| 1 |
VERIFY BCM DTCs
|
Yes |
Repair or replace the malfunctioning part according to the applicable DTC troubleshooting.
(See DTC TABLE [BCM]
.) |
| No |
Go to the next step. |
| 2 |
INSPECT FRONT COMBINATION LIGHT (RH) CONNECTOR CONDITION
- Switch the ignition off.
- Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION
.)
- Disconnect the front combination light (RH) connector.
- Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
- Is the connector normal?
|
Yes |
Go to the next step. |
| No |
Repair or replace the connector, then go to Step 7. |
| 3 |
INSPECT AFS CONTROL MODULE CONNECTOR CONDITION
- Disconnect the AFS control module connector.
- Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
- Is the connector normal?
|
Yes |
Go to the next step. |
| No |
Repair or replace the connector, then go to Step 7. |
| 4 |
INSPECT HEADLIGHT (RH) MALFUNCTION DETECTION CIRCUIT FOR SHORT TO GROUND
- Verify that the front combination light (RH) and AFS control module connectors are disconnected.
- Inspect for continuity between front combination light (RH) terminal N (wiring harness-side) and body ground.
- Is there continuity?
|
Yes |
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
- AFS control module terminal N-Front combination light (RH) terminal N (Without auto leveling sensor)
- AFS control module terminal Z-Front combination light (RH) terminal N (With auto leveling sensor)
If there is a common connector:
- Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.
- Repair or replace the malfunctioning part.
If there is no common connector:
- Repair or replace the wiring harness which has a short to ground.
Go to Step 7. |
| No |
Go to the next step. |
| 5 |
INSPECT HEADLIGHT (RH) MALFUNCTION DETECTION CIRCUIT FOR OPEN CIRCUIT
- Switch the ignition off.
- Verify that the front combination light (RH) and AFS control module connectors are disconnected.
- Inspect for continuity between the following terminals (wiring harness-side):
- AFS control module terminal N-Front combination light (RH) terminal N (Without auto leveling sensor)
- AFS control module terminal Z-Front combination light (RH) terminal N (With auto leveling sensor)
- Is there continuity?
|
Yes |
Go to the next step. |
| No |
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
- AFS control module terminal N-Front combination light (RH) terminal N (Without auto leveling sensor)
- AFS control module terminal Z-Front combination light (RH) terminal N (With auto leveling sensor)
If there is a common connector:
- Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.
- Repair or replace the malfunctioning part.
If there is no common connector:
- Repair or replace the wiring harness which has an open circuit.
Go to Step 7. |
| 6 |
VERIFY IF MALFUNCTIONING LOCATION IS FRONT COMBINATION LIGHT (RH) DEPENDING ON REPEATABILITY
|
Yes |
Replace the front combination light (RH), then go to the next step.
(See FRONT COMBINATION LIGHT REMOVAL/INSTALLATION
.) |
| No |
Go to Step 8. |
| 7 |
VERIFY THAT REPAIRS HAVE BEEN COMPLETED
|
Yes |
Repeat the inspection from Step 1.
Go to the next step. |
| No |
Go to the next step. |
| 8 |
VERIFY IF OTHER DTCs DISPLAYED
- Are any other DTCs displayed?
|
Yes |
Repair or replace the malfunctioning part according to the applicable DTC troubleshooting.
(See DTC TABLE [ADAPTIVE FRONT LIGHTING SYSTEM (AFS) CONTROL MODULE] .) |
| No |
DTC troubleshooting completed. |