Automatic Transmission - Testing & Repair - 210 Chassis
- Testing & Repair
- Checking oil level in automatic transmission and correcting, if necessary - AR27.00-P-0100A
- Inspect ATF level in automatic transmission, add ATF if necessary - AR27.00-P-0101A
- Disconnecting and connecting plug connector - AR27.10-P-0500-01A
- Remove/install oil filler pipe - AR27.10-P-0500-04A
- Removal and installation of transmission with torque converter - AR27.10-P-0500A
- Remove/install transmission with torque converter - AR27.10-P-0500B
- Fasten transmission to assembly stand Support plate for mounting transmission - AR27.10-P-0600-01B
- Insert selector valve into driver of detent plate - AR27.19-P-0200-01A
- Remove/install electrohydraulic controller unit (transmission installed) - AR27.19-P-0200A
- Disassemble and assemble electrohydraulic control unit - AR27.19-P-0220A
- Removing and installing torque converter - AR27.20-P-0500-01A
- Remove/install torque converter - AR27.20-P-0500-01B
- Flushing out oil cooler with oil cooler pipe and torque converter - AR27.20-P-0500-02A
- Checking torque converter - AR27.20-P-0500-03A
- Dismantle and assemble shift plate - AR27.35-P-0350A
- Screw on and secure twelve-point collared nut and secure - AR27.50-P-0600-04B
- Install grooved ball bearing in rear transmission housing - AR27.50-P-0600-05A
- Measure end play between park pawl gear and grooved ball bearing - AR27.50-P-0600-06A
- Remove grooved ball bearing in rear of transmission housing - AR27.50-P-0601-01A
- Detach/attach transmission housing on torque converter housing. - AR27.50-P-0601A
- Removing and installing multiple-disc clutches K1, K2 and K3 - AR27.50-P-0621A
- Dismantling and assembling oil pump - AR27.50-P-0720-01A
- Removal of brake band B2 - AR27.50-P-0780-03A
- Inserting and measuring multiple-disc pack B3 - AR27.50-P-0780-11A
- Removing and installing multi-disk brake B2, disk pack B3 and park pawl gear - AR27.50-P-0781A
- Checking and adjusting end play between shim and circlip - AR27.50-P-0810-01A
- Dismantling and assembling output shaft with center and rear gear set - AR27.50-P-0810A
- Disassembling and assembling rear hollow shaft with rear freewheel - AR27.50-P-0850A
- Inserting and measuring multi-disk pack B1 Thickness steel multi-disks B1, K1 and K2 changed - AR27.50-P-0870-01A
- Dismantling and assembling multi-disk brake B1 - AR27.50-P-0870A
- Assembling piston guide and outer multiple-disc carrier of multiple-disc brake - AR27.50-P-0880-01A
- Inserting and measuring multiple-disc pack B2 - AR27.50-P-0880-02A
- Dismantling and assembling multiple-disc brake B2 - AR27.50-P-0880A
- Insert and measure multi-disk pack K1 Thickness of steel multi-disks B1, K1 and K2 changed - AR27.51-P-0800-02A
- Insert and measure multi-disk pack K1 - AR27.51-P-0800-02AA
- Disassemble/assemble clutch K1 - AR27.51-P-0800B
- Inserting and measuring multiple-disc pack K2 Thickness of steel discs B1, K1 and K2 revised Additional disc spring in multiple-disc pack K2 - AR27.51-P-0820-02A
- Dismantling and assembling drive shaft with clutch K2 and front gear set - AR27.51-P-0825A
- Inserting and measuring multi-disk pack K3 Thickness of friction and steel multi-disks K3 changed - AR27.51-P-0830-01A
- Inserting and measuring multiple-disc pack K3 - AR27.51-P-0830-01AA
- Disassemble and assemble clutch K3. - AR27.51-P-0830A
- Flush out oil cooler lines and oil cooler - AR27.55-P-0001A
- Removing and installing automatic transmission oil cooler - AR27.55-P-1000A
- Removing and installing ignition lock control cable - AR27.60-P-0122F
- Removing and installing wire cable/transmission for parking lock interlock on transmission - AR27.60-P-0500-05A
- Removing and installing wire cable / transmission for parking shift lock on transmission - AR27.60-P-0500-05B
- Remove/install floor selector - AR27.60-P-0900B
- Removing and installing electronic selector lever module (ESM) - AR27.60-P-0901B
- Adjust shift lock - AR27.60-P-0910A
- Removing and installing selector lever handle - AR27.60-P-0920-01A
- Disassembling and assembling floor shift - AR27.60-P-0920B
- Adjusting wire cables for parking lock interlock - AR27.60-P-0965A
- Adjusting wire cables for parking lock interlock - AR27.60-P-0965B
- Adjusting shift rod - AR27.60-P-0980B
- Adjusting shift rod - AR27.60-P-0980C
- Removing and installing wire cable for parking lock interlock - AR27.60-P-1000B