LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2021 >> CX-30 Turbo >> Repair and Diagnosis >> Accessories & Equipment >> Communication Devices >> On-Board Diagnostic - Body Control Module (BCM) (2 Of 2) >> PID/Data Monitor Table [Body Control Module (BCM) (Us)]

PID/Data Monitor Table [Body Control Module (BCM) (Us)]

-: Not applicable

PID/DATA MONITOR DESCRIPTION

PID Unit/Operation Data contents Module control terminal
7GTURN_APPLIED_STAT Off/On
  • Off: Turn light request signal is not received.
  • On: Turn light request signal is received.
 -
ACC_RLY Off/On
  • Off: ACC relay drive is off.
  • On: ACC relay drive is on.
 -
AGS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: TCM is not equipped.
  • Node Attached and Communicate correctly: TCM is equipped, communication with TCM is normal.
  • NodeAttached but Not Communicate correctly: TCM is equipped, but communication with TCM is not normal.
 -
AIR_INTAKE_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Air intake actuator is not equipped.
  • Node Attached and Communicate correctly: Air intake actuator is equipped, communication with air intake actuator is normal.
  • NodeAttached but Not Communicate correctly: Air intake actuator is equipped, but communication with air intake actuator is not normal.
 -
ALH_HBC_SW Off/On
  • Off: Adaptive LED headlight/High Beam Control System (HBC) switch is off.
  • On: Adaptive LED headlight/High Beam Control System (HBC) switch is on.
 -
ALH_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Adaptive front lighting system (AFS) control module is not equipped.
  • Node Attached and Communicate correctly: Adaptive front lighting system (AFS) control module is equipped, communication with adaptive front lighting system (AFS) control module is normal.
  • NodeAttached but Not Communicate correctly: Adaptive front lighting system (AFS) control module is equipped, but communication with Adaptive front lighting system (AFS) control module is not normal.
 -
AMB_TEMP °C, °F Displays ambient temperature -
AMP_CAN_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Audio amplifier is not equipped.
  • Node Attached and Communicate correctly: Audio amplifier is equipped, CAN communication with audio amplifier is normal.
  • NodeAttached but Not Communicate correctly: Audio amplifier is equipped, but CAN communication with audio amplifier is not normal.
 -
AMP_MOST_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Audio amplifier is not equipped.
  • Node Attached and Communicate correctly: Audio amplifier is equipped, MOST communication with audio amplifier is normal.
  • NodeAttached but Not Communicate correctly: Audio amplifier is equipped, but MOST communication with audio amplifier is not normal.
 -
ANTI_THEFT_SYS OFF/ON
  • OFF: Advanced keyless function is off.
  • ON: Advanced keyless function is on.
 -
APP % Accelerator pedal opening angle (relative value) with the fully released status as 0% and fully depressed status as 100% -
AT_IND_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Shift position indication is not equipped.
  • Node Attached and Communicate correctly: Shift position indication is equipped, communication with shift position indication is normal.
  • NodeAttached but Not Communicate correctly: Shift position indication is equipped, but communication with shift position indication is not normal.
 -
AUTO_LGHT_OFF Off/On
  • Off: TNS (parking lights) or headlight off control by auto light off system is not operated.
  • On: TNS (parking lights) or headlight off control by auto light off system is operated.
 -
BATT_SEN_NET WORK
NOTE:
  • Displays in the M-MDS but it does not operate.
BATT_SOC % Battery charge condition (estimated) -
BBS_NETWORK
NOTE:
  • Displays in the M-MDS but it does not operate.
BECM_NETWOR K
NOTE:
  • Displays in the M-MDS but it does not operate.
BGLR_ALRM NoRequest/RequestControl
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
 -
BGLR_ALRM_ANS NoRequest/RequestControl
  • NoRequest: Hazard warning light flashing answer-back signal is not received.
  • RequestControl: Hazard warning light flashing answer-back signal is received.
 -
BGLR_ALRM_REQ NoRequest/Request
  • NoRequest: Body control module (BCM) does not operate theft-deterrent horn and hazard warning lights on.
  • RequestControl: Body control module (BCM) operates the theft-deterrent horn and hazard warning lights on.
 -
BGLR_BACKUP_SIREN Off/On
  • Off: Backup siren setting is not turned on.
  • On: Backup siren setting is turned on.
 3O
BGLR_CHARGE
NOTE:
  • Displays in the M-MDS but it does not operate.
BGLR_GAIN
NOTE:
  • Displays in the M-MDS but it does not operate.
BGLR_HZRD_REQ Off/Blink 1 time/Blink 2 times/Blink 3 times
  • Off: Hazard warning lights are not operated to flash.
  • Blink 1 time: Hazard warning lights are operated to flash once.
  • Blink 2 times: Hazard warning lights are operated to flash twice.
  • Blink 3 times: Hazard warning lights are operated to flash three times.
 -
BGLR_IMS
NOTE:
  • Displays in the M-MDS but it does not operate.
BGLR_IS_COMD
NOTE:
  • Displays in the M-MDS but it does not operate.
BGLR_SEN Off/On
  • Off: Intruder sensor setting is not turned on.
  • On: Intruder sensor setting is turned on.
 3O
BGLR_SIREN_COMD
NOTE:
  • Displays in the M-MDS but it does not operate.
BGLR_SIREN_MODE
NOTE:
  • Displays in the M-MDS but it does not operate.
BGLR_STAT DEAD/INITIAL/PRE-ARMING/ARMING/ARMING STAND BY/ALARM/ALARM STAND BY
  • DEAD: Ignition is in ACC or ON (engine off) and alarm cannot be activated.
  • INITIAL: Ignition is switched OFF and transition to arming stand-by status is possible.
  • PRE-ARMING: Transition period to arming status.
  • ARMING: Alarm can be activated by inputting alarm trigger.
  • ARMING STAND BY: Liftgate is open under arming status.
  • ALARM: Alarm trigger is input and alarm is activated.
  • ALARM STAND BY: After alarm activation finished, standing by for next alarm trigger input.
 -
BGLR_SLEEP_M ODE
NOTE:
  • Displays in the M-MDS but it does not operate.
B-ISG_NETWORK
NOTE:
  • Displays in the M-MDS but it does not operate.
BRK_SW Not Stepping/Stepping
  • Not Stepping: Brake pedal is not depressed.
  • Stepping: Brake pedal is depressed.
 -
BRK_SW_1 Off/On
  • Off: Brake switch (No. 1 signal) is off.
  • On: Brake switch (No. 1 signal) is on.
 -
C_DOOR_LCK_SW_D Neutral/Lock/Unlock
  • Neutral: Door lock switch (driver's side) is neither locked nor unlocked.
  • Lock: Door lock switch (driver's side) is in lock.
  • Unlock: Door lock switch (driver's side) is in unlock.
 -
C_DOOR_LCK_SW_P Neutral/Lock/Unlock
  • Neutral: Door lock switch (passenger's side) is neither locked nor unlocked.
  • Lock: Door lock switch (passenger's side) is in lock.
  • Unlock: Door lock switch (passenger's side) is in unlock.
 -
CBCM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Body control module (BCM) is not equipped.
  • Node Attached and Communicate correctly: Body control module (BCM) is equipped, communication with body control module (BCM) is normal.
  • NodeAttached but Not Communicate correctly: Body control module (BCM) is equipped, but communication with body control module (BCM) is not normal.
 -
CENTER_DISP_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Center display is not equipped.
  • Node Attached and Communicate correctly: Center display is equipped, communication with center display is normal.
  • Node Attached but Not Communicate correctly: Center display is equipped, but communication with center display is not normal.
 -
CLTCH_INH_SW Off/On
  • Off: Starter interlock switch is off.
  • On: Starter interlock switch is on.
 -
CMU_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Connectivity master unit (CMU) is not equipped.
  • Node Attached and Communicate correctly: Connectivity master unit (CMU) is equipped, communication with connectivity master unit (CMU) is normal.
  • NodeAttached but Not Communicate correctly:Connectivity master unit (CMU) is equipped, but communication with connectivity master unit (CMU) is not normal.
 -
COMMANDER_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Commander switch is not equipped.
  • Node Attached and Communicate correctly: Commander switch is equipped, communication with commander switch is normal.
  • NodeAttached but Not Communicate correctly: Commander switch is equipped, but communication with commander switch is not normal.
 -
CRASH_SIG Off/On
  • Off: Crash signal is not received.
  • On: Crash signal is received.
 2J, 2L
Dash-ESU_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Dash-electrical supply unit is not equipped.
  • Node Attached and Communicate correctly: Dash-electrical supply unit is equipped, dash-electrical supply unit is normal.
  • NodeAttached but Not Communicate correctly: Dash-electrical supply unit is equipped, but communication with dash-electrical supply unit is not normal.
 -
DCDC_NETWOR K
NOTE:
  • Displays in the M-MDS but it does not operate.
DCDC_PCM_NETWORK
NOTE:
  • Displays in the M-MDS but it does not operate.
Door_ESU_D_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Door-electrical supply unit (driver's side) is not equipped.
  • Node Attached and Communicate correctly: Door-electrical supply unit (driver's side) is equipped, communication with door-electrical supply unit (driver's side) is normal.
  • NodeAttached but Not Communicate correctly: Door-electrical supply unit (driver's side) is equipped, but communication with door-electrical supply unit (driver's side) is not normal.
 -
Door_ESU_P_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Door-electrical supply unit (passenger's side) is not equipped.
  • Node Attached and Communicate correctly: Door-electrical supply unit (passenger's side) is equipped, communication with door-electrical supply unit (passenger's side) is normal.
  • NodeAttached but Not Communicate correctly: Door-electrical supply unit (passenger's side) is equipped, but communication with door-electrical supply unit (passenger's side) is not normal.
 -
DOOR_LCK_ALL Off/On
  • Off: All door lock signal is not sent from body control module (BCM).
  • On: All door lock signal is sent from body control module (BCM).
 2J, 2L
DOOR_LCK_ID_CREATE Off/On Displays door lock control ID creation status. -
DOOR_SECURITY Off/On Displays door lock control security condition. -
DOOR_SW_ALL Close/Open
  • Close: All doors are closed.
  • Open: Any door is open.
 -
DOOR_SW_D Close/Open
  • Close: Front door (driver's side) is closed.
  • Open: Front door (driver's side) is open.
 2J, 2L
DOOR_SW_L/R Close/Open
  • Close: Rear door (LH) is closed.
  • Open: Rear door (LH) is open.
 2J, 2L
DOOR_SW_P Close/Open
  • Close: Front door (passenger's side) is closed.
  • Open: Front door (passenger's side) is open.
 2J, 2L
DOOR_SW_R/R Close/Open
  • Close: Rear door (RH) is closed.
  • Open: Rear door (RH) is open.
 2J, 2L
DOOR_ULCK_ALL Off/On
  • Off: All door unlock signal is not sent from body control module (BCM).
  • On: All door unlock signal is sent from body control module (BCM).
 2J, 2L
DOOR_ULCK_D Off/On
  • Off: Front door (driver's side) unlock request signal is not sent from body control module (BCM).
  • On: Front door (driver's side) unlock request signal is sent from body control module (BCM).
 2J, 2L
DRL
NOTE:
  • Displays in the M-MDS but it does not operate.
DRL_REQ Off/On
  • Off: Body control module (BCM) does not operate daytime running light (DRL) on.
  • On: Body control module (FBCM) operates the daytime running light (DRL) on.
 -
DSC_PT_BUS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: DSC HU/CM is not equipped.
  • Node Attached and Communicate correctly: DSC HU/CM is equipped, communication via CAN BUS No. 2 with DSC HU/CM is normal.
  • NodeAttached but Not Communicate correctly: DSC HU/CM is equipped, but communication via CAN BUS No. 2 with DSC HU/CM is not normal.
 -
DSC_VEH_BUS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: DSC HU/CM is not equipped.
  • Node Attached and Communicate correctly: DSC HU/CM is equipped, communication via CAN BUS No. 1 with DSC HU/CM is normal.
  • NodeAttached but Not Communicate correctly: DSC HU/CM is equipped, but communication via CAN BUS No. 1 with DSC HU/CM is not normal.
 -
DSM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Seat warmer control unit is not equipped.
  • Node Attached and Communicate correctly: Seat warmer control unit is equipped, communication via CAN BUS No. 1 with seat warmer control unit is normal.
  • NodeAttached but Not Communicate correctly: Seat warmer control unit is equipped, but communication via CAN BUS No. 1 with seat warmer control unit is not normal.
 -
DVD_NETWORK
NOTE:
  • Displays in the M-MDS but it does not operate.
ENG_RPM_VSPD_RATIO Rpm/Kph Displays engine speed -
ENG_STARTER_VOLT_1 V Displays voltage at body control module (BCM) terminal 2T 2T
ENG_STARTER_VOLT_2 V Displays voltage at body control module (BCM) terminal 2AD 2AD
ENG_STAT Off/Ready/Cranking/Running/Stalled/Afterrun/Shutdown/Not defined Displays engine condition -
EPS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Electric Power Steering (EPS) control module is not equipped.
  • Node Attached and Communicate correctly: Electric Power Steering (EPS) control module is equipped, communication with Electric Power Steering (EPS) control module is normal.
  • NodeAttached but Not Communicate correctly: Electric Power Steering (EPS) control module is equipped, but communication with Electric Power Steering (EPS) control module is not normal.
 -
ESS_HZRD
NOTE:
  • Displays in the M-MDS but it does not operate.
ESU_CAN_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Electrical supply unit (ESU) is not equipped.
  • Node Attached and Communicate correctly: Electrical supply unit (ESU) is equipped, CAN communication with electrical supply unit (ESU) is normal.
  • NodeAttached but Not Communicate correctly: Electrical supply unit (ESU) is equipped, but CAN communication with electrical supply unit (ESU) is not normal.
 -
ESU_LIN_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Electrical supply unit (ESU) is not equipped.
  • Node Attached and Communicate correctly: Electrical supply unit (ESU) is equipped, LIN communication with electrical supply unit (ESU) is normal.
  • NodeAttached but Not Communicate correctly: Electrical supply unit (ESU) is equipped, but LIN communication with electrical supply unit (ESU) is not normal.
 -
EXT_T/LGT_REL_SW Off/On
  • Off: Liftgate opener switch is not pressed.
  • On: Liftgate opener switch is pressed.
 4J
F_WASH_CTRL_ALLW Wash_Allowed/Not_Allowed
  • Wash_Allowed: Use of windshield washer is permitted.
  • Not_Allowed: Use of windshield washer is not permitted.
 -
F_WASH_SW Off/On
  • Off: Windshield washer switch is off.
  • On: Windshield washer switch is on.
 -
F_WIP OFF/FrontWiper On Lo/FrontWiper On Hi/FrontWiperINT Auto On
  • OFF: Windshield wiper switch is in the OFF position.
  • FrontWiper On Lo: Windshield wiper switch is in the LO position.
  • FrontWiper On Hi: Windshield wiper switch is in the HI position.
  • FrontWiperI NT Auto On: Windshield wiper switch is in the INT position.
 -
F_WIP_ANG_SE_N_FAIL Not_Failure/Failure
  • Not_Failure: Position sensor in the windshield wiper motor is normal.
  • Failure: Position sensor in the windshield wiper motor has a malfunction.
 -
F_WIP_CTRL F.WiperOff/F.WiperLo/F.WiperHi
  • F.WiperOff: Windshield wipers are not operated.
  • F.WiperLo: Windshield wipers are operated at low speed.
  • F.WiperHi: Windshield wipers are operated at high speed.
 -
F_WIP_FET_FAIL Not_Failure/Failure
  • Not_Failure: FET circuit is normal.
  • Failure: FET circuit has a malfunction.
 -
F_WIP_INT_VOL % Displays windshield wiper INT level signal value received -
F_WIP_POS Unknown/Parking_Position/Not_Parking_Position
  • Unknown: Windshield wipers position is not determined.
  • Parking_Position: Windshield wipers in park position.
  • Not_Parking_Position: Windshield wipers in position other than park.
 -
F_WIP_REG_FAI_L Not_Failure/Failure
  • Not_Failure: Windshield wiper regulator is normal.
  • Failure: Windshield wiper regulator is not normal.
 -
F_WIP_REQ Off/Stop(ParkingPosition)/F.WiperLo/F.WiperHi/Stop(ServicePosition)/Stop(CurrentPosition)
  • Off: Body control module (BCM) does not operate windshield wipers.
  • Stop(Parking Position): Body control module (BCM) operates windshield wipers to the park position.
  • F.WiperLo: Body control module (BCM) operates windshield wipers at low speed.
  • F.WiperHi: Body control module (BCM) operates windshield wipers at high speed.
  • Stop(Service Position): Body control module (BCM) operates windshield wipers to the service position.
  • Stop(Current Position): Body control module (BCM) operates windshield wipers to the current position.
 -
F_WIP_ROT_FAI_L Not_Failure/Failure
  • Not_Failure: Windshield wiper rotation direction is normal.
  • Failure: Windshield wiper rotation direction is not normal.
 -
F_WIP_TEACH_STAT_SUB No_Sub_Status/Detect_jig_out_of_area/Unusually_Mode_Switch/DataFlash_Failure/FrontWipr_Failure/Not_detect_jig
  • No_Sub_Status: Body control module (BCM) cannot receive any signal from windshield wiper arm and blade.
  • Detect_jig_out_of_area: Windshield wiper arm and blade movement is detected to be outside of specified range.
  • Unusually_Mode_Switch: Windshield wiper and washer switch is not normal.
  • DataFlash_Failure: Data is not normal.
  • FrontWipr_Failure: Windshield wipers are malfunctioning.
 -
F_WIP_THRM_FAIL Not_Failure/Failure
  • Not_Failure: Circuit detecting windshield wiper motor temperature is not normal.
  • Failure: Circuit detecting windshield wiper motor temperature is normal.
 -
F_WIP_TIME_FAIL Not_Failure/Failure
  • Not_Failure: Windshield wiper is operating normally.
  • Failure: Windshield wiper operating speed is extremely slow (when the Windshield wiper is operating).
 -
F_WIP_VOLT_FAIL Not_Failure/Failure
  • Not_Failure: Circuit detecting windshield wiper motor voltage is not normal.
  • Failure: Circuit detecting windshield wiper motor voltage is normal.
 -
FR_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Front radar sensor is not equipped.
  • Node Attached and Communicate correctly: Front radar sensor is equipped, communication with front radar sensor is normal.
  • NodeAttached but Not Communicate correctly: Front radar sensor is equipped, but communication with front radar sensor is not normal.
 -
FSC_LGHT_REQ Off/On
  • Off: Headlight HI is turned on.
  • On: Headlight HI is turned off.
 -
FSC_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Forward sensing camera (FSC) is not equipped.
  • Node Attached and Communicate correctly: Forward sensing camera (FSC) is equipped, communication with forward sensing camera (FSC) is normal.
  • NodeAttached but Not Communicate correctly: Forward sensing camera (FSC) is equipped, but communication with forward sensing camera (FSC) is not normal.
 -
FSM_REQ Off/On
  • Off: Front side marker light is turned on.
  • On: Front side marker light is turned off.
 -
FSRL_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Front side radar sensor (LH) is not equipped.
  • Node Attached and Communicate correctly: Front side radar sensor (LH) is equipped, communication with front side radar sensor (LH) is normal.
  • NodeAttached but Not Communicate correctly: Front side radar sensor (LH) is equipped, but communication with front side radar sensor (LH) is not normal.
 -
FSRR_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Front side radar sensor (RH) is not equipped.
  • Node Attached and Communicate correctly: Front side radar sensor (RH) is equipped, communication with front side radar sensor (RH) is normal.
  • NodeAttached but Not Communicate correctly: Front side radar sensor (RH) is equipped, but communication with front side radar sensor (RH) is not normal.
 -
FUEL_AMOUNT L Displays fuel level detected by the fuel gauge 2A, 2B, 2C, 2D, 2E, 2F, 2G, 2H, 2J, 2L, 3S, 3T, 3U, 3V, 3W, 3X, 4M, 4N, 4Q, 4R
FUEL_GAUGE_RES_MAIN Ohm Displays fuel gauge sender unit resistance value 2A, 2B, 2C, 2D, 2E, 2F, 2G, 2H, 2J, 2L, 3S, 3T, 3U, 3V, 3W, 3X, 4M, 4N, 4Q, 4R
FUEL_GAUGE_RES_SUB Ohm Displays fuel gauge sender unit (sub) resistance value 2A, 2B, 2C, 2D, 2E, 2F, 2G, 2H, 2J, 2L, 3S, 3T, 3U, 3V, 3W, 3X, 4M, 4N, 4Q, 4R
FUEL_GAUGE_VOLT_MAIN V Displays fuel gauge sender unit voltage value 2A, 2B, 2C, 2D, 2E, 2F, 2G, 2H, 2J, 2L, 3S, 3T, 3U, 3V, 3W, 3X, 4M, 4N, 4Q, 4R
FUEL_GAUGE_VOLT_SUB V Displays fuel gauge sender unit (sub) voltage value 2A, 2B, 2C, 2D, 2E, 2F, 2G, 2H, 2J, 2L, 3S, 3T, 3U, 3V, 3W, 3X, 4M, 4N, 4Q, 4R
GLOBAL_REAL_TIME min Displays cumulative elapsed time since vehicle completion -
GLOWPLUG_NETWORK
NOTE:
  • Displays in the M-MDS but it does not operate.
H/L_CLEAN_RLY
NOTE:
  • Displays in the M-MDS but it does not operate.
H/L_HI Off/On
  • Off: Headlight HI signal is not sent from body control module (BCM).
  • On: Headlight HI signal is sent from body control module (BCM).
 -
H/L_HI_SW Off/On
  • Off: Light switch HI signal is not received.
  • On: Light switch HI signal is received.
 -
H/L_LO_REQ Off/On
  • Off: Body control module (BCM) does not operate the headlight LO off.
  • On:Body control module (BCM) does not operate the headlight LO on.
 -
H/L_LO_SW Off/On
  • Off: Other than light switch LO position of light switch is received.
  • On: Light switch LO position of light switch is received.
 -
H/L_LVL_CSTMZ Not Adopted/0/0.5/1/1.5/2/2.5/3/3.5/4/4.5/5 Display headlight manual leveling system set position. -
H/L_OFF_SW Off/On
  • Off: Light switch OFF signal is not received.
  • On: Light switch OFF signal is received.
 -
H/L_PASSING_SW Off/On
  • Off: Light switch FLASH-TO-P ASS signal is not received.
  • On: Light switch FLASH-TO-P ASS signal is received.
 -
HOOD_SW Close/Open
  • Close: Hood is closed.
  • Open: Hood is open.
 2S
HUD_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Active Driving Display (ADD) is not equipped.
  • Node Attached and Communicate correctly: Active Driving Display (ADD) is equipped, communication with Active Driving Display (ADD) is normal.
  • NodeAttached but Not Communicate correctly: Active Driving Display (ADD) is equipped, but communication with Active Driving Display (ADD) is not normal.
 -
HZRD_REQ NoRequest/RequestControl
  • NoRequest: Body control module (BCM) does not operate the hazard warning light on.
  • RequestControl: Body control module (BCM) operates the hazard warning light on.
 -
HZRD_SW Off/On/Unknown
  • Off: Hazard warning switch is not pressed.
  • On: Hazard warning switch is pressed.
  • Unknown: Hazard warning switch on/off is not determined.
 -
ICM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Instrument cluster is not equipped.
  • Node Attached and Communicate correctly: Instrument cluster is equipped, communication with instrument cluster is normal.
  • NodeAttached but Not Communicate correctly: Instrument cluster is equipped, but communication with instrument cluster is not normal.
 -
IG_ON_TIMER Min Time since engine start -
IG1_RLY Off/On
  • Off: IG1 relay drive is off.
  • On: IG1 relay drive is on.
 -
IMMOBI_IDENTIFY
NOTE:
  • Displays in the M-MDS but it does not operate.
IMMOBI_OPERAT_MODE Operation Mode 1/Operation Mode 2/Operation Mode 3/Operation Mode 4/Operation Mode 5/Operation Mode 6/Operation Mode 7 Displays immobilizer system operation mode -
IMMOBI_SYS_STAT - Displays immobilizer system condition -
IMS_NETWORK
NOTE:
  • Displays in the M-MDS but it does not operate.
IND_ASSY_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Indicator unit is not equipped.
  • Node Attached and Communicate correctly: Indicator unit is equipped, communication with indicator unit is normal.
  • NodeAttached but Not Communicate correctly: Indicator unit is equipped, but communication with indicator unit is not normal.
 -
IP-ESU_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Climate control unit is not equipped.
  • Node Attached and Communicate correctly: Climate control unit is equipped, communication with climate control unit is normal.
  • NodeAttached but Not Communicate correctly: Climate control unit is equipped, but communication with climate control unit is not normal.
 -
KEY_ANS_REQ NoRequest/RequestControl
  • NoRequest: Hazard warning light flashing answer-back signal is not received.
  • RequestControl: Hazard warning light flashing answer-back signal is received.
 -
KEY_BUZZER Off/On
  • Off: Keyless beeper is not operated to sound.
  • On: Keyless beeper is operated to sound.
 2AA, 2AB
KEY_ENA Disabled/Enabled
  • Disabled: Immobilizer system is disabled.
  • Enabled: Immobilizer system is enabled.
 -
KEY_INFO_1 - Displays vehicle information 1 sent from body control module (BCM) to LF control unit. -
KEY_INFO_2 - Displays vehicle information 2 sent from body control module (BCM) to LF control unit. -
LATCH_IP_SW Off/On
  • Off: Power liftgate (PLG) front switch is not pressed.
  • On: Power liftgate (PLG) front switch is pressed.
 -
LCML_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Light control module (LH) is not equipped.
  • Node Attached and Communicate correctly: Light control module (LH) is equipped, communication with light control module (LH) is normal.
  • NodeAttached but Not Communicate correctly: Light control module (LH) is equipped, but communication with light control module (LH) is not normal.
 -
LCMR_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Light control module (RH) is not equipped.
  • Node Attached and Communicate correctly: Light control module (RH) is equipped, communication with light control module (RH) is normal.
  • NodeAttached but Not Communicate correctly: Light control module (RH) is equipped, but communication with light control module (RH) is not normal.
 -
LFU_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: LF control unit is not equipped.
  • Node Attached and Communicate correctly: LF control unit is equipped, communication with LF control unit is normal.
  • NodeAttached but Not Communicate correctly: LF control unit is equipped, but communication with LF control unit is not normal.
 -
LLINK_SW_D Unlock/Neutral/Lock/Failure
  • Unlock: Front door lock-link switch (driver's side) is in unlock.
  • Neutral: Front door lock-link switch (driver's side) is not in lock and unlock.
  • Lock: Front door lock-link switch (driver's side) is in lock.
  • Failure: Front door lock-link switch (driver's side) has a malfunction.
 -
LINK_SW_P Unlock/Lock
  • Unlock: Front door lock-link switch (passenger's side) is in unlock.
  • Lock: Front door lock-link switch (passenger's side) is in lock.
 -
LLINK_SW_R Unlock/Lock
  • Unlock: Rear door lock-link switch (LH), rear door lock-link switch (RH) are in unlock.
  • Lock: Rear door lock-link switch (LH), rear door lock-link switch (RH) are in lock.
 4F
LLINK_SW_STATR Off/On
  • Off: Front door lock-link switch (LH) is in unlock.
  • On: Front door lock-link switch (LH) is in lock.
 -
MASTER_KEY No/Yes
  • No: There is no master key.
  • Yes: There is master key.
 -
MODE_ACTAT_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Airflow mode actuator is not equipped.
  • Node Attached and Communicate correctly: Airflow mode actuator is equipped, communication with airflow mode actuator is normal.
  • NodeAttached but Not Communicate correctly: Airflow mode actuator is equipped, but communication with airflow mode actuator is not normal.
 -
MODE_PS_ACT_AT_NETWORK
NOTE:
  • Displays in the M-MDS but it does not operate.
MTTR_TIMER hour If the ignition is switched OFF after a specified time has elapsed or the vehicle has been driven for a specified period of time or more while in the failsafe mode, the ignition will remain switched off and the engine cannot be started. Displays the elapsed time since the engine could no longer be started. -
NOX1_NETWORK
NOTE:
  • Displays in the M-MDS but it does not operate.
NOX2_NETWORK
NOTE:
  • Displays in the M-MDS but it does not operate.
OHC_ROOMLAMP_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Front map light is not equipped.
  • Node Attached and Communicate correctly: Front map light is equipped, communication with front map light is normal.
  • NodeAttached but Not Communicate correctly: Front map light is equipped, but communication with front map light is not normal.
 -
OIL_LVL_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Engine oil level sensor is not equipped.
  • Node Attached and Communicate correctly: Engine oil level sensor is equipped, communication with engine oil level sensor is normal.
  • NodeAttached but Not Communicate correctly: Engine oil level sensor is equipped, but communication with engine oil level sensor is not normal.
 -
OMC_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Driver monitoring camera unit is not equipped.
  • Node Attached and Communicate correctly: Driver monitoring camera unit is equipped, communication with driver monitoring camera unit is normal.
  • NodeAttached but Not Communicate correctly: Driver monitoring camera unit is equipped, but communication with driver monitoring camera unit is not normal.
 -
OMM_LGHT_OFF Off/On
  • Off: Battery discharge suppression signal is not sent from body control module (BCM).
  • On: Battery discharge suppression signal is sent from body control module (BCM).
 -
ONE_TOUCH_TURN Off/On
  • Off: Turn switch LH signal or the turn switch RH signal is not received.
  • On: Turn switch LH signal or the turn switch RH signal is received.
 -
OUTLET_L1_REQ Off/On
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
 -
OUTLET_R1_REQ Off/On
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
 -
PARK_RANGE_SW Off/On
  • Off: NOT P position switch is off.
  • On: NOT P position switch is on.
 -
PCM_PT_BUS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: PCM is not equipped.
  • Node Attached and Communicate correctly: PCM is equipped, communication via CAN BUS No. 2 with PCM is normal.
  • NodeAttached but Not Communicate correctly: PCM is equipped, but communication via CAN BUS No. 2 with is not normal.
 -
PCM_VEH_BUS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: PCM is not equipped.
  • Node Attached and Communicate correctly: PCM is equipped, communication via CAN BUS No. 1 with PCM is normal.
  • NodeAttached but Not Communicate correctly: PCM is equipped, but communication via CAN BUS No. 1 with is not normal.
 -
PLG_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Power liftgate (PLG) control module is not equipped.
  • Node Attached and Communicate correctly: Power liftgate (PLG) control module is equipped, communication with power liftgate (PLG) control module is normal.
  • NodeAttached but Not Communicate correctly: Power liftgate (PLG) control module is equipped, but communication with power liftgate (PLG) control module is not normal.
 -
PMS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Position memory control module is not equipped.
  • Node Attached and Communicate correctly: Position memory control module is equipped, communication with position memory control module is normal.
  • NodeAttached but Not Communicate correctly: Position memory control module is equipped, but communication with position memory control module is not normal.
 -
PNC_ALRM_HZRD NoRequest/RequestControl
  • Off: Hazard warning light flashing request signal is not received.
  • On: Hazard warning light flashing request signal is received.
 -
PNC_ALRM_REQ*5 NoRequest/RequestControl
  • Off: Hazard warning light flashing request signal is not received.
  • On: Hazard warning light flashing request signal is received.
 -
POWER_MODE OFF/ACC/ON/CRANK
  • OFF: Body control module (BCM) controls ignition switch off (lock).
  • ACC: Body control module (BCM) controls ignition switch ACC.
  • ON: Body control module (BCM) controls ignition switch ON (engine off).
  • CRANK: Body control module (BCM) controls cranking at ignition switch ON.
 -
PSM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Parking assist unit (ultrasonic) is not equipped.
  • Node Attached and Communicate correctly: Parking assist unit (ultrasonic) is equipped, communication with parking assist unit (ultrasonic) is normal.
  • NodeAttached but Not Communicate correctly: Parking assist unit (ultrasonic) is equipped, but communication with parking assist unit (ultrasonic) is not normal.
 -
PTC_HEAT_NET WORK
NOTE:
  • Displays in the M-MDS but it does not operate.
R_FOG_SW_IN
NOTE:
  • Displays in the M-MDS but it does not operate.
R_FOG_SW_OUT
NOTE:
  • Displays in the M-MDS but it does not operate.
R_MIX_ACTAT_NETWORK
NOTE:
  • Displays in the M-MDS but it does not operate.
R_TIMER_MODE OFF/ON
  • OFF: Intermittent wiper operation of rear wiper is disabled.
  • Intermittent wiper operation of rear wiper is enabled.
 -
R_VENT_ACTAT_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Rear vent actuator is not equipped.
  • Node Attached and Communicate correctly: Rear vent actuator is equipped, communication with rear vent actuator is normal.
  • NodeAttached but Not Communicate correctly: Rear vent actuator is equipped, but communication with rear vent actuator is not normal.
 -
R_WASH_SW Off/On
  • Off: Rear wiper and washer switch is not in rear washer position.
  • On: Rear wiper and washer switch is in rear washer position.
 -
R_WIP Off/RearWiperLo/Not defined/WiperINT
  • Off: Rear wiper and washer switch is in the OFF position.
  • RearWiperLo: Rear wiper and washer switch is in the ON position.
  • Not defined: Rear wiper and washer switch position is not determined.
  • WiperINT: Rear wiper and washer switch is in the INT position.
 -
R_WIP_CTRL Deactivate/Activate/Fail(Circuit Short to Ground)/Fail(Circuit Open)/Fail(Circuit Short to Battery) Rear wiper operation condition input signal from electrical supply unit (ESU)
  • Deactivate: Rear wiper is not operated.
  • Activate: Rear wiper is operated.
  • Fail(Circuit Short to Ground): Short to ground circuit malfunction is received from rear wiper.
  • Fail(Circuit Open): Open circuit malfunction is received from rear wiper.
  • Fail(Circuit Short to Battery): Short to battery circuit malfunction is received from rear wiper.
 -
R_WIP_POS Unknown/Parking_Position/Not_Parking_Position/AS_SW_Failure
  • Unknown: Rear wiper position is not determined.
  • Parking_Position: Rear wiper in park position.
  • Not_Parking_Position: Rear wiper in position other than park.
  • AS_SW_Failure: Autostop switch has a malfunction.
 -
R_WIP_REQ Off/Rear Wiper Low On/Stop
  • Off: Body control module (BCM) does not operate rear wiper.
  • Rear Wiper Low On: Body control module (BCM) operates rear wiper.
  • Stop: Body control module (BCM) operates rear wiper to the park position.
 -
R_WIP_STALL_STAT OK/Stall
  • OK: Rear wiper motor is normal.
  • Stall: Rear wiper motor is stalled.
 -
RCM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Sophisticated Airbag Sensor (SAS) control module is not equipped.
  • Node Attached and Communicate correctly: Sophisticated Airbag Sensor (SAS) control module is equipped, communication with Sophisticated Airbag Sensor (SAS) control module is normal.
  • NodeAttached but Not Communicate correctly: Sophisticated Airbag Sensor (SAS) control module is equipped, but communication with Sophisticated Airbag Sensor (SAS) control module is not normal.
 -
REGEN_NETWORK
NOTE:
  • Displays in the M-MDS but it does not operate.
RES Off/On
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
 -
RES_HZRD_ANS NoRequest/RequestControl
  • NoRequest: Hazard warning light flashing answer-back signal is not received.
  • RequestControl: Hazard warning light flashing answer-back signal is received.
 -
RF_TMTR FALSE/TRUE
  • FALSE: Remote transmitter ID information is not programmed in LF control unit.
  • TRUE: Remote transmitter ID information is programmed in LF control unit.
 -
RLS_AMB_TEMP °C, °F Displays rain sensor ambient temperature. -
RLS_AUTO_LGHT_REQ TNSOff/Head_Off/TNSOn/HeadOff/TNSOn/HeadOn Illumination request by receiving TNS or headlight illumination request signal.
  • TNSOff/Head_Off: Body control module (BCM) does not operate the TNS (parking lights) and headlight on.
  • TNSOn/Head Off:Body control module (BCM) operates the TNS (parking lights) on.
  • TNSOn/Head On: Body control module (BCM) operates the TNS (parking lights) and headlight on.
 -
RLS_CTRL OFF/TNS Only ON/Low and TNS/Unknown Illumination request by receiving auto light signal, TNS or headlight illumination request signal.
  • OFF: Body control module (BCM) does not operate the TNS (parking lights) and headlight on.
  • TNS Only ON:Body control module (BCM) operates the TNS (parking lights) on.
  • Low and TNS: Body control module (BCM) operates the TNS (parking lights) and headlight on.
  • Unknown: TNS (parking lights) condition is not detected.
 -
RLS_FAIL Normal/Fault
  • Normal: Error signals is not received from the auto light sensor.
  • Fault: Error signals is received from the auto light sensor.
 -
RLS_FAIL_STAT Faulty(Faulty)/Initialize/Not within specifications/Normal(sensing) Displays auto light sensor condition input signal -
RLS_FWD_LGHT_SEN OK/NG
  • OK: Normal forward brightness can be detected.
  • NG: Normal forward brightness cannot be detected.
 -
RLS_I_ILLMI_MODE Unknown/Off(day_mode)/On(night_mode)
  • Unknown: Panel light illumination request signal is not determined.
  • Off(day_mode): Panel light illumination request signal is not received.
  • On(night_mode): Panel light illumination request signal is received.
 -
RLS_LGHT_SEN_FAIL Normal/Fault
  • Normal: Error signals is not received from the auto light sensor.
  • Fault: Error signals is received from the auto light sensor.
 -
RLS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Humidity sensor/solar radiation sensor/auto light sensor/rain sensor is not equipped.
  • Node Attached and Communicate correctly: Humidity sensor/solar radiation sensor/auto light sensor/rain sensor is equipped, communication with humidity sensor/solar radiation sensor/auto light sensor/rain sensor is normal.
  • NodeAttached but Not Communicate correctly: Humidity sensor/solar radiation sensor/auto light sensor/rain sensor is equipped, but communication with humidity sensor/solar radiation sensor/auto light sensor/rain sensor is not normal.
 -
RLS_RAIN_SEN_FAIL Off/On
  • Off: Error signals is not received from the rain sensor.
  • On: Error signals is received from the rain sensor.
 -
RLS_RELAT_HM_DTY % Displays relative humidity. -
RLS_STAT Off/TNS On requested/TNS/Headlight On requested
  • Off: TNS (parking lights) and headlight illumination request signal is not received.
  • TNS On requested: TNS (parking lights) illumination request signal is received.
  • TNS/Headlight On requested: TNS (parking lights) and headlight illumination request signal is received.
 -
RLS_TEMP_SEN_FAIL Normal/Fault
  • Normal: Error signals is not received from the temperature sensor (built into humidity sensor).
  • Fault: Error signals is received from the temperature sensor (built into humidity sensor).
 -
RLS_UP_LGHT_SEN OK/NG
  • OK: Normal upward brightness can be detected.
  • NG: Normal upward brightness cannot be detected.
 -
RLS_VOLT_FAIL Normal/Fault
  • Normal: Power supply voltage of humidity sensor/solar radiation sensor/auto light sensor/rain sensor is normal.
  • Fault: Power supply voltage of humidity sensor/solar radiation sensor/auto light sensor/rain sensor is not normal.
 -
RLS_WINDOW_TEMP °C, °F Displays windshield temperature. -
RLS_WIP_REQ WiperOFF/WiperOff_duringAutoINT/Single Wipe/SpeedLow/SpeedHigh/Failure
  • WiperOFF: Wiper operation signal is not received from rain sensor.
  • WiperOff_duringAutoINT: Error signals is received from the rain sensor.
  • Single Wipe: Signal to operate wiper once is received from rain sensor.
  • SpeedLow: Signal to operate wiper at low speed is received from rain sensor.
  • SpeedHigh: Signal to operate wiper at high speed is received from rain sensor.
  • Failure: Communication with rain sensor is failed.
 -
RSRL_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Rear side radar sensor (LH) is not equipped.
  • Node Attached and Communicate correctly: Rear side radar sensor (LH) is equipped, communication with rear side radar sensor (LH) is normal.
  • NodeAttached but Not Communicate correctly: Rear side radar sensor (LH) is equipped, but communication with rear side radar sensor (LH) is not normal.
 -
RSRR_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Rear side radar sensor (RH) is not equipped.
  • Node Attached and Communicate correctly: Rear side radar sensor (RH) is equipped, communication with rear side radar sensor (RH) is normal.
  • NodeAttached but Not Communicate correctly: Rear side radar sensor (RH) is equipped, but communication with rear side radar sensor (RH) is not normal.
 -
S_BELT_LED_OFF_C/R Off/On
  • Off: Rear seat belt (center) warning light (red) is not illuminated.
  • On: Rear seat belt (center) warning light (red) is illuminated.
 -
S_BELT_LED_OFF_L/R Off/On
  • Off: Rear seat belt (LH) warning light (red) is not illuminated.
  • On: Rear seat belt (LH) warning light (red) is illuminated.
 -
S_BELT_LED_OFF_R/R Off/On
  • Off: Rear seat belt (RH) warning light (red) is not illuminated.
  • On: Rear seat belt (RH) warning light (red) is illuminated.
 -
S_BELT_LED_ON_C/R Off/On
  • Off: Rear seat belt (center) warning light (green) is not illuminated.
  • On: Rear seat belt (center) warning light (green) is illuminated.
 -
S_BELT_LED_ON_L/R Off/On
  • Off: Rear seat belt (LH) warning light (green) is not illuminated.
  • On: Rear seat belt (LH) warning light (green) is illuminated.
 -
S_BELT_LED_ON_R/R Off/On
  • Off: Rear seat belt (RH) warning light (green) is not illuminated.
  • On: Rear seat belt (RH) warning light (green) is illuminated.
 -
S_BELT_LED_P Off/On
  • Off: Passenger seat belt warning light is not illuminated.
  • On: Passenger seat belt warning light is illuminated.
 -
S_BELT_STAT Vaild/Unknown
  • Vaild: All rear seat belt warning light signals are normal.
  • Unknown: There is a rear seat belt warning light signal error.
 -
S_BELT_STAT_C/3RD
NOTE:
  • Displays in the M-MDS but it does not operate.
S_BELT_STAT_C/R RearCenter belt not used (Close)/RearCenter belt used (Open)
  • RearCenter belt not used(Close): Rear center seat belt is not fastened.
  • RearCenter belt used(Open): Rear center seat belt is fastened.
 -
S_BELT_STAT_L/3RD
NOTE:
  • Displays in the M-MDS but it does not operate.
S_BELT_STAT_L/R RearLeft belt not used(Close)/RearLeft belt used(Open)
  • RearLeft belt not used(Close): Rear left seat belt is not fastened.
  • RearLeft belt used(Open): Rear left seat belt is fastened.
 -
S_BELT_STAT_R/3RD
NOTE:
  • Displays in the M-MDS but it does not operate.
S_BELT_STAT_R/R RearRight belt not used(Close)/RearRight belt not used(Open)
  • RearRight belt not used(Close): Rear right seat belt is not fastened.
  • RearRight belt used(Open): Rear right seat belt is fastened.
 -
S_BELT_WRNG_D driver belt not used/driver belt used/fault(hole IC switch)/resrve(mech switch)
  • driver belt not used:Driver seat belt is not fastened.
  • driver belt used: Driver seat belt is fastened.
  • fault(hole IC switch)/resrve(mech switch): Driver seat belt has a malfunction.
 -
S_BELT_WRNG_P driver belt not used/driver belt used/fault(hole IC switch)/resrve(mech switch)
  • driver belt not used: Passenger seat belt is not fastened.
  • driver belt used: Passenger seat belt is fastened.
  • fault(hole IC switch)/resrve(mech switch): Passenger seat belt has a malfunction.
 -
SAS_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Steering angle sensor is not equipped.
  • Node Attached and Communicate correctly: Steering angle sensor is equipped, communication with steering angle sensor is normal.
  • NodeAttached but Not Communicate correctly: Steering angle sensor is equipped, but communication with steering angle sensor is not normal.
 -
SCR_HZRD_REQ Off/On
  • Off: Secondary collision reduction hazard warning light is not operated.
  • On: Secondary collision reduction hazard warning light is operated.
 -
SEAT_LETER_ILLMI Off/On
  • Off: Passenger air bag deactivation (PAD) lettering illumination is not illuminated.
  • On: Passenger air bag deactivation (PAD) lettering illumination is illuminated.
 -
SEAT_OCS_C/R
NOTE:
  • Displays in the M-MDS but it does not operate.
SEAT_OCS_L/R
NOTE:
  • Displays in the M-MDS but it does not operate.
SEAT_OCS_R/R
NOTE:
  • Displays in the M-MDS but it does not operate.
SEAT_OCS_STAT
NOTE:
  • Displays in the M-MDS but it does not operate.
SHIFT between 2 positions/P/R/N/D/S(2)/L(1)
  • between 2 positions: Selector lever is between two positions.
  • P: Selector lever is in P position.
  • R: Selector lever is in R position.
  • N: Selector lever is in N position.
  • D: Selector lever is in D position.
  • S(2): Selector lever is in D position 2nd gear.
  • L(1): Selector lever is in D position 1st gear.
 -
SLAM_LCK Off/On
  • On: With all of the following conditions met, lock knob on door equipped with door lock-link switch is locked and all doors are closed.
  • Ignition is switched OFF
  • Any door is open
  • Off: Conditions other than above
 -
SPARE_KEY_STAT Off/On
  • Off: There is no spare key.
  • On: There is spare key.
 -
SSB_1 Off/On
  • Off: Push button start switch 1 is off.
  • On: Push button start switch 1 is on.
 -
SSB_2 Off/On
  • Off: Push button start switch 2 is off.
  • On: Push button start switch 2 is on.
 -
SSB_AMBER_REQ Off/On
  • Off: Push button start indicator light (amber) is turned off.
  • On: Push button start indicator light (amber) is illuminated.
 -
SSB_GREEN_REQ Off/On
  • Off: Push button start indicator light (green) is turned off.
  • On: Push button start indicator light (green) is illuminated.
 -
SSB_ILLMI_REQ Off/On
  • Off: START/STOP/ENGINE indicator light is turned off.
  • On: START/STOP/ENGINE indicator light is illuminated.
 -
SSU_RES_NUM 0/1/2/3
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
 -
SSU_RES_STAT Disable/Enable
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
 -
STR_ANG ° (deg) Displays steering angle signal (absolute angle)
  • Steering wheel in neutral position: Near 0 degrees
  • Steering wheel turned to left: Changes from 0 degrees to positive
  • Steering wheel turned to right: Changes from 0 degrees to negative
 -
STR_COLM_LCK_CTRL
NOTE:
  • Displays in the M-MDS but it does not operate.
STR_COLM_LCK_GND
NOTE:
  • Displays in the M-MDS but it does not operate.
STR_COLM_LCK_POWER
NOTE:
  • Displays in the M-MDS but it does not operate.
STR_COLM_LCK_STAT
NOTE:
  • Displays in the M-MDS but it does not operate.
TR_COLM_LCK_SW
NOTE:
  • Displays in the M-MDS but it does not operate.
STR_COLM_LCK_SW_MEMORY
NOTE:
  • Displays in the M-MDS but it does not operate.
STR_COLM_ULCK_SW
NOTE:
  • Displays in the M-MDS but it does not operate.
STR_COLM_ULCK_SW_MEMORY
NOTE:
  • Displays in the M-MDS but it does not operate.
STR_HEAT_NET WORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Heated steering wheel control unit is not equipped.
  • Node Attached and Communicate correctly: Heated steering wheel control unit is equipped, communication with heated steering wheel control unit is normal.
  • NodeAttached but Not Communicate correctly: Heated steering wheel control unit is equipped, but communication with heated steering wheel control unit is not normal.
 -
SUPER_LCK_ALL Off/On
  • Off: Double locking function (With double locking) is not operated.
  • On: Double locking function (With double locking) is operated.
 2J, 2L
T/LGT_LCK_SW Off/On
  • Off: Door lock switch (liftgate) is off.
  • On: Door lock switch (liftgate) is on.
 4I
T/LGT_SW Close/Open
  • Close: Liftgate is closed.
  • Open: Liftgate is open.
 2J, 2L
T/LGT_ULCK Off/On
  • Off: Body control module (BCM) does not operate the liftgate to unlock.
  • On: Body control module (BCM) operates the liftgate to unlock.
 2J, 2L
TCM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: TCM is not equipped.
  • Node Attached and Communicate correctly: TCM is equipped, communication with TCM is normal.
  • NodeAttached but Not Communicate correctly: TCM is equipped, but communication with TCM is not normal.
 -
TCM_PT2_NET WORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: TCM is not equipped.
  • Node Attached and Communicate correctly: TCM is equipped, communication via CAN BUS No. 2 with TCM is normal.
  • NodeAttached but Not Communicate correctly: TCM is equipped, but communication via CAN BUS No. 2 with TCM is not normal.
 -
TCU_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Telematics communication unit is not equipped.
  • Node Attached and Communicate correctly: Telematics communication unit is equipped, communication with telematics communication unit is normal.
  • NodeAttached but Not Communicate correctly: Telematics communication unit is equipped, but communication with telematics communication unit is not normal.
 -
TEMP_LH_ACTAT_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Driver-side air mix actuator is not equipped.
  • Node Attached and Communicate correctly: Driver-side air mix actuator is equipped, communication with driver-side air mix actuator is normal.
  • NodeAttached but Not Communicate correctly: Driver-side air mix actuator is equipped, but communication with driver-side air mix actuator is not normal.
 -
TEMP_RH_ACTAT_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Passenger-side air mix actuator is not equipped.
  • Node Attached and Communicate correctly: Passenger-side air mix actuator is equipped, communication with passenger-side air mix actuator is normal.
  • NodeAttached but Not Communicate correctly: Passenger-side air mix actuator is equipped, but communication with passenger-side air mix actuator is not normal.
 -
TGT_VERIFY Error/OK Displays immobilizer system condition. -
TIRE_PRES_L/F kPa Displays tire pressure (wheel unit (LF)) -
TIRE_PRES_L/R kPa Displays tire pressure (wheel unit (LR)) -
TIRE_PRES_R/F kPa Displays tire pressure (wheel unit (RF)) -
TIRE_PRES_R/R kPa Displays tire pressure (wheel unit (RR)) -
TIRE_TEMP_L/F °C, °F Displays tire temperature (wheel unit (LF)) -
TIRE_TEMP_L/R °C, °F Displays tire temperature (wheel unit (LR)) -
TIRE_TEMP_R/F °C, °F Displays tire temperature (wheel unit (RF)) -
TIRE_TEMP_R/R °C, °F Displays tire temperature (wheel unit (RR)) -
TMTR_NUM 0/1/2/3/4/5/6 Displays registration number of the remote transmitter -
TNS_REQ Off/On
  • Off: Body control module (BCM) does not operate the TNS (parking lights) on.
  • On: Body control module (BCM) operates the TNS (parking lights) on.
 -
TNS_SW Off/On
  • Off: Light switch TNS (parking lights) signal is not received.
  • On: Light switch TNS (parking lights) signal is received.
 -
TOPOLOGY_ID - Displays topological ID -
TOTAL_DIST km, ft, mi Displays total traveled distance -
TPMS_FAIL Default/Zero Learnt/One Learnt/Two Learnt/Three Learnt/ABS Error/Maximum speed exceeded/Location not determined/Locate data issue Displays reason why tire position recognition failed. -
TPMS_MODE_L/F Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode Displays wheel unit (LF) mode -
TPMS_MODE_L/R Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode Displays wheel unit (LR) mode -
TPMS_MODE_R/F Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode Displays wheel unit (RF) mode -
TPMS_MODE_R/R Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode Displays wheel unit (RR) mode -
TUNER_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Remote tuner (RT) is not equipped.
  • Node Attached and Communicate correctly:Re mote tuner (RT) is equipped, communication with remote tuner (RT) is normal.
  • NodeAttached but Not Communicate correctly: Remote tuner (RT) is equipped, but communication with remote tuner (RT) is not normal.
 -
TURN_L Off/On
  • Off: Turn switch LH signal is not sent from body control module (BCM).
  • On: Turn switch LH signal is sent from body control module (BCM).
 -
TURN_L_INTERIOR Off/On
  • Off: Turn signal (LH) or hazard warning indicator signal is not sent from body control module (BCM).
  • On: Turn signal (LH) or hazard warning indicator signal is sent from body control module (BCM).
 -
TURN_R Off/On
  • Off: Turn switch RH signal is not sent from body control module (BCM).
  • On: Turn switch RH signal is sent from body control module (BCM).
 -
TURN_R_INTERIOR Off/On
  • Off: Turn signal (RH) or hazard warning indicator signal is not sent from body control module (BCM).
  • On: Turn signal (RH) or hazard warning indicator signal is sent from body control module (BCM).
 -
TURN_SW Turn Off/Turn Right ON/Turn Left ON/Unknown
  • Turn Off: Turn switch is in OFF position.
  • Turn Right ON: Turn switch is in RH position.
  • Turn Left ON: Turn switch is in LH position.
  • Unknown: Turn switch position is not determined.
 -
USBHUB_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Auxiliary jack/usb port/sd card slot hub is not equipped.
  • Node Attached and Communicate correctly: Auxiliary jack/usb port/sd card slot hub is equipped, communication with auxiliary jack/usb port/sd card slot hub is normal.
  • NodeAttached but Not Communicate correctly: Auxiliary jack/usb port/sd card slot hub is equipped, but
  • communication with auxiliary jack/usb port/sd card slot hub is not normal.
 -
VCM_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Vehicle control module (VCM) is not equipped.
  • Node Attached and Communicate correctly: Vehicle control module (VCM) is equipped, communication with vehicle control module (VCM) is normal.
  • NodeAttached but Not Communicate correctly: Vehicle control module (VCM) is equipped, but communication with vehicle control module (VCM) is not normal.
 -
VDT_MODE Normal Mode/Manual Trigger Mode/i-ActivSense Analysis Mode/Reject Mode
  • Normal Mode: Vehicle is in normal mode.
  • Manual Trigger Mode: Vehicle is in driving data collecting mode.
  • i-ActivSense Analysis Mode: Vehicle is in i-ACTIVSENSE data collecting mode.
  • Reject Mode: Restricted remote operation and data transfer.
 -
VMC_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: 360°view monitor control module/parking assist unit (optical) is not equipped.
  • Node Attached and Communicate correctly: 360°view monitor control module/parking assist unit (optical) is equipped, communication with 360°view monitor control module/parking assist unit (optical) is normal.
  • NodeAttached but Not Communicate correctly: 360°view monitor control module/parking assist unit (optical) is equipped, but communication with 360°view monitor control module/parking assist unit (optical) is not normal.
 -
VPWR_ACC V Displays voltage at body control module (BCM) terminal 2AE (ACC power supply) 2AE
VPWR_CBCM V Displays power supply voltage of body control module (BCM) -
VPWR_ESCL V Displays voltage at body control module (BCM) terminal 4W (power supply) 4W
VPWR_IG V Displays voltage at body control module (BCM) terminal 2AF (ignition power supply) 2AF
VPWR_LIMP_HOME V Displays voltage at body control module (BCM) terminal 1B (power supply) 1B
VPWR_ROOM V Displays voltage at body control module (BCM) terminal 1D (power supply) 1D
WASH_MOTOR_STAT Off/Washer_Motor_L/Washer_Motor_R
  • Off: Windshield washer motor relay and rear washer motor relay are off.
  • Washer_Motor_L: Windshield washer motor relay is on.
  • Washer_Motor_R: Rear washer motor relay is on.
 -
WIP_NETWORK Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
  • Node is not attached on Vehicle: Windshield wiper motor is not equipped.
  • Node Attached and Communicate correctly: Windshield wiper motor is equipped, communication with windshield wiper motor is normal.
  • NodeAttached but Not Communicate correctly: Windshield wiper motor is equipped, but communication with windshield wiper motor is not normal.
 -
scientia non olet · About LEMON Manuals