Engine Control System (VIN A) (2 Of 2)
- Fuel Vapor Temperature Sensor Removal/Installation [PYUL]
- D-code
- Perform Precaution Before Service
- Perform Fuel Siphoning Procedure
- Open Capsule Cover
- Perform Fuel Siphoning
- High Voltage Part Inspection And Removal/Installation Notes
- Remove Cover Assembly (Passenger's Side)
- Disconnect Negative Lead-Acid Battery Terminal
- Remove Second-Row Seat (6:4 Split Adjustable Type Bench Seat Type)
- Remove Second-Row Seat (Captain Seat Type)
- Remove Service Hole Cover
- Disconnect Quick Release Connector (Fuel System) No. 4
- Remove Set Plate
- Disconnect Quick Connector (Fuel System) No. 7
- Remove Fuel Pump Unit Component
- Remove 150 W Power Supply Unit
- Remove Service Hole Cover (High Voltage Battery)
- Remove Service Plug
- Remove Front Under Cover No. 3
- Remove Floor Under Cover (Left side)
- Remove Rear Under Cover No. 1 (Left Side)
- Remove Terminal Cover (High Voltage Battery Side)
- Perform High Voltage Handling
- Recover Refrigerant
- Remove Floor Under Cover (Right side)
- Remove Rear Under Cover No. 1 (Right Side)
- Remove Tunnel Member
- Remove Middle Pipe
- Remove Insulator (Front No. 1)
- Remove Insulator (Front No. 2)
- Remove Insulator (Front No. 3)
- Remove Insulator (Middle No. 1)
- Remove Insulator (Middle No. 2)
- Remove Insulator Bracket No. 1
- Remove Insulator Bracket No. 2
- Remove Rear Propeller Shaft
- Remove Harness Bracket (High Voltage Battery)
- Disconnect DC-DC Converter (e-SKYACTIV PHEV)
- Disconnect Water Heater Component
- Disconnect Water Pipe
- Disconnect Battery Control Connector (Rear Side)
- Disconnect High Voltage Cable (High Voltage Battery Side)
- Disconnect High Voltage Cable (Inverter Side)
- Remove High Voltage Cable
- Remove High Voltage Battery
- Disconnect Quick Release Connector (Fuel System) No. 5
- Disconnect Quick Release Connector (Emission System) No. 6
- Remove Joint Hose
- Remove Fuel Tank Insulator
- Remove Fuel Tank Strap (LH)
- Remove Fuel Tank Strap (RH)
- Remove Fuel Tank
- Install in Reverse Order of Removal
- Perform Precaution After Service
- Charge Refrigerant
- Connect Manifold Gauge
- Inspect Refrigerant System Performance
- Perform Power Liftgate Initialization
- Initialize Power Outer Mirror Retract/Return Function
- Heated Oxygen Sensor (Ho2S) Inspection [PYUL]
- Heated Oxygen Sensor (Ho2S) Removal/Installation [PYUL]
- Intake Air Temperature (IAT) Sensor Inspection [PYUL]
- Knock Sensor (KS) Inspection [PYUL]
- Knock Sensor (KS) Removal/Installation [PYUL]
- D-code
- Remove Capsule Cover
- Remove Cover Assembly (Passenger's Side)
- Disconnect Negative Lead-Acid Battery Terminal
- High Voltage Part Inspection And Removal/Installation Notes
- Remove 150 W Power Supply Unit
- Remove Service Hole Cover (High Voltage Battery)
- Remove Service Plug
- Remove Front Under Cover No. 3
- Remove Floor Under Cover (Left side)
- Remove Rear Under Cover No. 1 (Left Side)
- Remove Terminal Cover (High Voltage Battery Side)
- Perform High Voltage Handling
- Remove Cover Assembly (Driver's Side)
- Remove Driver's Side Wiper Arm Cover
- Remove Passenger's Side Wiper Arm Cover
- Remove Driver's Side Windshield Wiper Arm And Blade
- Remove Passenger's Side Windshield Wiper Arm And Blade
- Remove Driver's Side Front Fender Molding
- Remove Passenger's Side Front Fender Molding
- Remove Cowl Grille
- Remove Side Cowl Grille (Passenger's Side)
- Remove Side Cowl Grille (Driver's Side)
- Remove Windshield Wiper Motor And Link
- Remove Driver Side Strut Tower Bar
- Remove Passenger Side Strut Tower Bar
- Remove Engine Compartment Insulator (Upper)
- Remove Air Cleaner Component
- Remove ECM Component
- Remove A/C Compressor Bracket (with USA/Canada spec)
- Remove Intake Manifold
- Remove Knock Sensor
- Install in Reverse Order of Removal
- Perform Precaution After Service
- Perform Power Liftgate Initialization
- Initialize Power Outer Mirror Retract/Return Function
- Power outer mirrors are in returned position
- Perform Windshield Wiper Arm And Blade Initial Setting
- Manifold Absolute Pressure (Map) Sensor Inspection [PYUL]
- MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR/INTAKE AIR TEMPERATURE (IAT) SENSOR No. 2 REMOVAL/INSTALLATION [PYUL]
- D-code
- Remove Capsule Cover
- Remove Cover Assembly (Passenger's Side)
- Disconnect Negative Lead-Acid Battery Terminal
- Remove Driver's Side Wiper Arm Cover
- Remove Passenger's Side Wiper Arm Cover
- Remove Driver's Side Windshield Wiper Arm And Blade
- Remove Passenger's Side Windshield Wiper Arm And Blade
- Remove Cover Assembly (Driver's Side)
- Remove Driver's Side Front Fender Molding
- Remove Passenger's Side Front Fender Molding
- Remove Cowl Grille
- Remove Side Cowl Grille (Driver's Side)
- Remove Side Cowl Grille (Passenger's Side)
- Remove Windshield Wiper Motor And Link
- Remove Driver Side Strut Tower Bar
- Remove Passenger Side Strut Tower Bar
- Remove Engine Compartment Insulator (Upper)
- Remove MAP sensor/IAT sensor No. 2
- Install in Reverse Order of Removal
- Perform Windshield Wiper Arm And Blade Initial Setting
- Perform Power Liftgate Initialization
- Initialize Power Outer Mirror Retract/Return Function
- Power outer mirrors are in returned position
- Mass Air Flow (MAF) Sensor Inspection [PYUL]
- MASS AIR FLOW (MAF) SENSOR/INTAKE AIR TEMPERATURE (IAT) SENSOR No. 1 REMOVAL/INSTALLATION [PYUL]
- Pcm Inspection [PYUL]
- Pcm Removal/Installation [001]
- D-code
- Perform Viewing Information Verification
- Perform PCM Read
- Remove Cover Assembly (Passenger's Side)
- Disconnect Negative Lead-Acid Battery Terminal
- Remove Passenger Side Front Seat
- Remove Passenger Side Front Scuff Plate
- Remove Front Side Trim (Right Side)
- Remove The Backup Power Supply Unit
- Remove PCM
- Install in Reverse Order of Removal
- Perform PCM Write
- Perform Immobilizer System-Related Part Programming
- Inspect for DTCs
- Clear DTCs
- Perform Power Liftgate Initialization
- Initialize Power Outer Mirror Retract/Return Function
- Pcm Removal/Installation [002]
- D-code
- Perform Viewing Information Verification
- Remove Cover Assembly (Passenger's Side)
- Disconnect Negative Lead-Acid Battery Terminal
- Remove Passenger Side Front Seat
- Remove Passenger Side Front Scuff Plate
- Remove Front Side Trim (Right Side)
- Remove The Backup Power Supply Unit
- Remove PCM
- Install in Reverse Order of Removal
- Perform Power Liftgate Initialization
- Initialize Power Outer Mirror Retract/Return Function
- Pcm Removal/Installation [PYUL]
- Throttle Position (TP) Sensor Inspection [PYUL]
- Throttle Position (TP) Sensor Removal/Installation [PYUL]
- i-stop OFF SWITCH INSPECTION [PYUL]
- i-stop OFF SWITCH REMOVAL/INSTALLATION [PYUL]
- D-code
- Remove Cover Assembly (Passenger's Side)
- Disconnect Negative Lead-Acid Battery Terminal
- Remove Driver Side Front Scuff Plate
- Remove Front Side Trim (Left Side)
- Remove Driver Side Decoration Panel
- Remove Passenger Side Decoration Panel
- Remove Driver Side Lower Panel
- Remove Cluster Switch No. 1
- Install in Reverse Order of Removal
- Perform Power Liftgate Initialization
- Initialize Power Outer Mirror Retract/Return Function