LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2023 >> CX-5 S Select >> Repair and Diagnosis >> External Pages >> Different car >> Section 144 (Air Bag System (Service Information) - Two-Step Deployment Control System) >> Driver-Side Air Bag Module Removal [Two-Step Deployment Control System - Us/CANADA Spec.] >> With Steering Warmer System

With Steering Warmer System

WARNING: This page is about a different car, the 2017 Mazda CX-5. However, it is still accessible from the selected car via links, so may be relevant.
  1. Switch the ignition off.
  2. Disconnect the negative battery terminal and wait for 1 min or more. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION .)
  3. Lower the steering wheel to the bottommost position.
  4. Pull the steering wheel to furthest position rearward.
  5. Rotate the steering wheel until the service hole can be seen from behind the steering wheel.
    Fig 1: Rotating Steering Wheel Until Service Hole Can Be Seen From Behind Steering Wheel
    G11428440Courtesy of MAZDA MOTORS CORP.
  6. Insert the tool in to the service hole.
    Fig 2: Inserting Tool Into Service Hole
    G11428441Courtesy of MAZDA MOTORS CORP.

    Recommended tool 

    • TORX driver (T30 (diam. 6))
  7. Move the tool in the direction of the arrow shown in the figure and disengage driver-side air bag module tab A from steering wheel hook A.
    Fig 3: Detaching Driver-Side Air Bag Module Tab From Steering Wheel Hook
    G11428442Courtesy of MAZDA MOTORS CORP.
  8. Rotate the steering wheel until the service hole can be seen from behind the steering wheel.
    Fig 4: Rotating Steering Wheel Until Service Hole Can Be Seen From Behind Steering Wheel
    G11428443Courtesy of MAZDA MOTORS CORP.
  9. Insert the tool in to the service hole.
    Fig 5: Inserting Tool Into Service Hole
    G11428444Courtesy of MAZDA MOTORS CORP.
  10. Move the tool in the direction of the arrow shown in the figure and disengage driver-side air bag module tab B from steering wheel hook B.
    NOTE:
    • By moving the tool, the omega spring is pressed at the same time allowing the omega spring to be removed from steering wheel hook D.
    Fig 6: Detaching Driver-Side Air Bag Module Tab From Steering Wheel Hook
    G11428445Courtesy of MAZDA MOTORS CORP.
  11. Rotate the steering wheel until the service hole can be seen from behind the steering wheel.
    Fig 7: Rotating Steering Wheel Until Service Hole Can Be Seen From Behind Steering Wheel
    G11428446Courtesy of MAZDA MOTORS CORP.
  12. Insert the tool in to the service hole.
    Fig 8: Inserting Tool Into Service Hole
    G11428447Courtesy of MAZDA MOTORS CORP.
    CAUTION:
    • The driver-side air bag module could be damaged if it is dropped while it is completely disengaged from the steering wheel. Hold the driver-side air bag module securely with a hand while it is completely disengaged.
  13. Move the tool in the direction of the arrow shown in the figure and disengage driver-side air bag module tab C from steering wheel hook C.
    NOTE:
    • By moving the tool, the omega spring is pressed at the same time allowing the omega spring to be removed from steering wheel hook E.
    Fig 9: Detaching Driver-Side Air Bag Module Tab From Steering Wheel Hook
    G11428448Courtesy of MAZDA MOTORS CORP.
  14. Remove the air bag module from the steering wheel.
  15. Using a flathead screwdriver, lift the locking device carefully, however do not remove it.
    Fig 10: Lifting Locking Device Carefully Using Flathead Screwdriver
    G11428449Courtesy of MAZDA MOTORS CORP.
  16. Disconnect the air bag module connectors.
  17. Disconnect the horn switch connector.
  18. Remove the driver-side air bag module.
scientia non olet · About LEMON Manuals