Common Specs & Procedures Index
CX-3 COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | TECHNICAL DATA - HVAC | ||
| Torque | See Torque Specifications in Text and applicable graphics in BASIC SYSTEM - HVAC |
||
| Axle Nut/Hub Nut | Step 1: 74-110 Ft. Lbs. (100-150 N.m) Step 2: Loosen 180 degrees Step 3: 175-202 Ft. Lbs. (236-274 N.m) |
||
| Battery | BATTERY INSPECTION | ||
| Brakes | |||
| Bleeding Sequence | BRAKE FLUID AIR BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | TECHNICAL DATA - BRAKES | ||
| Torque | See Torque Specifications in Text and applicable graphics in CONVENTIONAL BRAKE SYSTEM |
||
| Charging | |||
| Generator | GENERATOR INSPECTION | ||
| Torque | See Torque Specifications in Text and applicable graphics in CHARGING SYSTEM |
||
| Drive Belts | |||
| Adjustment | DRIVE BELT INSPECTION | ||
| Drive Belt Routing | N/A | ||
| Engine Cooling | |||
| General Service Specifications | TECHNICAL DATA - ENGINE | ||
| Radiator Cap Pressure | 13.6-17.7 psi | ||
| Thermostat R & I | THERMOSTAT REMOVAL/INSTALLATION | ||
| Water Pump R & I | WATER PUMP REMOVAL/INSTALLATION | ||
| Engine Mechanical | |||
| 2.0L 4-Cyl. | |||
| Compression | COMPRESSION INSPECTION | ||
| Oil Pressure | Oil pressure (reference value) [coolant temperature: 80-90 °C {176-194 °F}] Lo: 110-175 kPa {1.13-1.78 kgf/cm2 , 16.0-25.3 psi} [1, 500 rpm] Hi: 300-430 kPa {3.06-4.38 kgf/cm2 , 43.6-62.3 psi} [4, 500 rpm] |
||
| Overhaul | TECHNICAL DATA - ENGINE | ||
| Torque | See Torque Specifications in Text and applicable graphics in ENGINE REMOVAL/INSTALLATION and ENGINE DISASSEMBLY/ASSEMBLY | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | A/T EW6A-EL, EW6AX-EL: 108-116 N.m (80-85 ft. lbs.) | ||
| Fuel System | |||
| Pressure Specification | Skyactive-G 2.0: 425-505 kPa {4.34-5.14 kgf/cm2 , 61.7-73.2 psi} | ||
| Fuel Pressure Test Procedure | FUEL LINE PRESSURE INSPECTION | ||
| Fuel Filter Location And R & I | Fuel Filter is located within the Fuel Pump Unit For replacement see FUEL PUMP UNIT REMOVAL/INSTALLATION and FUEL PUMP UNIT DISASSEMBLY/ASSEMBLY . |
||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil-on-Plug Ignition | ||
| Ignition Wires (Routing) | Coil-on-Plug Ignition | ||
| Spark Plug | |||
| PE5R-18-110, PE5S-18-110 | |||
| Gap | Standard: 1.05-1.40 mm {0.0414-0.0551 in} New spark plug (reference): 1.05-1.15 mm {0.0414-0.0452 in} |
||
| Torque | 15-20 N.m {1.6-2.0 kgf.m, 12-14 ft. lbs.} | ||
| Starting | |||
| Starter | STARTER INSPECTION | ||
| Torque | See Torque Specifications in Text and applicable graphics in STARTER REMOVAL/INSTALLATION |
||
| Wheel Alignment | |||
| Adjustment Specifications | SUSPENSION TECHNICAL DATA | ||
| Torque | See Torque Specifications in Text and applicable graphics in SUSPENSION TECHNICAL DATA and WHEEL ALIGNMENT | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 108-147 N.m {12-14 kgf.m, 80-108 ft.lbf} See Tightening Sequence in illustration under GENERAL PROCEDURES (BRAKE) |
||