Pre-Delivery Inspection

Refer To The Service Information For Detailed Adjustment Procedures

The steps in this inspection sheet are designed for efficient movement around the vehicle.
Problems found during inspection should be noted on a repair order.
Unless otherwise stated, each item should be inspected for fit, appearance and/or operation.
Inspection items followed by an asterisk (*) are required only if the vehicle is equipped with that feature.

Pre-Delivery Inspection Table

General

Check vehicle for any open Recalls, SSPs, or MSPs, and available updates for audio/navigation systems
Install/assemble all loose or packaged parts in the glove box and trunk/cargo area

Exterior

INSPECT and ADJUST, if necessary, the following items to specification:

REMOVE all protective wrap, covers, and window stickers
- Unless the vehicle is scheduled for display or immediate delivery, do not remove the exterior protective film or interior protective covering during inspection
Glass, exterior bright metal and paint for damage
Door and liftgate* operation (Open/Close)
All weather strips for damage or detachment
Security/keyless entry devices (Doors locking/unlocking by transmitter)*
Advanced keyless entry (Doors locking/unlocking by request switches)*
Operation of hood release and lock, trunk release*, and fuel-filler lid opener
Pour one bottle of deposit cleaner into the fuel tank (Specified countries only)
- Refuel the vehicle after adding the deposit cleaner or inform the customer to do so immediately
- For details on the specified countries, please refer to the service information

Under hood-engine off

INSPECT and ADJUST, if necessary, the following items:

INSTALL Fuses for accessories
- ROOM fuse
- AUDIO fuse
Fuel, engine coolant, and hydraulic lines, fittings, connections, and components for leaks
Engine oil level
Brake/clutch fluid level
Windshield washer reservoir fluid level
Radiator coolant level
Tightness of battery terminals, electrolyte level and voltage (12.4 V)
Check the electrolyte specific gravity in case models with i-stop system or i-ELOOP*

Record the voltage and electrolyte specific gravity in the table below.

Judgment Criteria

If the cell with the lowest specific gravity is less than 1.17, replace the battery
If the cell with the lowest specific gravity is 1.17 or more, recharge the battery, after charging if the cell with the lowest specific gravity is less than 1.25, replace the battery.

Please refer to the Service-Information (E039/12A) to get the detail battery inspection procedure.

Record Battery Voltage/Electrolyte specific gravity
Open circuit voltage (V)	V/(after charge V)
Specific Gravity	No. 1	No. 2	No. 3	No. 4	No. 5	No. 6
Before charging
After charging

Interior

INSPECT the operations of the following items:

Secure floor mats to hooks.
Parking brake
Verify that warning lights (check engine, brake, engine oil, charging system, ABS, TPMS) stay on for a few seconds after engine start

Leave Engine Idling In Park Until Reaching Operating Temperature

Horn, front/rear wipers, and washers. Wiper blades performance (Clean wiper blades and windshield, if necessary).
Headlight cleaner (Washer fluid injection)*
Interior and exterior lights, dash switches, headlight leveling switch. (Set position to 0)*
Audio system (Power/Volume/sound controls, Radio, CD player, including steering wheel audio controls)
Heater and A/C (driver, passenger) and front defroster in all mode settings
Turn on navigation system. (Present location indication)*
Adjust clock, dash panel and navigation system*
Power window initialization (if battery was discharged during inventory storage).
Door locks

INSPECT the following items:

Turn Engine Off And raise Vehicle On Lift

ON hoist

INSPECT the following items:

REMOVE under cover
Tires for cuts or bruises
Underside fuel, coolant and hydraulic lines, fittings, connections, and components for leaks
Steering linkage, suspension, exhaust system, and all underside hardware for looseness or damage
INSTALL under cover

Lower Vehicle And Remove From Lift

Tire pressures (See tire label located on driver's side B-pillar or edge driver's of door frame for specification.)
Initialize the TPMS*. Switch the ignition ON, then press and hold TPMS SET switch until the TPMS warning light and one beep flashes twice is heard.
Spare Tire pressures (See tire label located on driver's side B-pillar or edge driver's of door frame for specification.)*
Flat tire repair kit*

Tire pressure record
Left front	Right front	Left rear	Right rear	Spare

Indicated that long-pressing of the tire pressure monitoring system set switch was implemented

Yes or No

Road test-engine running at operating temperature

INSPECT the following items:

After road test

The following items must be completed just before delivery to your customer.

Tire pressures (See tire label located on driver's side B-pillar or edge driver's of door frame for specification.)

Initialize the TPMS*. Switch the ignition ON, then press and hold TPMS SET switch until the TPMS warning light and one beep flashes twice is heard.

NOTE:

Only when the condition TPMS initialization required. Refer to the Service Information.

Tire pressure record
Left front	Right front	Left rear	Right rear	Spare

Indicated that long-pressing of the tire pressure monitoring system set switch was implemented

Yes or No

After washing and drying the vehicle, perform appearance checks before delivery

APPEARANCE CHECKS BEFORE DELIVERY
In addition to function checks, also perform one last inspection of key areas of the vehicle to ensure they are clean and free of chips and scratches.
Check and repair chips and scratches:	Remove dirt and Scratches from key areas:
Door edges Around door handles Door dings and dents Hood leading edges Bumper covers	Door sill scuff plates Door inner panel Seats Carpets and floor mats Steering wheel Center console