train operational" signal via chassis CAN (CAN E) to the front SAM control unit with fuse and relay module (N10/1) and via the interior CAN to the front door control units.
Function sequence for temperature dependent control
The temperature-dependent control for the mirror heater depends on the following values:
- Outside temperature
- Dewpoint temperature
The door control units compare both values with each other and switch the mirror heaters on if a dew point temperature of T = 2 °C under the outside temperature is detected.
Outside temperature:
The outside temperature is detected by the outside temperature sensor (B14). The SAM control unit directly reads in the signal of the outside temperature sensor, calculates the outside temperature and sends it to the instrument cluster (A1) over the interior CAN. The instrument cluster calculates the outside temperature to be displayed taking into account several variables and transmits the corrected outside temperature value via interior CAN to the front door control units.
If the outside temperature value received is implausible or not available, the mirror heaters are always switched on.
Dew point temperature:
The dew point temperature is the temperature at which water vapor would condense in the outside air. The glass in the mirrors would fog up.
The dew point temperature is sensed by the dew point sensor (B11/12) (up to 31.05.2010 with code (581) Comfort automatic air conditioning) or the interior humidity/temperature sensor (B82) (as of 01.12.2009). The automatic air conditioning control and operating unit reads in the signal of the corresponding sensor via climate control (LIN B8), calculates the dew point temperature and transmits it to the front door control units via the interior CAN.
If the value of the dew point is not plausible or a dew point value is not available, a substitute dew point value of T = 13 °C is used.
The following table includes information on the actuation time for the mirror heaters.
| Outside temperature | Duration of actuation | PWM output value |
|---|---|---|
| Vehicles up to 31.05.2014 | ||
| T < 15 °C | t = 10 min (once after engine start (thawing phase)) | 100 % |
| Vehicles as of 01.06.2014 | ||
| T < 15 °C | t = 10 min (once after engine start (thawing phase)) | 100 % |
| T ≤-5 °C | after thawing phase, temperature-dependent | 80 % |
| T = -5 to 5 °C | after thawing phase, temperature-dependent | 50 % |
| T = 5 to 15 °C | after thawing phase, temperature-dependent | 20 % |
The mirror heaters are switched off if:
- Outside temperature dew point +5 °C (programmable via diagnosis tester)
- Outside temperature > 18 °C=
| Electrical function diagram for mirror heater | PE88.79-P-2055-97FAB |
| Overview of system components for electric mirror | GF88.79-P-9996CE |