Status display position/function - GF82.95-P-2002P
MODEL 203, 210, 220 with CODE (855) TELE AID with CODE (930) Taxi emergency call for TELE AID emergency call
MODEL 208.3, 215 with CODE (855) TELE AID for TELE AID emergency call
The status indicator in the TELE AID push-button switch (S93/3) serves for checking the function of the TELE AID system.
Every time the TELE AID system is switched on the status indicator comes on for approx. 4 s and signals the readiness for TELE AID for an emergency call. Then the status indicator goes out.
If an TELE AID emergency call (not on taxi emergency call code 930) is triggered the status indicator starts flashing (0.5 s on, 0.5 s off, ...) and a message appears in the instrument cluster. If it was not possible to transmit a TELE AID emergency call (data and voice) and no 112 emergency call the status indicator comes on and a message appears on the display of the instrument cluster. If a voice connection is completed the status indicator returns the same status as before the emergency call actuation and a message appears on the instrument cluster display.
If the TELE AID system is in the diagnosis mode the status indicator also starts flashing.
A TELE AID system error is present when the status indicator does not go out 5 s after switching on or when it comes on at a later time. A message then appears in the instrument cluster display.
Permanent illumination of the status indicator can have the following causes:
External error
- Rollover sensor (B66) defective
- Power supply too low
- No or incorrect SIM card installed
- Communication with restraint system control module (N2/7) interrupted
- Communication with traction system control module (N47) interfered
- Error on TELE AID push-button switch (S93/3)
- Error on emergency alarm actuation switch (S62/6) (only with code 930, taxi emergency call)
- Error on GPS reception (antenna system)
- No reception over TELE AID substitute antenna (A2/50) or telephone antenna (A2/22, A2/49a1
Internal error
- GPS reception erroneous
- Vehicle is not authorized or is in the progress of authorization
- Memory defect on telephone transmitter/receiver and TELE AID, D2B (A35/17)
- The PIN (P ersonal I dentification N umber) is not stored in the telephone transmitter/receiver and TELE AID, D2B (A35/17) by the user (e.g. after changing PIN number)
- Telephone transmitter/receiver unit integrated in telephone transmitter/receiver and TELE AID, D2B (A35/17) erroneous
The telephone transmitter/receiver and TELE AID, D2B (A35/17) can be coded with STAR diagnosis so that the status indicator does not come on even when the system is not authorized (all other system errors are indicated).
The dealer should have the customer confirm deactivation the status indicator using a preprinted form.
| TELE AID switch-on/switch-off characteristics, function | GF82.95-P-2000P | ||
| Authorization, function | GF82.95-P-2001P | ||
| Emergency call actuation function | GF82.95-P-2003P | ||
| PIN check with TELE AID emergency call, function | GF82.95-P-3002P | ||
| Restraint system control module data, function | GF82.95-P-3005P | ||
| Transmitter/receiver unit, location/purpose/ design/function | for telephone and TELE AID | GF82.95-P-4300A | |
| TELE AID push-button switch, location/purpose/design/function | GF82.95-P-4101A | ||
| Telephone antenna, location/purpose | GF82.62-P-4105P | ||
| TELE AID substitute antenna, location/purpose/design/function | GF82.95-P-4102P | ||
| Rollover sensor, location/purpose | GF82.95-P-4206P |