LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2025 >> CX-5 S Select >> Repair and Diagnosis >> External Pages >> Different car >> Section 15 (On-Board Diagnostic - Body Control Module (BCM) (3 Of 4)) >> PID/Data Monitor Table

PID/Data Monitor Table

WARNING: This page is about a different car, the 2024 Mazda CX-30. However, it is still accessible from the selected car via links, so may be relevant.

-: Not applicable

PID/DATA MONITOR (BCM)

PID Unit/Operation Data contents
7GTURN_APPLIED_STAT Off/On
  • Off: Turn light request signal is not received.
  • On: Turn light request signal is received.
ACC_RLY Off/On
  • Off: ACC relay drive is off.
  • On: ACC relay drive is on.
ADAS_HZRD_REQ NoRequest/RequestControl
  • NoRequest: Hazard warning light flashing request signal is not received.
  • RequestControl: Hazard warning light flashing request signal is received.
ADAS_TURN_REQ NoRequest/RequestControl
  • NoRequest: Turn light request signal is not received.
  • RequestControl: Turn light request signal is received.
AGS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: AGS is not equipped.
  • Node Attached and Communicate correctly: AGS is equipped, communication with AGS is normal.
  • NodeAttached but Not Communicate correctly: AGS is equipped, but communication with AGS is not normal.
AIR_INTAKE_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Air intake actuator is not equipped.
  • Node Attached and Communicate correctly: Air intake actuator is equipped, communication with air intake actuator is normal.
  • NodeAttached but Not Communicate correctly: Air intake actuator is equipped, but communication with air intake actuator is not normal.
ALH_HBC_SW Off/On
  • Off: High beam control switch/Adaptive LED headlight switch is off.
  • On: High beam control switch/Adaptive LED headlight switch is on.
ALH_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Auto leveling control module/adaptive LED headlights control module/adaptive front lighting system (AFS) control module is not equipped.
  • Node Attached and Communicate correctly: Auto leveling control module/adaptive LED headlights control module/adaptive front lighting system (AFS) control module is equipped, communication with auto leveling control module/adaptive LED headlights control module/adaptive front lighting system (AFS) control module is normal.
  • NodeAttached but Not Communicate correctly: Auto leveling control module/adaptive LED headlights control module/adaptive front lighting system (AFS) control module is equipped, but communication with auto leveling control module/adaptive LED headlights control module/adaptive front lighting system (AFS) control module is not normal.
AMB_TEMP °C, °F Displays ambient temperature
AMP_CAN_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Audio amplifier is not equipped.
  • Node Attached and Communicate correctly: Audio amplifier is equipped, CAN communication with audio amplifier is normal.
  • NodeAttached but Not Communicate correctly: Audio amplifier is equipped, but CAN communication with audio amplifier is not normal.
AMP_MOST_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Audio amplifier is not equipped.
  • Node Attached and Communicate correctly: Audio amplifier is equipped, MOST communication with audio amplifier is normal.
  • NodeAttached but Not Communicate correctly: Audio amplifier is equipped, but MOST communication with audio amplifier is not normal.
ANTI_THEFT_SYS OFF/ON
  • OFF: Advanced keyless function is off.
  • ON: Advanced keyless function is on.
APP % Accelerator pedal opening angle (relative value) with the fully released status as 0% and fully depressed status as 100%
AT_IND_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Shift position indication is not equipped.
  • Node Attached and Communicate correctly: Gear position indication/Shift position indication is equipped, communication with gear position indication/shift position indication is normal.
  • NodeAttached but Not Communicate correctly: Gear position indication/Shift position indication is equipped, but communication with gear position indication/shift position indication is not normal.
AUTO_LIGHT_OFF Off/On
  • Off: TNS (parking lights) or headlight off control by auto light off system is not operated.
  • On: TNS (parking lights) or headlight off control by auto light off system is operated.
AVAS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Approaching vehicle audible system (AVAS) device is not equipped.
  • Node Attached and Communicate correctly: Approaching vehicle audible system (AVAS) device is equipped, communication with approaching vehicle audible system (AVAS) device is normal.
  • NodeAttached but Not Communicate correctly: Approaching vehicle audible system (AVAS) device is equipped, but communication with approaching vehicle audible system (AVAS) device is not normal.
BATT_SEN_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Current sensor is not equipped.
  • Node Attached and Communicate correctly: Current sensor is equipped, communication with current sensor is normal.
  • NodeAttached but Not Communicate correctly: Current sensor is equipped, but communication with current sensor is not normal.
BATT_SOC % Battery charge condition (estimated)
BBS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Theft-deterrent siren is not equipped.
  • Node Attached and Communicate correctly: Theft-deterrent siren is equipped, communication with theft-deterrent siren is normal.
  • NodeAttached but Not Communicate correctly: Theft-deterrent siren is equipped, but communication with theft-deterrent siren is not normal.
BECM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: BECM/Mazda M Hybrid Boost battery/Mazda M Hybrid battery is not equipped.
  • Node Attached and Communicate correctly: BECM/Mazda M Hybrid Boost battery/Mazda M Hybrid battery is equipped, communication with BECM/Mazda M Hybrid Boost battery/Mazda M Hybrid battery is normal.
  • NodeAttached but Not Communicate correctly: BECM/Mazda M Hybrid Boost battery/Mazda M Hybrid battery is equipped, but communication with BECM/Mazda M Hybrid Boost battery/Mazda M Hybrid battery is not normal.
BGLR_ALRM NoRequest/RequestControl
  • NoRequest: Body control module (BCM) does not operate theft-deterrent horn.
  • RequestControl: Body control module (BCM) operates the theft-deterrent horn.
BGLR_ALRM_ANS NoRequest/RequestControl
  • NoRequest: Hazard warning light flashing answer-back signal (theft-deterrent system) is not received.
  • RequestControl: Hazard warning light flashing answer-back signal (theft-deterrent system) is received.
BGLR_ALRM_REQ NoRequest/Request
  • NoRequest: Body control module (BCM) does not operate theft-deterrent horn and hazard warning lights on.
  • Request: Body control module (BCM) operates the theft-deterrent horn and hazard warning lights on.
BGLR_BACKUP_SIREN Off/On
  • Off: Theft-deterrent siren setting is not turned on.
  • On: Theft-deterrent siren setting is turned on.
BGLR_CHARGE Charge_OFF_backup_cells/Charge_On_backup_cells
  • Charge_OFF_back-up_cells: Theft-deterrent siren charging is not permitted.
  • Charge_On_back-up_cells: Theft-deterrent siren charging is permitted.
BGLR_GAIN - Displays the intruder sensor sensitivity set value
BGLR_HZRD_REQ Off/Blink 1 time/Blink 2 times/Blink 3 times
  • Off: Hazard warning lights are not operated to flash.
  • Blink 1 time: Hazard warning lights are operated to flash once.
  • Blink 2 times: Hazard warning lights are operated to flash twice.
  • Blink 3 times: Hazard warning lights are operated to flash three times.
BGLR_IMS Sensor Unset/Sensor Set
  • Sensor Unset: Detection stop signal is sent to intruder sensor.
  • Sensor Set: Detection start signal is sent to intruder sensor.
BGLR_IS_COMD Sensor Unset/Sensor Set
  • Sensor Unset: Detection stop signal is sent to inclination sensor.
  • Sensor Set: Detection start signal is sent to inclination sensor.
BGLR_SEN Off/On
  • Off: Intruder sensor setting is not turned on.
  • On: Intruder sensor setting is turned on.
BGLR_SIREN_COMD No_action/StartAudibleAlarm/StopAudibleAlarm/Ignore
  • No_action: Signal is not sent to theft-deterrent siren.
  • StartAudibleAlarm: Alarm start signal is sent to theft-deterrent siren. On: Intruder sensor setting is turned on.
  • StopAudibleAlarm: Alarm stop signal is sent to theft-deterrent siren.
  • Ignore: Normal signal is not sent to theft-deterrent siren.
BGLR_SIREN_MODE Set/Unset
  • Set: Theft-deterrent system is in stand-by mode or alert preparatory mode.
  • Unset: Theft-deterrent system is in mode other than above.
BGLR_SLEEP_MODE Enter Sleep Mode/Exit Sleep Mode
  • Enter Sleep Mode: Signal for transition to sleep mode is sent to theft-deterrent siren
  • Exit Sleep Mode: Execute signal is sent to theft-deterrent siren.
BGLR_STAT DEAD/INITIAL/PREARMING/ARMING/ARMING STAND BY/ALARM/ALARM STAND BY
  • DEAD: Ignition is in ACC or ON (engine off)/main power is in ACC or ON (READY off) and alarm cannot be activated.
  • INITIAL: Ignition is switched off/main power is switched OFF and transition to arming stand-by status is possible.
  • PRE-ARMING: Transition period to arming status.
  • ARMING: Alarm can be activated by inputting alarm trigger.
  • ARMING STAND BY: Trunk lid/liftgate is open under arming status.
  • ALARM: Alarm trigger is input and alarm is activated.
  • ALARM STAND BY: After alarm activation finished, standing by for next alarm trigger input.
B-ISG_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Integrated starter generator (ISG) is not equipped.
  • Node Attached and Communicate correctly: Integrated starter generator (ISG) is equipped, communication with integrated starter generator (ISG) is normal.
  • NodeAttached but Not Communicate correctly: Integrated starter generator (ISG) is equipped, but communication with integrated starter generator (ISG) is not normal.
BPS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Backup power supply unit is not equipped.
  • Node Attached and Communicate correctly: Backup power supply unit is equipped, communication with backup power supply unit is normal.
  • NodeAttached but Not Communicate correctly: Backup power supply unit is equipped, but communication with backup power supply unit is not normal.
BRK_SW Not Stepping/Stepping
  • Not Stepping: Brake pedal is not depressed.
  • Stepping: Brake pedal is depressed.
BRK_SW_1 Off/On
  • Off: Brake switch (No. 1 signal) is off.
  • On: Brake switch (No. 1 signal) is on.
C_DOOR_LCK_SW_D Neutral/Lock/Unlock
  • Neutral: Door lock switch (driver's side) is neither locked nor unlocked.
  • Lock: Door lock switch (driver's side) is in lock.
  • Unlock: Door lock switch (driver's side) is in unlock.
C_DOOR_LCK_SW_P Neutral/Lock/Unlock
  • Neutral: Door lock switch (passenger's side) is neither locked nor unlocked.
  • Lock: Door lock switch (passenger's side) is in lock.
  • Unlock: Door lock switch (passenger's side) is in unlock.
CBCM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Body control module (BCM) is not equipped.
  • Node Attached and Communicate correctly: Body control module (BCM) is equipped, communication with body control module (BCM) is normal.
  • NodeAttached but Not Communicate correctly: Body control module (BCM) is equipped, but communication with body control module (BCM) is not normal.
CENTER_DISP_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Center display is not equipped.
  • Node Attached and Communicate correctly: Center display is equipped, communication with center display is normal.
  • NodeAttached but Not Communicate correctly: Center display is equipped, but communication with center display is not normal.
CLTCH_INH_SW Off/On
  • Off: Starter interlock switch is off.
  • On: Starter interlock switch is on.
CMU_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Connectivity master unit (CMU) is not equipped.
  • Node Attached and Communicate correctly: Connectivity master unit (CMU) is equipped, communication with connectivity master unit (CMU) is normal.
  • NodeAttached but Not Communicate correctly: Connectivity master unit (CMU) is equipped, but communication with connectivity master unit (CMU) is not normal.
COMMANDER_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Commander switch is not equipped.
  • Node Attached and Communicate correctly: Commander switch is equipped, communication with commander switch is normal.
  • NodeAttached but Not Communicate correctly: Commander switch is equipped, but communication with commander switch is not normal.
CP_ESU_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Charge port-electrical supply unit is not equipped.
  • Node Attached and Communicate correctly: Charge port-electrical supply unit is equipped, communication with charge port-electrical supply unit is normal.
  • NodeAttached but Not Communicate correctly: Charge port-electrical supply unit is equipped, but communication with charge port-electrical supply unit is not normal.
CRASH_SIG Off/On
  • Off: Crash signal is not received.
  • On: Crash signal is received.
Dash-ESU_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Dash-electrical supply unit is not equipped.
  • Node Attached and Communicate correctly: Dash-electrical supply unit is equipped, dash-electrical supply unit is normal.
  • NodeAttached but Not Communicate correctly: Dash-electrical supply unit is equipped, but communication with dash-electrical supply unit is not normal.
DCDC_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: DC-DC converter is not equipped.
  • Node Attached and Communicate correctly: DC-DC converter is equipped, communication with DC-DC converter is normal.
  • NodeAttached but Not Communicate correctly: DC-DC converter is equipped, but communication with DC-DC converter is not normal.
DCDC_PCM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: DC-DC converter is not equipped.
  • Node Attached and Communicate correctly: DC-DC converter is equipped, communication with DC-DC converter is normal.
  • NodeAttached but Not Communicate correctly: DC-DC converter is equipped, but communication with DC-DC converter is not normal.
Door_ESU_D_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Door-electrical supply unit (driver's side) is not equipped.
  • Node Attached and Communicate correctly: Door-electrical supply unit (driver's side) is equipped, communication with door-electrical supply unit (driver's side) is normal.
  • NodeAttached but Not Communicate correctly: Door-electrical supply unit (driver's side) is equipped, but communication with door-electrical supply unit (driver's side) is not normal.
Door_ESU_P_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Door-electrical supply unit (passenger's side) is not equipped.
  • Node Attached and Communicate correctly: Door-electrical supply unit (passenger's side) is equipped, communication with door-electrical supply unit (passenger's side) is normal.
  • NodeAttached but Not Communicate correctly: Door-electrical supply unit (passenger's side) is equipped, but communication with door-electrical supply unit (passenger's side) is not normal.
DOOR_LCK_ALL Off/On
  • Off: All door lock signal is not sent from body control module (BCM).
  • On: All door lock signal is sent from body control module (BCM).
DOOR_LCK_ID_CREATE Off/On Displays door lock control ID creation status.
DOOR_SECURITY Off/On Displays door lock control security condition.
DOOR_SW_ALL Close/Open
  • Close: All doors are closed.
  • Open: Any door is open.
DOOR_SW_D Close/Open
  • Close: Front door (driver's side) is closed.
  • Open: Front door (driver's side) is open.
DOOR_SW_L/R Close/Open
  • Close: Rear door (LH) is closed.
  • Open: Rear door (LH) is open.
DOOR_SW_P Close/Open
  • Close: Front door (passenger's side) is closed.
  • Open: Front door (passenger's side) is open.
DOOR_SW_R/R Close/Open
  • Close: Rear door (RH) is closed.
  • Open: Rear door (RH) is open.
DOOR_ULCK_ALL Off/On
  • Off: All door unlock signal is not sent from body control module (BCM).
  • On: All door unlock signal is sent from body control module (BCM).
DOOR_ULCK_D Off/On
  • Off: Front door (driver's side) unlock request signal is not sent from body control module (BCM).
  • On: Front door (driver's side) unlock request signal is sent from body control module (BCM).
DRL Off/Activating as EU_DRL
  • Off: Daytime running light (DRL) is not turned on.
  • Activating as EU_DRL: Daytime running light (DRL) is turned on.
DRL_REQ Off/On
  • Off: Body control module (BCM) does not operate daytime running light (DRL) on.
  • On: Body control module (FBCM) operates the daytime running light (DRL) on.
DSC_PT_BUS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Electronically controlled brake unit/DSC HU/CM is not equipped.
  • Node Attached and Communicate correctly: Electronically controlled brake unit/DSC HU/CM is equipped, communication via CAN BUS No. 2 with electronically controlled brake unit/DSC HU/CM is normal.
  • NodeAttached but Not Communicate correctly: Electronically controlled brake unit/DSC HU/CM is equipped, but communication via CAN BUS No. 2 with electronically controlled brake unit/DSC HU/CM is not normal.
DSC_VEH_BUS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Electronically controlled brake unit/DSC HU/CM is not equipped.
  • Node Attached and Communicate correctly: Electronically controlled brake unit/DSC HU/CM is equipped, communication via CAN BUS No. 1 with electronically controlled brake unit/DSC HU/CM is normal.
  • NodeAttached but Not Communicate correctly: Electronically controlled brake unit/DSC HU/CM is equipped, but communication via CAN BUS No. 1 with electronically controlled brake unit/DSC HU/CM is not normal.
DSM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Position memory control module is not equipped.
  • Node Attached and Communicate correctly: Position memory control module is equipped, communication with position memory control module is normal.
  • NodeAttached but Not Communicate correctly: Position memory control module is equipped, but communication with position memory control module is not normal.
DVD_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: DVD/CD player is not equipped.
  • Node Attached and Communicate correctly: DVD/CD player is equipped, communication with DVD/CD player is normal.
  • NodeAttached but Not Communicate correctly: DVD/CD player is equipped, but communication with DVD/CD player is not normal.
ECL_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Selector lever is not equipped.
  • Node Attached and Communicate correctly: Selector lever is equipped, communication with selector lever is normal.
  • NodeAttached but Not Communicate correctly: Selector lever is equipped, but communication with selector lever is not normal.
ENG_RPM_VSPD_RATIO Rpm/Kph Displays engine speed
ENG_STARTER_V OLT_1 V Displays voltage at body control module (BCM) terminal (ST_RLY)
ENG_STARTER_VOLT_2 V Displays voltage at body control module (BCM) terminal (SRLY_MONITOR)
ENG_STAT Off/Ready/Cranking/Running/Stalled/Afterrun/Shutdown/Not defined Displays engine condition
EPS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Electric power steering (EPS) control module is not equipped.
  • Node Attached and Communicate correctly: Electric power steering (EPS) control module is equipped, communication with electric power steering (EPS) control module is normal.
  • NodeAttached but Not Communicate correctly: Electric power steering (EPS) control module is equipped, but communication with electric power steering (EPS) control module is not normal.
ESS_HZRD NoRequest/RequestControl
  • NoRequest: Hazard warning light request signal is not received during the emergency stop signal system (ESS) operation.
  • RequestControl: Hazard warning light request signal is received during the emergency stop signal system (ESS) operation.
ESU_CAN_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Electrical supply unit (ESU) is not equipped.
  • Node Attached and Communicate correctly: Electrical supply unit (ESU) is equipped, CAN communication with electrical supply unit (ESU) is normal.
  • NodeAttached but Not Communicate correctly: Electrical supply unit (ESU) is equipped, but CAN communication with electrical supply unit (ESU) is not normal.
ESU_LIN_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Electrical supply unit (ESU) is not equipped.
  • Node Attached and Communicate correctly: Electrical supply unit (ESU) is equipped, LIN communication with electrical supply unit (ESU) is normal.
  • NodeAttached but Not Communicate correctly: Electrical supply unit (ESU) is equipped, but LIN communication with electrical supply unit (ESU) is not normal.
EXT_T/LGT_REL_SW Off/On
  • Off: Trunk lid opener switch/liftgate opener switch is not pressed.
  • On: Trunk lid opener switch/liftgate opener switch is pressed.
F_WASH_CTRL_ALLW Wash_Allowed/Not_Allowed
  • Wash_Allowed: Use of windshield washer is permitted.
  • Not_Allowed: Use of windshield washer is not permitted.
F_WASH_SW Off/On
  • Off: Windshield washer switch is off.
  • On: Windshield washer switch is on.
F_WIP OFF/FrontWiper On Lo/FrontWiper On Hi/FrontWiperINT Auto On
  • OFF: Windshield wiper switch is in the OFF position.
  • FrontWiper On Lo: Windshield wiper switch is in the LO position.
  • FrontWiper On Hi: Windshield wiper switch is in the HI position.
  • FrontWiperINT Auto On: Windshield wiper switch is in the INT position.
F_WIP_ANG_SEN_FAIL Not_Failure/Failure
  • Not_Failure: Position sensor in the windshield wiper motor is normal.
  • Failure: Position sensor in the windshield wiper motor has a malfunction.
F_WIP_CTRL F.WiperOff/F.WiperLo/F.WiperHi
  • F.WiperOff: Windshield wipers are not operated.
  • F.WiperLo: Windshield wipers are operated at low speed.
  • F.WiperHi: Windshield wipers are operated at high speed.
F_WIP_FET_FAIL Not_Failure/Failure
  • Not_Failure: FET circuit is normal.
  • Failure: FET circuit has a malfunction.
F_WIP_INT_VOL % Displays windshield wiper INT level signal value received
F_WIP_POS Unknown/Parking_Position/Not_Parking_Position
  • Unknown: Windshield wipers position is not determined.
  • Parking_Position: Windshield wipers in park position.
  • Not_Parking_Position: Windshield wipers in position other than park.
F_WIP_REG_FAIL Not_Failure/Failure
  • Not_Failure: Windshield wiper regulator is normal.
  • Failure: Windshield wiper regulator is not normal.
F_WIP_REQ Off/Stop (ParkingPosition)/F.WiperLo/F.WiperHi/Stop (ServicePosition)/Stop (CurrentPosition)
  • Off: Body control module (BCM) does not operate windshield wipers.
  • Stop (ParkingPosition): Body control module (BCM) operates windshield wipers to the park position.
  • F.WiperLo: Body control module (BCM) operates windshield wipers at low speed.
  • F.WiperHi: Body control module (BCM) operates windshield wipers at high speed.
  • Stop (ServicePosition): Body control module (BCM) operates windshield wipers to the service position.
  • Stop (CurrentPosition): Body control module (BCM) operates windshield wipers to the current position.
F_WIP_ROT_FAIL Not_Failure/Failure
  • Not_Failure: Windshield wiper rotation direction is normal.
  • Failure: Windshield wiper rotation direction is not normal.
F_WIP_TEACH_STAT_SUB No_Sub_Status/Detect_jig_out_of_area/Unusually_Mode_Switch/DataFlash_Failure/FrontWipr_Failure
  • No_Sub_Status: Body control module (BCM) cannot receive any signal from windshield wiper arm and blade.
  • Detect_jig_out_of_area: Windshield wiper arm and blade movement is detected to be outside of specified range.
  • Unusually_Mode_Switch: Windshield wiper and washer switch is not normal.
  • DataFlash_Failure: Data is not normal.
  • FrontWipr_Failure: Windshield wipers are malfunctioning.
F_WIP_THRM_FAIL Not_Failure/Failure
  • Not_Failure: Circuit detecting windshield wiper motor temperature is normal.
  • Failure: Circuit detecting windshield wiper motor temperature is not normal.
F_WIP_TIME_FAIL Not_Failure/Failure
  • Not_Failure: Windshield wiper is operating normally.
  • Failure: Windshield wiper operating speed is extremely slow (when the Windshield wiper is operating).
F_WIP_VOLT_FAIL Not_Failure/Failure
  • Not_Failure: Circuit detecting windshield wiper motor voltage is normal.
  • Failure: Circuit detecting windshield wiper motor voltage is not normal.
FR_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Front radar sensor is not equipped.
  • Node Attached and Communicate correctly: Front radar sensor is equipped, communication with front radar sensor is normal.
  • NodeAttached but Not Communicate correctly: Front radar sensor is equipped, but communication with front radar sensor is not normal.
FSC_LGHT_REQ Off/On
  • Off: Headlight HI is turned off.
  • On: Headlight HI is turned on.
FSC_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Forward sensing camera (FSC) is not equipped.
  • Node Attached and Communicate correctly: Forward sensing camera (FSC) is equipped, communication with forward sensing camera (FSC) is normal.
  • NodeAttached but Not Communicate correctly: Forward sensing camera (FSC) is equipped, but communication with forward sensing camera (FSC) is not normal.
FSM_REQ Off/On
  • Off: TNS (parking lights) signal is not sent from body control module (BCM).
  • On: TNS (parking lights) signal is sent from body control module (BCM).
FSRL_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Front side radar sensor (LH) is not equipped.
  • Node Attached and Communicate correctly: Front side radar sensor (LH) is equipped, communication with front side radar sensor (LH) is normal.
  • NodeAttached but Not Communicate correctly: Front side radar sensor (LH) is equipped, but communication with front side radar sensor (LH) is not normal.
FSRR_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Front side radar sensor (RH) is not equipped.
  • Node Attached and Communicate correctly: Front side radar sensor (RH) is equipped, communication with front side radar sensor (RH) is normal.
  • NodeAttached but Not Communicate correctly: Front side radar sensor (RH) is equipped, but communication with front side radar sensor (RH) is not normal.
FUEL_AMOUNT L Displays fuel level detected by the fuel gauge
FUEL_GAUGE_RES_MAIN Ohm Displays fuel gauge sender unit resistance value
FUEL_GAUGE_RES_SUB Ohm Displays fuel gauge sender unit (sub) resistance value
FUEL_GAUGE_VOLT_MAIN V Displays fuel gauge sender unit voltage value
FUEL_GAUGE_VOLT_SUB V Displays fuel gauge sender unit (sub) voltage value
GLOBAL_REAL_TIME min Displays cumulative elapsed time since vehicle completion
GLOWPLUG_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Glow plug is not equipped.
  • Node Attached and Communicate correctly: Glow plug is equipped, communication with glow plug is normal.
  • NodeAttached but Not Communicate correctly: Glow plug is equipped, but communication with glow plug is not normal.
H/L_CLEAN_RLY Off/On
  • Off: Headlight cleaner relay is off.
  • On: Headlight cleaner relay is on.
H/L_HI Off/On
  • Off: Headlight HI signal is not sent from body control module (BCM).
  • On: Headlight HI signal is sent from body control module (BCM).
H/L_HI_SW Off/On
  • Off: Light switch HI signal is not received.
  • On: Light switch HI signal is received.
H/L_LO_REQ Off/On
  • Off: Body control module (BCM) does not operate the headlight LO on.
  • On: Body control module (BCM) operates the headlight LO on.
H/L_LO_SW Off/On
  • Off: Light switch LO signal is not received.
  • On: Light switch LO signal is received.
H/L_OFF_SW Off/On
  • Off: Light switch OFF signal is not received.
  • On: Light switch OFF signal is received.
H/L_PASSING_SW Off/On
  • Off: Light switch FLASH-TO-PASS signal is not received.
  • On: Light switch FLASH-TO-PASS signal is received.
HOOD_SW Close/Open
  • Close: Hood is closed.
  • Open: Hood is open.
HP_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Heat pump control unit is not equipped.
  • Node Attached and Communicate correctly: Heat pump control unit is equipped, communication with heat pump control unit is normal.
  • NodeAttached but Not Communicate correctly: Heat pump control unit is equipped, but communication with heat pump control unit is not normal.
HUD_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Active driving display is not equipped.
  • Node Attached and Communicate correctly: Active driving display is equipped, communication with active driving display is normal.
  • NodeAttached but Not Communicate correctly: Active driving display is equipped, but communication with active driving display is not normal.
HZRD_REQ NoRequest/RequestControl
  • NoRequest: Body control module (BCM) does not operate the hazard warning light on.
  • RequestControl: Body control module (BCM) operates the hazard warning light on.
HZRD_SW Off/On/Unknown
  • Off: Hazard warning switch is not pressed.
  • On: Hazard warning switch is pressed.
  • Unknown: Hazard warning switch on/off is not determined.
ICM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Instrument cluster is not equipped.
  • Node Attached and Communicate correctly: Instrument cluster is equipped, communication with instrument cluster is normal.
  • NodeAttached but Not Communicate correctly: Instrument cluster is equipped, but communication with instrument cluster is not normal.
IG_ON_TIMER Min Displays elapsed time after ignition is switched ON/main power is switched ON.
IG1_RLY Off/On
  • Off: IG1 relay drive is off.
  • On: IG1 relay drive is on.
IMMOBI_IDENTIFY FALSE/TRUE
  • FALSE: Verified remote transmitter ID programmed information does not match remote transmitter ID after steering lock is released.
  • TRUE: Verified remote transmitter ID programmed information matches remote transmitter ID after steering lock is released.
IMMOBI_OPERAT_MODE Operation Mode 1/Operation Mode 2/Operation Mode 3/Operation Mode 4/Operation Mode 5/Operation Mode 6/Operation Mode 7 Displays immobilizer system operation mode
IMS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Intruder sensor is not equipped.
  • Node Attached and Communicate correctly: Intruder sensor is equipped, communication with intruder sensor is normal.
  • NodeAttached but Not Communicate correctly: Intruder sensor is equipped, but communication with intruder sensor is not normal.
IND_ASSY_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Indicator unit is not equipped.
  • Node Attached and Communicate correctly: Indicator unit is equipped, communication with indicator unit is normal.
  • NodeAttached but Not Communicate correctly: Indicator unit is equipped, but communication with indicator unit is not normal.
IPESU_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Climate control unit is not equipped.
  • Node Attached and Communicate correctly: Climate control unit is equipped, communication with climate control unit is normal.
  • NodeAttached but Not Communicate correctly: Climate control unit is equipped, but communication with climate control unit is not normal.
ISB_AMP_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Notification and warning amplifier is not equipped.
  • Node Attached and Communicate correctly: Notification and warning amplifier is equipped, communication with notification and warning amplifier is normal.
  • NodeAttached but Not Communicate correctly: Notification and warning amplifier is equipped, but communication with notification and warning amplifier is not normal.
KEY_ANS_REQ NoRequest/RequestControl
  • NoRequest: Hazard warning light flashing answer-back signal is not received.
  • RequestControl: Hazard warning light flashing answer-back signal is received.
KEY_BUZZER Off/On
  • Off: Keyless beeper is not operated to sound.
  • On: Keyless beeper is operated to sound.
KEY_ENA Disabled/Enabled
  • Disabled: Immobilizer system is disabled.
  • Enabled: Immobilizer system is enabled.
LATCH_IP_SW Off/On
  • Off: Trunk lid opener switch (interior)/power liftgate (PLG) front switch is not pressed.
  • On: Trunk lid opener switch (interior)/power liftgate (PLG) front switch is pressed.
LCML_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Light control module (LH) is not equipped.
  • Node Attached and Communicate correctly: Light control module (LH) is equipped, communication with light control module (LH) is normal.
  • NodeAttached but Not Communicate correctly: Light control module (LH) is equipped, but communication with light control module (LH) is not normal.
LCMR_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Light control module (RH) is not equipped.
  • Node Attached and Communicate correctly: Light control module (RH) is equipped, communication with light control module (RH) is normal.
  • NodeAttached but Not Communicate correctly: Light control module (RH) is equipped, but communication with light control module (RH) is not normal.
LFU_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: LF control unit is not equipped.
  • Node Attached and Communicate correctly: LF control unit is equipped, communication with LF control unit is normal.
  • NodeAttached but Not Communicate correctly: LF control unit is equipped, but communication with LF control unit is not normal.
LLINK_SW_D Unlock/Neutral/Lock/Failure
  • Unlock: Front door lock-link switch (driver's side) is in unlock.
  • Neutral: Front door lock-link switch (driver's side) is not in lock and unlock.
  • Lock: Front door lock-link switch (driver's side) is in lock.
  • Failure: Front door lock-link switch (driver's side) has a malfunction.
LLINK_SW_P Unlock/Lock
  • Unlock: Front door lock-link switch (passenger's side) is in unlock.
  • Lock: Front door lock-link switch (passenger's side) is in lock.
LLINK_SW_R Unlock/Lock
  • Unlock: Rear door lock-link switch (LH), rear door lock-link switch (RH) are in unlock.
  • Lock: Rear door lock-link switch (LH), rear door lock-link switch (RH) are in lock.
LLINK_SW_STAT_R Off/On
  • Off: Front door lock-link switch (driver's side) is in unlock.
  • On: Front door lock-link switch (driver's side) is in lock.
MASTER_KEY No/Yes
  • No: There is no master key.
  • Yes: There is master key.
MODE_ACTAT_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Airflow mode actuator is not equipped.
  • Node Attached and Communicate correctly: Airflow mode actuator is equipped, communication with airflow mode actuator is normal.
  • NodeAttached but Not Communicate correctly: Airflow mode actuator is equipped, but communication with airflow mode actuator is not normal.
MODE_PS_ACTAT_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
NOTE:
  • Displays in the M-MDS but it does not operate.
MTTR_TIMER hour If the ignition is switched off/main power is switched OFF after a specified time has elapsed or the vehicle has been driven for a specified period of time or more while in the fail-safe mode, the ignition will remain switched off/main power will remain switched OFF. Displays the elapsed time since the ignition could no longer be ON (engine on)/main power could no longer be ON (READY on).
NOX1_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: NOx sensor No. 1 is not equipped.
  • Node Attached and Communicate correctly: NOx sensor No. 1 is equipped, communication with NOx sensor No. 1 is normal.
  • NodeAttached but Not Communicate correctly: NOx sensor No. 1 is equipped, but communication with NOx sensor No. 1 is not normal.
NOX2_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: NOx sensor No. 2 is not equipped.
  • Node Attached and Communicate correctly: NOx sensor No. 2 is equipped, communication with NOx sensor No. 2 is normal.
  • NodeAttached but Not Communicate correctly: NOx sensor No. 2 is equipped, but communication with NOx sensor No. 2 is not normal.
OBC_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Battery charge control module is not equipped.
  • Node Attached and Communicate correctly: Battery charge control module is equipped, communication with battery charge control module is normal.
  • NodeAttached but Not Communicate correctly: Battery charge control module is equipped, but communication with battery charge control module is not normal.
OHC_ROOMLAMP_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Front map light is not equipped.
  • Node Attached and Communicate correctly: Front map light is equipped, communication with front map light is normal.
  • NodeAttached but Not Communicate correctly: Front map light is equipped, but communication with front map light is not normal.
OIL_LVL_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Engine oil level sensor is not equipped.
  • Node Attached and Communicate correctly: Engine oil level sensor is equipped, communication with engine oil level sensor is normal.
  • NodeAttached but Not Communicate correctly: Engine oil level sensor is equipped, but communication with engine oil level sensor is not normal.
OMC_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Driver monitoring camera unit is not equipped.
  • Node Attached and Communicate correctly: Driver monitoring camera unit is equipped, communication with driver monitoring camera unit is normal.
  • NodeAttached but Not Communicate correctly: Driver monitoring camera unit is equipped, but communication with driver monitoring camera unit is not normal.
OMM_LGHT_OFF Off/On
  • Off: Battery discharge suppression signal is not sent from body control module (BCM).
  • On: Battery discharge suppression signal is sent from body control module (BCM).
ONE_TOUCH_TURN Off/On
  • Off: Turn switch LH signal or the turn switch RH signal is not received.
  • On: Turn switch LH signal or the turn switch RH signal is received.
OUTLET_L1_REQ Off/On
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
OUTLET_R1_REQ Off/On
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
PARK_RANGE_SW Off/On
  • Off: NOT P position switch is off.
  • On: NOT P position switch is on.
PCM_PT_BUS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: PCM (except e-SKYACTIV PHEV) is not equipped.
  • Node Attached and Communicate correctly: PCM (except e-SKYACTIV PHEV) is equipped, communication via CAN BUS No. 2 with PCM (except e-SKYACTIV PHEV) is normal.
  • NodeAttached but Not Communicate correctly: PCM (except e-SKYACTIV PHEV) is equipped, but communication via CAN BUS No. 2 with PCM (except e-SKYACTIV PHEV) is not normal.
PCM_VEH_BUS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: PCM (except e-SKYACTIV PHEV) is not equipped.
  • Node Attached and Communicate correctly: PCM (except e-SKYACTIV PHEV) is equipped, communication via CAN BUS No. 1 with PCM (except e-SKYACTIV PHEV) is normal.
  • NodeAttached but Not Communicate correctly: PCM (except e-SKYACTIV PHEV) is equipped, but communication via CAN BUS No. 1 with PCM (except e-SKYACTIV PHEV) is not normal.
PLG_HZRD_REQ NoRequest/RequestControl
  • NoRequest: Hazard warning light flashing request signal is not received.
  • RequestControl: Hazard warning light flashing request signal is received.
PLG_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Power liftgate (PLG) control module is not equipped.
  • Node Attached and Communicate correctly: Power liftgate (PLG) control module is equipped, communication with power liftgate (PLG) control module is normal.
  • NodeAttached but Not Communicate correctly: Power liftgate (PLG) control module is equipped, but communication with power liftgate (PLG) control module is not normal.
PMS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Position memory control module is not equipped.
  • Node Attached and Communicate correctly: Position memory control module is equipped, communication with position memory control module is normal.
  • NodeAttached but Not Communicate correctly: Position memory control module is equipped, but communication with position memory control module is not normal.
PNC_ALRM_HZRD NoRequest/RequestControl
  • NoRequest: Hazard warning light flashing request signal is not received.
  • RequestControl: Hazard warning light flashing request signal is received.
PNC_ALRM_REQ NoRequest/RequestControl
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
POWER_MODE OFF/ACC/ON/CRANK
  • Displays ignition/main power status.
PSM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Parking assist unit (ultrasonic) is not equipped.
  • Node Attached and Communicate correctly: Parking assist unit (ultrasonic) is equipped, communication with parking assist unit (ultrasonic) is normal.
  • NodeAttached but Not Communicate correctly: Parking assist unit (ultrasonic) is equipped, but communication with parking assist unit (ultrasonic) is not normal.
PTC_HEAT_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: PTC heater is not equipped.
  • Node Attached and Communicate correctly: PTC heater is equipped, communication with PTC heater is normal.
  • NodeAttached but Not Communicate correctly: PTC heater is equipped, but communication with PTC heater is not normal.
R_FOG_SW_IN Off/On
  • Off: Rear fog light switch is off.
  • On: Rear fog light switch is on.
R_FOG_SW_OUT Inactive/Active
  • Inactive: Rear fog light is turned off.
  • Active: Rear fog light is turned on.
R_MIX_ACTAT_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
NOTE:
  • Displays in the M-MDS but it does not operate.
R_SEAT_REMINDER_FUNCTION NotAdopted (Not Change)/Off/Interior/Interior_and_Exterior
  • NotAdopted (Not Change): Rear seat belt reminder system is not equipped.
  • Off: Rear seat belt reminder system is off.
  • Interior: Personalization setting for rear seat belt reminder system is set to [In-vehicle Warning].
  • Interior_and_Exterior: Personalization setting for rear seat belt reminder system is set to [In-vehicle warning + Out-of-vehicle warning].
R_VENT_ACTAT_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Rear vent actuator is not equipped.
  • Node Attached and Communicate correctly: Rear vent actuator is equipped, communication with rear vent actuator is normal.
  • NodeAttached but Not Communicate correctly: Rear vent actuator is equipped, but communication with rear vent actuator is not normal.
R_WASH_SW Off/On
  • Off: Rear wiper and washer switch is not in rear washer position.
  • On: Rear wiper and washer switch is in rear washer position.
R_WIP Off/RearWiperLo/Not defined/WiperINT
  • Off: Rear wiper and washer switch is in the OFF position.
  • RearWiperLo: Rear wiper and washer switch is in the ON position.
  • Not defined: Rear wiper and washer switch position is not determined.
  • WiperINT: Rear wiper and washer switch is in the INT position.
R_WIP_CTRL Deactivate/Activate/Fail (Circuit Short to Ground)/Fail (Circuit Open)/Fail (Circuit Short to Battery) Rear wiper operation condition input signal from electrical supply unit (ESU)
  • Deactivate: Rear wiper is not operated.
  • Activate: Rear wiper is operated.
  • Fail (Circuit Short to Ground): Short to ground circuit malfunction is received from rear wiper.
  • Fail (Circuit Open): Open circuit malfunction is received from rear wiper.
  • Fail (Circuit Short to Battery): Short to battery circuit malfunction is received from rear wiper.
R_WIP_POS Unknown/Parking_Position/Not _Parking_Position/AS_SW_Failure
  • Unknown: Rear wiper position is not determined.
  • Parking_Position: Rear wiper in park position.
  • Not_Parking_Position: Rear wiper in position other than park.
  • AS_SW_Failure: Autostop switch has a malfunction.
R_WIP_REQ Off/Rear Wiper Low On/Stop
  • Off: Body control module (BCM) does not operate rear wiper.
  • Rear Wiper Low On: Body control module (BCM) operates rear wiper.
  • Stop: Body control module (BCM) operates rear wiper to the park position.
R_WIP_STALL_STAT OK/Stall
  • OK: Rear wiper motor is normal.
  • Stall: Rear wiper motor is stalled.
RCM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: SAS control module is not equipped.
  • Node Attached and Communicate correctly: SAS control module is equipped, communication with SAS control module is normal.
  • NodeAttached but Not Communicate correctly: SAS control module is equipped, but communication with SAS control module is not normal.
REGEN_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: EV system/hybrid system is not equipped.
  • Node Attached and Communicate correctly: EV system/hybrid system is equipped, communication with EV system/hybrid system is normal.
  • NodeAttached but Not Communicate correctly: EV system/hybrid system is equipped, but communication with EV system/hybrid system is not normal.
RES Off/On
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
RES_HZRD_ANS NoRequest/RequestControl
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
RF_TMTR FALSE/TRUE
  • FALSE: Remote transmitter ID information is not programmed in LF control unit.
  • TRUE: Remote transmitter ID information is programmed in LF control unit.
RLS_AMB_TEMP °C, °F Displays rain sensor ambient temperature.
RLS_AUTO_LGHT_REQ TNSOff/Head_Off/TNSOn/Head Off/TNSOn/HeadOn Illumination request by receiving TNS or headlight illumination request signal.
  • TNSOff/Head_Off: Body control module (BCM) does not operate the TNS (parking lights) and headlight on.
  • TNSOn/HeadOff: Body control module (BCM) operates the TNS (parking lights) on.
  • TNSOn/HeadOn: Body control module (BCM) operates the TNS (parking lights) and headlight on.
RLS_CTRL OFF/TNS Only ON/Low and TNS/Unknown Illumination request by receiving auto light signal, TNS or headlight illumination request signal.
  • OFF: Body control module (BCM) does not operate the TNS (parking lights) and headlight on.
  • TNS Only ON: Body control module (BCM) operates the TNS (parking lights) on.
  • Low and TNS: Body control module (BCM) operates the TNS (parking lights) and headlight on.
  • Unknown: TNS (parking lights) condition is not detected.
RLS_FAIL Normal/Fault
  • Normal: Error signals is not received from the auto light sensor.
  • Fault: Error signals is received from the auto light sensor.
RLS_FAIL_STAT Faulty (Faulty)/Initialize/Not within specifications/Normal (sensing) Displays auto light sensor condition input signal
RLS_FWD_LGHT_SEN OK/NG
  • OK: Normal forward brightness can be detected.
  • NG: Normal forward brightness cannot be detected.
RLS_LGHT_SEN_FAIL Normal/Fault
  • Normal: Error signals is not received from the auto light sensor.
  • Fault: Error signals is received from the auto light sensor.
RLS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Humidity sensor/solar radiation sensor/auto light sensor/rain sensor is not equipped.
  • Node Attached and Communicate correctly: Humidity sensor/solar radiation sensor/auto light sensor/rain sensor is equipped, communication with humidity sensor/solar radiation sensor/auto light sensor/rain sensor is normal.
  • NodeAttached but Not Communicate correctly: Humidity sensor/solar radiation sensor/auto light sensor/rain sensor is equipped, but communication with humidity sensor/solar radiation sensor/auto light sensor/rain sensor is not normal.
RLS_RAIN_SEN_FAIL Off/On
  • Off: Error signals is not received from the rain sensor.
  • On: Error signals is received from the rain sensor.
RLS_STAT Off/TNS On requested/TNS/Headlight On requested
  • Off: TNS (parking lights) and headlight illumination request signal is not received.
  • TNS On requested: TNS (parking lights) illumination request signal is received.
  • TNS/Headlight On requested: TNS (parking lights) and headlight illumination request signal is received.
RLS_TEMP_SEN_FAIL Normal/Fault
  • Normal: Error signals is not received from the temperature sensor (built into humidity sensor).
  • Fault: Error signals is received from the temperature sensor (built into humidity sensor).
RLS_UP_LGHT_SEN OK/NG
  • OK: Normal upward brightness can be detected.
  • NG: Normal upward brightness cannot be detected.
RLS_VOLT_FAIL Normal/Fault
  • Normal: Power supply voltage of humidity sensor/solar radiation sensor/auto light sensor/rain sensor is normal.
  • Fault: Power supply voltage of humidity sensor/solar radiation sensor/auto light sensor/rain sensor is not normal.
RLS_WINDOW_TEMP °C, °F Displays windshield temperature.
RLS_WIP_REQ WiperOFF/WiperOff_duringAutoINT/Single Wipe/SpeedLow/SpeedHigh/Failure
  • WiperOFF: Wiper operation signal is not received from rain sensor.
  • WiperOff_duringAutoINT: Error signals is received from the rain sensor.
  • Single Wipe: Signal to operate wiper once is received from rain sensor.
  • SpeedLow: Signal to operate wiper at low speed is received from rain sensor.
  • SpeedHigh: Signal to operate wiper at high speed is received from rain sensor.
  • Failure: Communication with rain sensor is failed.
RSRL_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Rear side radar sensor (LH) is not equipped.
  • Node Attached and Communicate correctly: Rear side radar sensor (LH) is equipped, communication with rear side radar sensor (LH) is normal.
  • NodeAttached but Not Communicate correctly: Rear side radar sensor (LH) is equipped, but communication with rear side radar sensor (LH) is not normal.
RSRR_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Rear side radar sensor (RH) is not equipped.
  • Node Attached and Communicate correctly: Rear side radar sensor (RH) is equipped, communication with rear side radar sensor (RH) is normal.
  • NodeAttached but Not Communicate correctly: Rear side radar sensor (RH) is equipped, but communication with rear side radar sensor (RH) is not normal.
S_BELT_LED_OFF_C/R Off/On
  • Off: Rear seat belt (center)/second-row seat belt (center) warning light (red) is not illuminated.
  • On: Rear seat belt (center)/second-row seat belt (center) warning light (red) is illuminated.
S_BELT_LED_OFF_L/R Off/On
  • Off: Rear seat belt (LH)/second-row seat belt (LH) warning light (red) is not illuminated.
  • On: Rear seat belt (LH)/second-row seat belt (LH) warning light (red) is illuminated.
S_BELT_LED_OFF_R/R Off/On
  • Off: Rear seat belt (RH)/second-row seat belt (RH) warning light (red) is not illuminated.
  • On: Rear seat belt (RH)/second-row seat belt (RH) warning light (red) is illuminated.
S_BELT_LED_ON_C/R Off/On
  • Off: Rear seat belt (center)/second-row seat belt (center) warning light (green) is not illuminated.
  • On: Rear seat belt (center)/second-row seat belt (center) warning light (green) is illuminated.
S_BELT_LED_ON_L/R Off/On
  • Off: Rear seat belt (LH)/second-row seat belt (LH) warning light (green) is not illuminated.
  • On: Rear seat belt (LH)/second-row seat belt (LH) warning light (green) is illuminated.
S_BELT_LED_ON_R/R Off/On
  • Off: Rear seat belt (RH)/second-row seat belt (RH) warning light (green) is not illuminated.
  • On: Rear seat belt (RH)/second-row seat belt (RH) warning light (green) is illuminated.
S_BELT_LED_P Off/On
  • Off: Passenger seat belt warning light is not illuminated.
  • On: Passenger seat belt warning light is illuminated.
S_BELT_STAT Vaild/Unknown
  • Vaild: All rear seat belt warning light signals are normal.
  • Unknown: There is a rear seat belt warning light signal error.
S_BELT_STAT_C/3RD 3rdCenter belt not used (Close)/3rdCenter belt used (Open)
  • RearCenter belt not used (Close): Third-row center seat belt is not fastened.
  • RearCenter belt used (Open): Third-row center seat belt is fastened.
S_BELT_STAT_C/R RearCenter belt not used (Close)/RearCenter belt used (Open)
  • RearCenter belt not used (Close): Rear center seat belt/second-row center seat belt is not fastened.
  • RearCenter belt used (Open): Rear center seat belt/second-row center seat belt is fastened.
S_BELT_STAT_L/3 RD 3rdLeft belt not used (Close)/3rdLeft belt used (Open)
  • RearCenter belt not used (Close): Third-row left seat belt is not fastened.
  • RearCenter belt used (Open): Third-row left seat belt is fastened.
S_BELT_STAT_L/R RL belt not used (Close)/RL belt used (Open)
  • RL belt not used (Close): Rear left seat belt/second-row left seat belt is not fastened.
  • RL belt used (Open): Rear left seat belt/second-row left seat belt is fastened.
S_BELT_STAT_R/3RD 3rdRight belt not used (Close)/3rdRight belt used (Open)
  • RearCenter belt not used (Close): Third-row right seat belt is not fastened.
  • RearCenter belt used (Open): Third-row right seat belt is fastened.
S_BELT_STAT_R/R RR belt not used (Close)/RR belt not used (Close)
  • RR belt not used (Close): Rear right seat belt/second-row right seat belt is not fastened.
  • RR belt used (Open): Rear right seat belt/second-row right seat belt is fastened.
S_BELT_WRNG_D driver belt not used/driver belt used/fault (hole IC switch)/resrve (mech switch)
  • driver belt not used: Driver seat belt is not fastened.
  • driver belt used: Driver seat belt is fastened.
  • fault (hole IC switch)/resrve (mech switch): Driver seat belt has a malfunction.
S_BELT_WRNG_P driver belt not used/driver belt used/fault (hole IC switch)/resrve (mech switch)
  • driver belt not used: Passenger seat belt is not fastened.
  • driver belt used: Passenger seat belt is fastened.
  • fault (hole IC switch)/resrve (mech switch): Passenger seat belt has a malfunction.
SAS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Steering angle sensor is not equipped.
  • Node Attached and Communicate correctly: Steering angle sensor is equipped, communication with steering angle sensor is normal.
  • NodeAttached but Not Communicate correctly: Steering angle sensor is equipped, but communication with steering angle sensor is not normal.
SCR_HZRD_REQ Off/On
  • Off: Secondary collision reduction hazard warning light is not operated.
  • On: Secondary collision reduction hazard warning light is operated.
SEAT_LETER_ILLMI Off/On
  • Off: Passenger air bag deactivation (PAD) lettering illumination is not illuminated.
  • On: Passenger air bag deactivation (PAD) lettering illumination is illuminated.
SEAT_OCS_C/R Unknown/Vacancy/Occupied/Malfunction
  • Unknown: Occupant sensor cannot be detected.
  • Vacancy: No occupant sitting in rear seat (center) is detected.
  • Occupied: Occupant sitting in rear seat (center) is detected.
  • Malfunction: Occupant sensor is malfunctioning.
SEAT_OCS_L/R Unknown/Vacancy/Occupied/Malfunction
  • Unknown: Occupant sensor cannot be detected.
  • Vacancy: No occupant sitting in rear seat (LH) is detected.
  • Occupied: Occupant sitting in rear seat (LH) is detected.
  • Malfunction: Occupant sensor is malfunctioning.
SEAT_OCS_R/R Unknown/Vacancy/Occupied/Malfunction
  • Unknown: Occupant sensor cannot be detected.
  • Vacancy: No occupant sitting in rear seat (RH) is detected.
  • Occupied: Occupant sitting in rear seat (RH) is detected.
  • Malfunction: Occupant sensor is malfunctioning.
SEAT_OCS_STAT Unknown/Vacancy/Occupied/Malfunction
  • Unknown: Occupant sensor cannot be detected.
  • Vacancy: No occupant sitting in front passenger seat is detected.
  • Occupied: Occupant sitting in front passenger seat is detected.
  • Malfunction: Occupant sensor is malfunctioning.
SHIFT between 2 positions/P/R/N/D/S (2)/L (1)/not used
  • between 2 positions: Selector lever is between two positions.
  • P: Selector lever is in P position.
  • R: Selector lever is in R position.
  • N: Selector lever is in N position.
  • D: Selector lever is in D position.
  • S (2): Selector lever is in D position 2nd gear.
  • L (1): Selector lever is in D position 1st gear.
  • not used: Selector lever is not used.
SLAM_LCK Off/On
  • Off: With all of the following conditions met, lock knob on door equipped with door lock-link switch is locked and all doors are closed.
    • Ignition is switched off/main power is switched OFF
    • Any door is open
  • On: Conditions other than above
SPARE_KEY_STAT Off/On
  • Off: There is no spare key.
  • On: There is spare key.
SSB_1 Off/On
  • Off: Push button start/power switch switch 1 is off.
  • On: Push button start/power switch switch 1 is on.
SSB_2 Off/On
  • Off: Push button start/power switch switch switch 2 is off.
  • On: Push button start/power switch switch switch 2 is on.
SSB_AMBER_REQ Off/On
  • Off: Push button start indicator light (amber)/power switch indicator light (amber) is turned off.
  • On: Push button start indicator light (amber)/power switch indicator light (amber) is illuminated.
SSB_GREEN_REQ Off/On
  • Off: Push button start indicator light (green)/power switch indicator light (green) is turned off.
  • On: Push button start indicator light (green)/power switch indicator light (green) is illuminated.
SSB_ILLMI_REQ Off/On
  • Off: START/STOP/ENGINE indicator light/POWER indicator light is turned off.
  • On: START/STOP/ENGINE indicator light/POWER indicator light is illuminated.
SSU_RES_NUM 0/1/2/3
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
SSU_RES_STAT Disable/Enable
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
STR_ANG ° (deg) Displays steering angle signal (absolute angle)
  • Steering wheel in neutral position: Near 0 degrees
  • Steering wheel turned to left: Changes from 0 degrees to positive
  • Steering wheel turned to right: Changes from 0 degrees to negative
STR_COLM_LCK_CTRL Off/On
  • Off: Steering lock is not operated.
  • On: Steering lock is operated.
STR_COLM_LCK_GND Off/On
  • Off: Shift-lock is operated.
  • On: Shift-lock is released.
STR_COLM_LCK_POWER Off/On
  • Off: Power is not supplied to steering lock.
  • On: Power is supplied to steering lock.
STR_COLM_LCK_STAT Locked/Failed 1/Failed 2/Unlocked/Undefined
  • Locked: Steering is locked.
  • Failed 1: Steering lock/unlock is failed.
  • Failed 2: Steering lock/unlock is failed.
  • Unlocked: Steering is not locked.
  • Undefined: Steering lock condition is not determined.
STR_HEAT_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Heated steering wheel control unit is not equipped.
  • Node Attached and Communicate correctly: Heated steering wheel control unit is equipped, communication with heated steering wheel control unit is normal.
  • NodeAttached but Not Communicate correctly: Heated steering wheel control unit is equipped, but communication with heated steering wheel control unit is not normal.
SUPER_LCK_ALL Off/On
  • Off: Double locking function is not operated.
  • On: Double locking function is operated.
T/LGT_LCK_SW Off/On
  • Off: Door lock switch (liftgate)/power liftgate (PLG) rear switch is off.
  • On: Door lock switch (liftgate)/power liftgate (PLG) rear switch is on.
T/LGT_SW Close/Open
  • Close: Trunk lid/liftgate is closed.
  • Open: Trunk lid/liftgate is open.
T/LGT_ULCK Off/On
  • Off: Body control module (BCM) does not operate the trunk lid/liftgate to unlock.
  • On: Body control module (BCM) operates the trunk lid/liftgate to unlock.
TCM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: TCM/selector lever is not equipped.
  • Node Attached and Communicate correctly: TCM/selector lever is equipped, communication with TCM/selector lever is normal.
  • NodeAttached but Not Communicate correctly: TCM/selector lever is equipped, but communication with TCM/selector lever is not normal.
TCM_PT2_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: TCM/selector lever is not equipped.
  • Node Attached and Communicate correctly: TCM/selector lever is equipped, communication via CAN BUS No. 2 with TCM/selector lever is normal.
  • NodeAttached but Not Communicate correctly: TCM/selector lever is equipped, but communication via CAN BUS No. 2 with TCM/selector lever is not normal.
TCU_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Emergency call unit/telematics communication unit is not equipped.
  • Node Attached and Communicate correctly: Emergency call unit/telematics communication unit is equipped, communication with emergency call unit/telematics communication unit is normal.
  • NodeAttached but Not Communicate correctly: Emergency call unit/telematics communication unit is equipped, but communication with emergency call unit/telematics communication unit is not normal.
TEMP_LH_ACTAT_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Driver-side air mix actuator is not equipped.
  • Node Attached and Communicate correctly: Driver-side air mix actuator is equipped, communication with driver-side air mix actuator is normal.
  • NodeAttached but Not Communicate correctly: Driver-side air mix actuator is equipped, but communication with driver-side air mix actuator is not normal.
TEMP_RH_ACTAT_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Passenger-side air mix actuator is not equipped.
  • Node Attached and Communicate correctly: Passenger-side air mix actuator is equipped, communication with passenger-side air mix actuator is normal.
  • NodeAttached but Not Communicate correctly: Passenger-side air mix actuator is equipped, but communication with passenger-side air mix actuator is not normal.
TGT_VERIFY Error/OK Displays immobilizer system condition.
TIRE_PRES_L/F kPa Displays tire pressure (wheel unit (LF))
TIRE_PRES_L/R kPa Displays tire pressure (wheel unit (LR))
TIRE_PRES_R/F kPa Displays tire pressure (wheel unit (RF))
TIRE_PRES_R/R kPa Displays tire pressure (wheel unit (RR))
TIRE_TEMP_L/F °C, °F Displays tire temperature (wheel unit (LF))
TIRE_TEMP_L/R °C, °F Displays tire temperature (wheel unit (LR))
TIRE_TEMP_R/F °C, °F Displays tire temperature (wheel unit (RF))
TIRE_TEMP_R/R °C, °F Displays tire temperature (wheel unit (RR))
TMTR_NUM 0/1/2/3/4/5/6 Displays registration number of the remote transmitter
TNS_REQ Off/On
  • Off: Body control module (BCM) does not operate the TNS (parking lights) on.
  • On: Body control module (BCM) operates the TNS (parking lights) on.
TNS_SW Off/On
  • Off: Light switch TNS (parking lights) signal is not received.
  • On: Light switch TNS (parking lights) signal is received.
TOPOLOGY_ID - Displays topological ID
TOTAL_DIST km, ft, mi Displays total traveled distance
TPMS_FAIL Default/Zero Learnt/One Learnt/Two Learnt/Three Learnt/ABS Error/Maximum speed exceeded/Location not determined/Locate data issue Displays reason why tire position recognition failed.
TPMS_MODE_L/F Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode Displays wheel unit (LF) mode
TPMS_MODE_L/R Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode Displays wheel unit (LR) mode
TPMS_MODE_R/F Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode Displays wheel unit (RF) mode
TPMS_MODE_R/R Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode Displays wheel unit (RR) mode
TUNER_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Remote tuner (RT) is not equipped.
  • Node Attached and Communicate correctly: Remote tuner (RT) is equipped, communication with remote tuner (RT) is normal.
  • NodeAttached but Not Communicate correctly: Remote tuner (RT) is equipped, but communication with remote tuner (RT) is not normal.
TURN_L Off/On
  • Off: Turn switch LH signal is not sent from body control module (BCM).
  • On: Turn switch LH signal is sent from body control module (BCM).
TURN_L_INTERIOR Off/On
  • Off: Turn signal (LH) or hazard warning indicator signal is not sent from body control module (BCM).
  • On: Turn signal (LH) or hazard warning indicator signal is sent from body control module (BCM).
TURN_R Off/On
  • Off: Turn switch RH signal is not sent from body control module (BCM).
  • On: Turn switch RH signal is sent from body control module (BCM).
TURN_R_INTERIOR Off/On
  • Off: Turn signal (RH) or hazard warning indicator signal is not sent from body control module (BCM).
  • On: Turn signal (RH) or hazard warning indicator signal is sent from body control module (BCM).
TURN_SW Turn Off/Turn Right ON/Turn Left ON/Unknown
  • Turn Off: Turn switch is in OFF position.
  • Turn Right ON: Turn switch is in RH position.
  • Turn Left ON: Turn switch is in LH position.
  • Unknown: Turn switch position is not determined.
USBHUB_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Auxiliary jack/USB port/SD card slot hub is not equipped.
  • Node Attached and Communicate correctly: Auxiliary jack/USB port/SD card slot hub is equipped, communication with auxiliary jack/USB port/SD card slot hub is normal.
  • NodeAttached but Not Communicate correctly: Auxiliary jack/USB port/SD card slot hub is equipped, but communication with auxiliary jack/USB port/SD card slot hub is not normal.
VCM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Vehicle control module (VCM) is not equipped.
  • Node Attached and Communicate correctly: Vehicle control module (VCM) is equipped, communication with vehicle control module (VCM) is normal.
  • NodeAttached but Not Communicate correctly: Vehicle control module (VCM) is equipped, but communication with vehicle control module (VCM) is not normal.
VDT_HZRD_REQ NoRequest/RequestControl
  • NoRequest: Hazard warning light flashing request signal is not received.
  • RequestControl: Hazard warning light flashing request signal is received.
VDT_MODE Normal Mode/Manual Trigger Mode/i-ActivSense Analysis Mode/Reject Mode
  • Normal Mode: Vehicle is in normal mode.
  • Manual Trigger Mode: Vehicle is in driving data collecting mode.
  • i-ActivSense Analysis Mode: Vehicle is in i-ACTIVSENSE data collecting mode.
  • Reject Mode: Restricted remote operation and data transfer.
VMC_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: 360°view monitor control module/parking assist unit (optical) is not equipped.
  • Node Attached and Communicate correctly: 360°view monitor control module/parking assist unit (optical) is equipped, communication with 360°view monitor control module/parking assist unit (optical) is normal.
  • NodeAttached but Not Communicate correctly: 360°view monitor control module/parking assist unit (optical) is equipped, but communication with 360°view monitor control module/parking assist unit (optical) is not normal.
VPWR_CBCM V Displays power supply voltage of body control module (BCM)
VPWR_ESCL Volt Displays voltage at body control module (BCM) power supply terminal
(BATT3_ESCL) VPWR_IG Volt Displays voltage at body control module (BCM) terminal
(IG1_MONITOR) VPWR_LIMP_HOM E Volt Displays voltage at body control module (BCM) power supply terminal
(BATT1_LIMPHOME) VPWR_ROOM Volt Displays voltage at body control module (BCM) power supply terminal
(BATT2_ROOM) WASH_MOTOR_STAT Off/Washer_Motor_L/Washer_Motor_R
  • Off: Windshield washer motor relay and rear washer motor relay are off.
  • Washer_Motor_L: Windshield washer motor relay is on.
  • Washer_Motor_R: Rear washer motor relay is on.
WC_Qi_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Wireless charger (Qi) is not equipped.
  • Node Attached and Communicate correctly: Wireless charger (Qi) is equipped, communication with wireless charger (Qi) is normal.
  • NodeAttached but Not Communicate correctly: Wireless charger (Qi) is equipped, but communication with wireless charger (Qi) is not normal.
WIP_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Windshield wiper motor is not equipped.
  • Node Attached and Communicate correctly: Windshield wiper motor is equipped, communication with windshield wiper motor is normal.
  • NodeAttached but Not Communicate correctly: Windshield wiper motor is equipped, but communication with windshield wiper motor is not normal.
scientia non olet · About LEMON Manuals