LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2017 >> CX-5 Grand Select, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 38 (On-Board Diagnostic [Front Body Control Module (FBCM)]) >> PID/Data Monitor Table [Front Body Control Module (FBCM)]

PID/Data Monitor Table [Front Body Control Module (FBCM)]

WARNING: This page is about a different car, the 2016 Mazda CX-5. However, it is still accessible from the selected car via links, so may be relevant.

-: Not applicable

PID Unit/Operation Data contents Data read/use method Inspection item(s)
ABK_CS_BG Off/On
  • Off: Theft-deterrent system answer-back signal is not received.
  • On: Theft-deterrent system answer-back signal is received.
 -
  • Front body control module (FBCM)
  • Rear body control module (RBCM)
  • Start stop unit
ABK_CS_KEY(1) Off/On
  • Off: Advanced keyless entry system answer-back signal is not received.
  • On: Advanced keyless entry system answer-back signal is received.
 -
  • Front body control module (FBCM)
  • Rear body control module (RBCM)
  • Start stop unit
ABK_HD_CS_R
NOTE:
  • If an accessory part is installed, it cannot be used.
ABK_HN_CS_R
NOTE:
  • If an accessory part is installed, it cannot be used.
ABK_HN_KEY(1) Off/On
  • Off: Keyless entry system horn answer-back signal is not received.
  • On: Keyless entry system horn answer-back signal is received.
 -
  • Front body control module (FBCM)
  • Rear body control module (RBCM)
  • Start stop unit
BAT_TMP °C, °F Displays battery temperature - Battery
BG_ALARM_CS(2) Off/On
  • Off: Theft-deterrent system alarm signal is not received.
  • On: Theft-deterrent system alarm signal is received.
 -
  • Front body control module (FBCM)
  • Rear body control module (RBCM)
BLWR_MT_RY Off/On
  • Off: Blower relay is off.
  • On: Blower relay is on.
 - Blower relay
BRAKE_SW Off/On
  • Off: Brake switch (No. 2) is off (brake pedal is depressed).
  • On: Brake switch (No. 2) is on (brake pedal is not depressed).
 -
  • Brake switch
  • PCM
  • TCM
BRK_F_L_SW Normal/Low/Reserved/Unknown
  • Normal: Brake fluid level is between MAX and MIN.
  • Low: Brake fluid level is lower than MIN.
  • Reserved: -
  • Unknown: Brake fluid level is not determined.
 - Brake fluid level sensor
DCDC_CVT_ST
NOTE:
  • Displays in the M-MDS but it does not operate.
DCDC_VLT_I
NOTE:
  • Displays in the M-MDS but it does not operate.
DCDC_VLT_O
NOTE:
  • Displays in the M-MDS but it does not operate.
DEFOG_F_CS
NOTE:
  • Displays in the M-MDS but it does not operate.
DEFOG_R_CS Off/On
  • Off: Rear window defogger control signal is not received.
  • On: Rear window defogger control signal is received.
 -
  • Front body control module (FBCM)
  • Climate control unit
ENG_C_TMP °C, °F Displays engine coolant temperature -
  • ECT sensor
  • PCM
ESS_ST Off/On
  • Off: ESS is not operated.
  • On: ESS is operated.
 -
  • Front body control module (FBCM)
  • DSC HU/CM
F_FOG_LMP(3) Off/On
  • Off: Front fog light is turned off.
  • On: Front fog light is turned on.
 - Front fog light
F_FOG_SW(3) Off/On
  • Off: Front fog light switch is not in F.FOG position
  • On: Front fog light switch is in F.FOG position
 -
  • Front fog light switch
  • Start stop unit
H/L OFF/DRL/TNS/H/L_LOW/H/L_HI
  • OFF: Headlight is turned off.
  • DRL: DRL (Daytime running light) is turned on.
  • TNS: TNS is turned on.
  • H/L_LOW: Headlight (LO) is turned on.
  • H/L_HI: Headlight (HI) is turned on.
 -
  • Headlight relay (HI/LO)
  • Parking light
  • Taillight
  • License plate light
  • DRL (Daytime running light)
H/L_CLN_RLY
NOTE:
  • Displays in the M-MDS but it does not operate.
H/L_CS_RLS Off/TNS_On/TNS+H/L_On
  • Off: TNS and headlight on request signal is not received from auto-light sensor.
  • TNS_On: TNS on signal is received from auto-light sensor.
  • TNS+H/L_On: TNS and headlight LO on signal is received from auto-light sensor.
 - Auto-light sensor
H/L_HI Off/On
  • Off: Headlight HI is turned off.
  • On: Headlight HI is turned on.
 - Headlight HI
H/L_SW_HI Off/On
  • Off: Light switch is in LO position.
  • On: Light switch is in HI position.
 -
  • Light switch
  • Start stop unit
H/L_SW_LOW1 Off/On Displays dimmer switch position of light switch sent from start stop unit via CAN signal
  • Off: Other than dimmer switch LO position of light switch is received
  • On: Dimmer switch LO position of light switch is received
 Verify if the monitor value switches when the dimmer switch of the light switch is switched between LO and HI positions. If the dimmer switch operation and monitor values do not match, inspect the start stop unit or CAN communication.
  • Light switch
  • Start stop unit
H/L_SW_OFF Off/On
  • Off: Light switch is not in OFF position
  • On: Light switch is in OFF position
 -
  • Light switch
  • Start stop unit
H/L_SW_PASS Off/On
  • Off: Light switch is not in passing position
  • On: Light switch is in passing position
 -
  • Light switch
  • Start stop unit
H/L_SW_TNS Off/On
  • Off: Light switch is not in TNS position
  • On: Light switch in TNS position
 -
  • Light switch
  • Start stop unit
H/L_TNS Off/On
  • Off: TNS is turned off.
  • On: TNS is turned on.
 -
  • Parking light
  • Taillight
  • License plate lights
HAZARD_LMP Off/On
  • Off: Hazard light is turned off.
  • On: Hazard light is turned on.
 -
  • Front turn light
  • Side turn lights
  • Rear turn light
HAZARD_SW Off/On/Unknown
  • Off: Hazard warning switch is not pressed.
  • On: Hazard warning switch is pressed.
  • Unknown: Hazard warning switch on/off is not determined.
 -
  • Hazard warning switch
  • Start stop unit
HBC_CS
NOTE:
  • Displays in the M-MDS but it does not operate.
HBC_ST
NOTE:
  • Displays in the M-MDS but it does not operate.
HEAT_CS_R
NOTE:
  • Displays in the M-MDS but it does not operate.
IG_ST Off/On
  • Off: IG1 is off.
  • On: IG1 is on.
 -
  • IG1 relay
  • PCM
  • Start stop unit
L_OFF_AUTO Off/On
  • Off: TNS or headlight off control by auto-light off system is not operated.
  • On: TNS or headlight off control by auto-light off system is operated.
 -
  • Front body control module (FBCM)
  • Auto light sensor
L_OFF_BS
NOTE:
  • Displays in the M-MDS but it does not operate.
OIL_P_SW
NOTE:
  • Displays in the M-MDS but it does not operate.
OUT_CAR_TMP °C, °F Ambient temperature is displayed. -
  • Ambient temperature sensor
  • PCM
P_BRAKE_SW Off/On
  • Off: Parking brake switch is off (parking brake lever is not pulled).
  • On: Parking brake switch is on (parking brake lever is pulled).
 -
  • Parking brake switch
  • Instrument cluster
PNC_CS Off/On
  • Off: Panic control signal is not received.
  • On: Panic control signal is received.
 -
  • Front body control module (FBCM)
  • Rear body control module (RBCM)
PNC_HD_CS_R
NOTE:
  • If an accessory part is installed, it cannot be used.
PNC_HN_CS_R
NOTE:
  • If an accessory part is installed, it cannot be used.
PTC_HEAT_CS
NOTE:
  • Displays in the M-MDS but it does not operate.
R_FOG_LMP
NOTE:
  • Displays in the M-MDS but it does not operate.
R_FOG_SW
NOTE:
  • Displays in the M-MDS but it does not operate.
RES_CS
NOTE:
  • If an accessory part is installed, it cannot be used.
RLS_FLT(4) O.K./FAULT
  • OK: Rain sensor is normal.
  • FAULT: Rain sensor has a malfunction.
 - Rain sensor
S_HT_CUT(5) No_Request/Cut
NOTE:
  • The FBCM controls the seat warmer output at an appropriate timing in consideration of the vehicle conditions such as power supply voltage decrease.
  • No_Request: Except below
  • Cut: When FBCM stops or lowers seat warmer output
 - Front body control module (FBCM)
SHIFT_L_POS(6) Between/P/R/N/D/S(2)//L(1)
  • Between: Selector lever receives signal between two positions.
  • P: Selector lever receives P position signal.
  • R: Selector lever receives R position signal.
  • N: Selector lever receives N position signal.
  • D: Selector lever receives D position signal.
  • S (2): Selector lever receives D position 2nd gear signal.
  • L (1): Selector lever receives D position 1st gear signal.
 - TCM
TURN_L_L Off/On
  • Off: Turn light (LH) is turned off.
  • On: Turn light (LH) is turned on.
 -
  • Front turn light
  • Side turn lights
  • Rear turn light
TURN_L_R Off/On
  • Off: Turn light (RH) is turned off.
  • On: Turn light (RH) is turned on.
 -
  • Front turn light
  • Side turn lights
  • Rear turn light
TURN_SW Off/Turn_R_On/Turn_L_On/Unknown
  • Off: Turn switch receives OFF signal.
  • Turn_R_On: Turn switch receives RH signal.
  • Turn_L_On: Turn switch receives LH signal.
  • Unknown: Turn switch receives signal not determined.
 -
  • Turn Switch
  • Start stop unit
VPWR_B V Front body control module (FBCM) power supply voltage is displayed. - Front body control module (FBCM)
VSPD KPH, MPH Vehicle speed is displayed. - PCM
WAS_FLUID_L(7) Normal/Low/Reserved/Unknown
  • Normal: Washer fluid level is normal.
  • Low: Washer fluid level is low.
  • Reserved: -
  • Unknown: Washer fluid level is not determined.
 - Washer fluid-level sensor
WAS_MT_RY_F Off/On
  • Off: Front washer motor relay is off.
  • On: Front washer motor relay is on.
 - Front body control module (FBCM)
WAS_MT_RY_R Off/On
  • Off: Rear washer motor relay is off.
  • On: Rear washer motor relay is on.
 - Front body control module (FBCM)
WASHER_F Off/On
  • Off: Front washer receives OFF signal.
  • On: Front washer receives ON signal.
 -
  • Windshield washer switch
  • Start stop unit
WASHER_R Off/On
  • Off: Rear wiper and washer switch receives OFF signal of rear washe.
  • On: Rear wiper and washer switch receives ON signal of rear washer.
 -
  • Rear wiper and washer switch
  • Start stop unit
WIP_CS_RLS(4) Off/Single_Wipe/F_Wiper_LOW/F_Wiper_HI/Failure
  • Off: Wiper operation signal is not received from rain sensor.
  • Single_Wipe: Signal to operate wiper once is received from rain sensor.
  • F_Wiper_LOW: Signal to operate wiper at low speed is received from rain sensor.
  • F_Wiper_HI: Signal to operate wiper at high speed is received from rain sensor.
  • Failure: Communication with rain sensor is failed.
 - Rain sensor
WIP_F OFF/LOW/HI/INT/AUTO
  • OFF: Windshield wiper switch receives OFF signal.
  • LOW: Windshield wiper switch ireceives LO signal.
  • HI: Windshield wiper switch receives HI signal.
  • INT/AUTO: Windshield wiper switch receives INT or AUTO signal.
 -
  • Windshield wiper switch
  • Start stop unit
WIP_F_INT_L % Windshield wiper INT level signal value received. -
  • Windshield wiper switch
  • Start stop unit
WIP_F_LOW Off/On
  • Off: Windshield wiper switch is not in LO position.
  • On: Windshield wiper switch is in LO position.
 -
  • Windshield wiper switch
  • Start stop unit
WIP_F_MST Stop/Move
  • Stop: Autostop switch is on.
  • Move: Autostop switch is off.
 - Windshield wiper motor
WIP_F_RY_HI Off/On
  • Off: Windshield wiper high relay is off.
  • On: Windshield wiper high relay is on.
 - Front body control module (FBCM)
WIP_F_RY_LO Off/On
  • Off: Windshield wiper low relay is off.
  • On: Windshield wiper low relay is on.
 - Front body control module (FBCM)
WIP_R OFF/LOW/INT
  • OFF: Rear wiper switch receives OFF signal.
  • LOW: Rear wiper switch receives ON signal.
  • INT: Rear wiper switch receive INT signal.
 -
  • Rear wiper switch
  • Start stop unit
WIP_R_RY Off/On
  • Off: Rear wiper motor is not operated.
  • On: Rear wiper motor is operated.
 -
  • Rear wiper motor
  • Instrument cluster
  • Rear body control module (RBCM)
(1) Vehicles with advanced keyless entry system
(2) With theft-deterrent system
(3) With front fog lights
(4) With auto-light sensor
(5) With seat warmer
(6) ATX
(7) With washer fluid-level sensor
scientia non olet · About LEMON Manuals