Diagnostic Procedure

DTC P0850:00 (PCM, SKYACTIV-G, US) DIAGNOSTIC PROCEDURE

Step	Inspection	Results	Action
1	RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION Record the freeze frame data/snapshot data. NOTE: Recording can be facilitated using the screen capture function of the PC.	-	Go to the next step.
2	VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY Verify related Service Bulletins, on-line repair information, or Service Information availability. Is any related Information available?	Yes	Perform repair or diagnosis according to the available information. If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	INSPECT NEUTRAL SENSOR CONNECTOR FOR MALFUNCTION Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION .) Are the connector and terminal normal?	Yes	Go to the next step.
3		No	Repair or replace the malfunctioning location and perform the repair completion verification.
4	INSPECT PCM CONNECTOR FOR MALFUNCTION Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION .) Are the connector and terminal normal?	Yes	Go to the next step.
4		No	Repair or replace the malfunctioning location and perform the repair completion verification.
5	INSPECT NEUTRAL SENSOR POWER SUPPLY CIRCUIT AND SIGNAL CIRCUIT FOR SHORT TO GROUND Inspect the applicable circuit for a short to ground. (See CIRCUIT INSPECTION .) Is the circuit normal?	Yes	Go to the next step.
5		No	Repair or replace the malfunctioning location and perform the repair completion verification.
6	INSPECT NEUTRAL SENSOR SIGNAL CIRCUIT AND GROUND CIRCUIT FOR SHORT TO POWER SUPPLY Inspect the applicable circuit for a short to power supply. (See CIRCUIT INSPECTION .) Is the circuit normal?	Yes	Go to the next step.
6		No	Repair or replace the malfunctioning location and perform the repair completion verification.
7	INSPECT NEUTRAL SENSOR POWER SUPPLY CIRCUITS, SIGNAL CIRCUITS, AND GROUND CIRCUITS FOR OPEN CIRCUIT Inspect the applicable circuit for open circuit. (See CIRCUIT INSPECTION .) Is the circuit normal?	Yes	Go to the next step.
7		No	Repair or replace the malfunctioning location and perform the repair completion verification.
8	INSPECT NEUTRAL SENSOR FOR MALFUNCTION Inspect the applicable part. (See NEUTRAL SENSOR INSPECTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))] .) Is the part normal?	Yes	Go to the next step.
8		No	Repair or replace the malfunctioning location and perform the repair completion verification. (See NEUTRAL SENSOR REMOVAL/INSTALLATION [C66M-R] .)
Repair completion verification 1	VERIFY THAT VEHICLE IS REPAIRED Install/connect the part removed/disconnected during the troubleshooting procedure. Clear the DTC recorded in the memory. (See CLEARING DTC .) Replicate the vehicle conditions at the time the DTC was detected using the following procedure. WARNING: While performing this step, always operate the vehicle in a safe and lawful manner. When the M-MDS is used to observe monitor system status while driving, be sure to have another technician with you, or record the data in the M-MDS using the PID/DATA MONITOR AND RECORD capturing function and inspect later. Drive the vehicle above 30 km/h {19 mph} and stop the vehicle. Depress and release the clutch pedal more than 10 times during drive cycle. Perform the DTC inspection for the PCM. (See DTC INSPECTION .) Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)] .) If the CAN communication is normal, perform the diagnosis from Step 1. If the malfunction recurs, replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))] .)
Repair completion verification 1		No	Go to the next step.
Repair completion verification 2	VERIFY IF OTHER DTCs DISPLAYED Perform the DTC inspection. (See DTC INSPECTION .) Are any other DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
Repair completion verification 2		No	DTC troubleshooting completed.