LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2017 >> 6 Touring, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 29 (On-Board Diagnostic - Front Body Control Module) >> PID/Data Monitor Table

PID/Data Monitor Table

WARNING: This page is about a different car, the 2014 Mazda 6. However, it is still accessible from the selected car via links, so may be relevant.
PID/DATA MONITOR ITEM DESCRIPTION (FRONT BODY CONTROL MODULE)

-: Not applicable
PID Unit/Operation Data contents Data read/use method Inspection item(s)
ABK_CS_BG(1) Off/On
  • Off: Theft-deterrent system answer-back signal is not received.
  • On: Theft-deterrent system answer-back signal is received.
 -
  • Front body control module (FBCM)
  • Rear body control module (RBCM)
  • Start stop unit
ABK_CS_KEY Off/On
  • Off: Keyless entry system answer-back signal is not received.
  • On: Keyless entry system answer-back signal is received.
 -
  • Front body control module (FBCM)
  • Rear body control module (RBCM)
  • Start stop unit
ABK_HD_CS_R Off/On
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
 - -
ABK_HN_CS_R Off/On
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
 - -
ABK_HN_KEY Off/On
  • Off: Keyless entry system horn answerback signal is not received.
  • On: Keyless entry system horn answerback signal is received.
 -
  • Front body control module (FBCM)
  • Rear body control module (RBCM)
  • Start stop unit
BAT_TMP °C, °F Displays battery temperature - Battery
BG_ALARM_CS(1) Off/On
  • Off: Hazard warning light flashing request siganal is not received
  • On: Hazard warning light flashing request siganal is received
 -
  • Front body control module (FBCM)
  • Rear body control module (RBCM)
BLWR_MT_RY Off/On
  • Off: Blower relay is off.
  • On: Blower relay is on.
 - Blower relay
BRAKE_SW Off/On
  • Off: Brake switch (No. 2 signal) is off. (Brake pedal is depressed.)
  • On: Brake switch (No. 2 signal) is on. (Brake pedal is not depressed.)
 -
  • Brake switch
  • PCM
  • TCM
BRK_F_L_SW Normal/Low/Unknown
  • Normal: Brake fluid level is between MAX and MIN.
  • Low: Brake fluid level is lower than MIN.
  • Unknown: Brake fluid level is not determined.
 - Brake fluid level sensor
DCDC_CVT_ST
NOTE:
  • Displays in the M-MDS but it does not operate.
DCDC_VLT_I
NOTE:
  • Displays in the M-MDS but it does not operate.
DCDC_VLT_O
NOTE:
  • Displays in the M-MDS but it does not operate.
DEFOG_F_CS
NOTE:
  • Displays in the M-MDS but it does not operate.
DEFOG_R_CS Off/On
  • Off: Rear window defroster control signal is not received.
  • On: Rear window defroster control signal is received.
 -
  • Front body control module (FBCM)
  • Climate control unit
ENG_C_TM P °C, °F Displays engine coolant temperature -
  • ECT sensor
  • PCM
ESS_ST
NOTE:
  • Displays in the M-MDS but it does not operate.
F_FOG_LM P(2) Off/On
  • Off: Front fog light is turned off.
  • On: Front fog light is turned on.
 - Front fog light
F_FOG_SW(2) Off/On
  • Off: Front fog light switch F.FOG signal is not received.
  • On: Front fog light switch F.FOG signal is received.
 -
  • Front fog light switch
  • Start stop unit
H/L OFF/DRL/TNS/H/L_LOW/H/L_HI/
  • OFF: Headlight is turned off.
  • DRL: DRL is turned on.
  • TNS: TNS is turned on.
  • H/L_LOW: Headlight (LO) is turned on.
  • H/L_HI: Headlight (HI) is turned on.
 -
  • Headlight relay (HI)/(LO)
  • Parking light
  • Taillight
  • License plate light
  • DRL
H/L_CLN_RY
NOTE:
  • Displays in the M-MDS but it does not operate.
H/L_CS_RLS(3) Off/TNS_On/TNS+H/L_On
  • Off: TNS and headlight on request signal is not received from auto light sensor.
  • TNS_On: TNS on signal is received from auto light sensor.
  • TNS+H/L_On: TNS and headlight LO on signal is received from auto light sensor.
 - Auto light sensor
H/L_HI Off/On
  • Off: Headlight HI is turned off.
  • On: Headlight HI is turned on.
 - Headlight HI
H/L_SW_HI Off/On
  • Off: Light switch HI signal is not received.
  • On: Light switch HI signal is received.
 -
  • Light switch
  • Start stop unit
H/L_SW_LOW 1 Off/On Displays dimmer switch position of light switch sent from start stop unit via CAN signal
  • Off: Other than dimmer switch LO position of light switch is received
  • On: Dimmer switch LO position of light switch is received
 Verify if the monitor value switches when the dimmer switch of the light switch is switched between LO and HI positions. If the dimmer switch operation and monitor values do not match, inspect the start stop unit or CAN communication.
NOTE:
  • If PID items H/L_SW_LOW1 and H/L_SW_LOW2 do not match, the front body control module (FBCM) detects a DTC. Also, the headlight (low) may be constantly illuminated.
  • Light switch
  • Start stop unit
H/L_SW_LOW 2 Off/On Displays dimmer switch position of light switch connected to front body control module (FBCM) terminal 2W
  • Off: Other than dimmer switch LO position of light switch is received
  • On: Dimmer switch LO position of light switch is received
 Verify if the monitor value switches when the dimmer switch of the light switch is switched between LO and HI positions. If the dimmer switch operation and monitor values do not match, inspect the light switch or related wiring harness.
NOTE:
  • If PID items H/L_SW_LOW1 and H/L_SW_LOW2 do not match, the front body control module (FBCM) detects a DTC. Also, the headlight (low) may be constantly illuminated.
  • Light switch
  • Start stop unit
H/L_SW_OFF Off/On
  • Off: Light switch OFF signal is not received.
  • On: Light switch OFF signal is received.
 -
  • Light switch
  • Start stop unit
H/L_SW_PAS S Off/On
  • Off: Light switch FLASH-TO-PASS signal is not received.
  • On: Light switch FLASH-TO-PASS signal is received.
 -
  • Light switch
  • Start stop unit
H/L_SW_TNS Off/On
  • Off: Light switch TNS signal is not received.
  • On: Light switch TNS signal is received.
 -
  • Light switch
  • Start stop unit
H/L_TNS Off/On
  • Off: TNS is turned off.
  • On: TNS is turned on.
 -
  • Parking light
  • Taillight
  • License plate light
HAZARD_L MP Off/On
  • Off: Hazard light is turned off.
  • On: Hazard light is turned on.
 -
  • Front turn light
  • Side turn light
  • Rear turn light
HAZARD_S W Off/On/Unknown
  • Off: Hazard warning switch is not pressed.
  • On: Hazard warning switch is pressed.
  • Unknown: Hazard warning switch on/off is not determined.
 -
  • Hazard warning switch
  • Start stop unit
HBC_CS(4) Off/On/Invalid
  • Off: High beam control (HBC) system signal is not received.
  • On: High beam control (HBC) system signal is received.
  • Invalid: High beam control (HBC) system signal has error.
 - Forward sensing camera (FSC)
HBC_ST(4) Off/On
  • Off: High beam control (HBC) system is not operated.
  • On: High beam control (HBC) system is operated.
 - Forward sensing camera (FSC)
HEAT_CS_R
NOTE:
  • Displays in the M-MDS but it does not operate.
IG_ST Off/On
  • Off: IG1 is off.
  • On: IG1 is on.
 -
  • IG1 relay
  • PCM
  • Start stop unit
L_OFF_AUT O Off/On
  • Off: TNS or headlight off control by auto light off system is not operated.
  • On: TNS or headlight off control by auto light off system is operated.
 -
  • Front body control module (FBCM)
  • Auto light sensor
L_OFF_BS
NOTE:
  • Displays in the M-MDS but it does not operate.
OIL_P_SW
NOTE:
  • Displays in the M-MDS but it does not operate.
OUT_CAR_TMP °C, °F Displays ambient temperature -
  • Ambient temperature sensor
  • PCM
P_BRAKE_SW Off/On
  • Off: Parking brake switch is off. (Parking brake lever is not pulled.)
  • On: Parking brake switch is on. (Parking brake lever is pulled.)
 -
  • Parking brake switch
  • Instrument cluster
PNC_CS Off/On
  • Off: Panic control signal is not received.
  • On: Panic control signal is received.
 -
  • Front body control module (FBCM)
  • Rear body control module (RBCM)
PNC_HD_CS_R Off/On
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
 - -
PNC_HN_CS_R Off/On
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
 - -
PTC_HEAT_CS
NOTE:
  • Displays in the M-MDS but it does not operate.
R_FOG_LMP
NOTE:
  • Displays in the M-MDS but it does not operate.
R_FOG_SW
NOTE:
  • Displays in the M-MDS but it does not operate.
RES_CS Off/On
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
 - -
RLS_FLT(3) O.K./FAULT
  • OK: Rain sensor is normal.
  • FAULT: Rain sensor has a malfunction.
 - Rain sensor
S_HT_CUT(5) No_Request/Cut
  • No_Request: Except below
  • Cut: Seat warmer is turned off or lowered.
 - Front body control module (FBCM)
SHIFT_L_P OS(6) Between/P/R/N/D/S(2)/L(1)
  • Between: Selector lever is between two positions.
  • P: Selector lever is in P position.
  • R: Selector lever is in R position.
  • N: Selector lever is in N position.
  • D: Selector lever is in D position.
  • S(2): Selector lever is in D position 2nd gear.
  • L(1): Selector lever is in D position 1st gear.
 - TCM
TURN_L_L Off/On
  • Off: Turn light (LH) is turned off.
  • On: Turn light (LH) is turned on.
 -
  • Front turn light
  • Side turn light
  • Rear turn light
TURN_L_R Off/On
  • Off: Turn light (RH) is turned off.
  • On: Turn light (RH) is turned on.
 -
  • Front turn light
  • Side turn light
  • Rear turn light
TURN_SW Off/Turn_R_On/Turn_L_On/Unknown
  • Off: Turn switch is in OFF position.
  • Turn_R_On: Turn switch is in RH position.
  • Turn_L_On: Turn switch is in LH position.
  • Unknown: Turn switch position is not determined.
 -
  • Turn Switch
  • Start stop unit
VPWR_B V Displays front body control module (FBCM) power supply voltage - Front body control module (FBCM)
VSPD KPH, MPH Displays vehicle speed - PCM
WAS_FLUID_L Normal/Low/Unknown
  • Normal: Washer fluid level is normal.
  • Low: Washer fluid level is low.
  • Unknown: Washer fluid level is not determined.
 - Washer fluid-level sensor
WAS_MT_RY_F Off/On
  • Off: Windshield washer motor relay is off.
  • On: Windshield washer motor relay is on.
 - Front body control module (FBCM)
WAS_MT_RY_R
NOTE:
  • Displays in the M-MDS but it does not operate.
WASHER_F Off/On
  • Off: Windshield washer switch is off.
  • On: Windshield washer switch is on.
 -
  • Windshield washer switch
  • Start stop unit
WASHER_R
NOTE:
  • Displays in the M-MDS but it does not operate.
WIP_CS_R LS(3) Off/Single_Wipe/F_Wiper_LOW/F_Wiper_HI/Failure
  • Off: Wiper operation signal is not received from rain sensor.
  • Single_Wipe: Signal to operate wiper once is received from rain sensor.
  • F_Wiper_LOW: Signal to operate wiper at low speed is received from rain sensor.
  • F_Wiper_HI: Signal to operate wiper at high speed is received from rain sensor.
  • Failure: Communication with rain sensor is failed.
 - Rain sensor
WIP_F OFF/LOW/HI/INT/AUTO
  • OFF: Windshield wiper switch is in OFF position.
  • LOW: Windshield wiper switch is in LO position.
  • HI: Windshield wiper switch is in HI position.
  • INT/AUTO: Windshield wiper switch is in INT or AUTO position.
 -
  • Windshield wiper switch
  • Start stop unit
WIP_F_INT_L % Displays windshield wiper INT level signal value received -
  • Windshield wiper switch
  • Start stop unit
WIP_F_LO W Off/On
  • Off: Windshield wiper switch is not in LO position.
  • On: Windshield wiper switch is in LO position.
 -
  • Windshield wiper switch
  • Start stop unit
WIP_F_MS T Stop/Move
  • Stop: Autostop switch is on.
  • Move: Autostop switch is off.
 - Windshield wiper motor
WIP_F_RY_HI Off/On
  • Off: Windshield wiper HI relay is off.
  • On: Windshield wiper HI relay is on.
 - Front body control module (FBCM)
WIP_F_RY_LO Off/On
  • Off: Windshield wiper LO relay is off.
  • On: Windshield wiper LO relay is on.
 - Front body control module (FBCM)
WIP_R
NOTE:
  • Displays in the M-MDS but it does not operate.
WIP_R_RY
NOTE:
  • Displays in the M-MDS but it does not operate.
(1) With theft-deterrent system
(2) With front fog light
(3) With auto light sensor/rain sensor
(4) With high beam control (HBC) system
(5) With seat warmer
(6) ATX
scientia non olet · About LEMON Manuals