Status indicator, location/function - GF82.95-P-2002A
MODEL 129, 202, 208.3, 210 as of 1.6.98, 215, 220 with CODE (347) TELE AID emergency call system (D2B)
MODEL 140, 210 up to 31.5.98 with CODE (348) TELE AID emergency call system
MODEL 140, 202, 210, 220 with CODE (930) Taxi emergency call
The status indicator in the TELE AID pushbutton switch (S93/3) serves for checking the function of the TELE AID system.
Every time the TELE AID system is switched on the status indicator comes on for approx. 4 s and signals the readiness of TELE AID for an emergency call. Then the status indicator goes out.
If a TELE AID emergency call (not with taxi emergency call) is triggered the status indicator starts flashing (0.5 s on, 0.5 s off, ...). If it was not possible to transmit a TELE AID emergency call (data and voice) nor a 112 emergency call the status indicator comes on. If a voice connection is completed the status indicator returns to the same status as before the emergency call actuation.
If the TELE AID system is in the diagnosis mode the status indicator also starts flashing.
A TELE AID system error is present when the status indicator does not go out 5 s after switching on or when it comes on at a later time.
Permanent illumination of the status indicator can have the following causes:
External error
- Power supply too low
- No or incorrect SIM card installed
- Communication with emergency tensioning retractor control module with airbag (AB) (N2/2, except models 215, 220) or restraint system control module (N2/7, models 215, 220) interrupted
- Communication with traction system control module (N47) interfered
- Malfunction of emergency call pushbutton switch (S93/3)
- Error of emergency alarm actuation switch (S62/6) (only with code 930, taxi emergency call)
- Error of GPS reception (antenna system)
The telephone antenna
depends on the model
Model 129: rod antenna (A28)
Models 202, 208.3, 210, 220: telephone antenna (A2/49a1)
Model 215: telephone antenna (A2/22)
- No reception over TELE AID substitute antenna (A2/50) or telephone antenna (A2/49a1)
- CTEL transmitter and receiver (A35) or connection to emergency call system control module (TELE AID, A35/8) erroneous
Internal error
- Vehicle is not authorized or is in the progress of authorization
- Memory defect on emergency call system control module (TELE AID, A35/8)
- Rollover sensor (B66) defective
- GPS reception erroneous
- The PIN (P ersonal I dentification N umber) has not been stored in the emergency call system control module (TELE AID, A35/8) by the user (e.g. after changing PIN number)
The emergency call system control module (TELE AID, A35/8) can be coded with the hand-held tester so that the status indicator does not come on even when the system is not authorized (however, all further system errors are indicated).
| Emergency call actuation, function | GF82.95-P-2003A | ||
| TELE AID switch-on/switch-off characteristics, function | GF82.95-P-2000A | ||
| Authorization, function | GF82.95-P-2001A | ||
| PIN check with TELE AID emergency call, function | GF82.95-P-3002A | ||
| Data from airbag control module for TELE AID, function | GF82.95-P-3003A | ||
| TELE AID control module, location/purpose/ design/function | GF82.95-P-4100A | ||
| TELE AID emergency call pushbutton switch, location/purpose/design/function | GF82.95-P-4101A | ||
| Rod antenna, location/purpose | Model 129 | GF82.62-P-4115B | |
| Telephone antenna, location/purpose | Model 215 | GF82.62-P-4105B | |
| GPS/telephone roof antenna, location/purpose/design/function | Models 140, 202, 208.3, 210, 220 with code 351, 815, 347, 348 | GF82.70-P-4111A | |
| GPS/telephone/radio roof antenna, location/purpose/design/function | Model 140 except 140.063/07, 202, 210, 220 with code 930 | GF82.70-P-4112A | |
| TELE AID substitute antenna, location/purpose/design/function | GF82.95-P-4102A |