LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2021 >> 3 Base >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Drivers Assistance Systems - ADAS >> On-Board Diagnostic - Vehicle Control Module (1 Of 2) >> DTC B14FC-00: Rear Side Radar Sensor (LH) Or (RH) Internal Temperature Abnormality [Vehicle Control Module] >> Diagnostic Procedure

Diagnostic Procedure

DTC B14FC:00 [VEHICLE CONTROL MODULE] DIAGNOSTIC PROCEDURE

Step Inspection Results Action
1 INSPECT VEHICLE CONTROL MODULE (VCM) AND BODY CONTROL MODULE (BCM) FOR MALFUNCTION
  • Perform the DTC inspection for the vehicle control module (VCM) and the body control module (BCM). (See DTC INSPECTION .)
  • Is a DTC related to an internal malfunction displayed?
 Yes Repair the malfunctioning location according to the applicable DTC troubleshooting.
(See DTC TABLE [VEHICLE CONTROL MODULE (US)] .)
(See DTC TABLE [BODY CONTROL MODULE (BCM) (US)] .)
No Go to the next step.
2 INSPECT REAR SIDE RADAR SENSOR (LH) FOR MALFUNCTION
  • Perform the DTC inspection for the rear side radar sensor (LH). (See DTC INSPECTION .)
  • Is a DTC displayed?
 Yes Repair the malfunctioning location according to the applicable DTC troubleshooting.
(See DTC TABLE [REAR SIDE RADAR SENSOR (US)] .)
No Go to the next step.
3 INSPECT REAR SIDE RADAR SENSOR (RH) FOR MALFUNCTION
  • Perform the DTC inspection for the rear side radar sensor (RH). (See DTC INSPECTION .)
  • Is a DTC displayed?
 Yes Repair the malfunctioning location according to the applicable DTC troubleshooting.
(See DTC TABLE [REAR SIDE RADAR SENSOR (US)] .)
No Go to the next step.
4 VERIFY IF REAR SIDE RADAR SENSOR FUNCTION IS STOPPED DUE TO TEMPORARY DECREASE IN INTERNAL TEMPERATURE
  • Start the engine and move the vehicle to a warm place.
  • Clear the DTC recorded in the memory. (See CLEARING DTC .)
  • Perform the DTC inspection for the vehicle control module (VCM). (See DTC INSPECTION .)
  • Is the same Pending DTC present?
 Yes Go to the next step.
No Explain to the customer that the rear side radar sensor function stopped due to a temporary decrease in the internal temperature of the rear side radar sensor, and then go to repair completion verification 2.
5 DETERMINE IF MALFUNCTION CAUSE IS REAR SIDE RADAR SENSOR ON EITHER LEFT OR RIGHT
  • Install/connect the part removed/disconnected during the troubleshooting procedure.
  • Disconnect the rear side radar sensor (RH) connector.
  • Clear the DTC recorded in the memory. (See CLEARING DTC .)
  • Perform the DTC inspection for the vehicle control module (VCM). (See DTC INSPECTION .)
  • Is the same Pending DTC present?
 Yes Replace the rear side radar sensor (LH), then go to the next step.
(See REAR SIDE RADAR SENSOR REMOVAL/INSTALLATION .)
No Replace the rear side radar sensor (RH) and perform the repair completion verification.
(See REAR SIDE RADAR SENSOR REMOVAL/INSTALLATION .)
6 INSPECT REAR SIDE RADAR SENSOR (RH) FOR MALFUNCTION DEPENDING ON REPEATABILITY
  • Install/connect the part removed/disconnected during the troubleshooting procedure.
  • Clear the DTC recorded in the memory. (See CLEARING DTC .)
  • Perform the DTC inspection for the vehicle control module (VCM). (See DTC INSPECTION .)
  • Is the same Pending DTC present?
 Yes Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW (US) .)
If the CAN communication is normal, replace the rear side radar sensor (RH) and perform the repair completion verification.
(See REAR SIDE RADAR SENSOR REMOVAL/INSTALLATION .)
No Go to repair completion verification 2.
Repair completion verification 1 VERIFY THAT VEHICLE IS REPAIRED
  • Install/connect the part removed/disconnected during the troubleshooting procedure.
  • Clear the DTC recorded in the memory. (See CLEARING DTC .)
  • Perform the DTC inspection for the vehicle control module (VCM). (See DTC INSPECTION .)
  • Is the same Pending DTC present?
 Yes Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW (US) .)
If the CAN communication is normal, perform the diagnosis from Step 1.
No Go to the next step.
Repair completion verification 2 VERIFY IF OTHER DTC IS DISPLAYED
  • Perform the DTC inspection. (See DTC INSPECTION .)
  • Are any other DTCs displayed?
 Yes Repair the malfunctioning location according to the applicable DTC troubleshooting.
No DTC troubleshooting completed.
scientia non olet · About LEMON Manuals