LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2017 >> 3 Sport, 4D Hatchback, Standard Trans >> Repair and Diagnosis >> Electrical >> Body Electrical >> Power Systems >> Relay And Fuse Block Removal/Installation >> Removal

Relay And Fuse Block Removal/Installation: Removal

  1. Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .)
  2. Remove the air cleaner case. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .)
  3. Remove the battery tray. (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .)
  4. While pressing the relay and fuse block upper cover hook in the direction of the arrow (1) shown in the figure, lift up the relay and fuse block upper cover in the direction of the arrow (2) to detach the relay and fuse block upper cover hook from the relay and fuse block middle cover tab.
    Fig 1: Detaching Relay And Fuse Block Upper Cover Hook From Relay And Fuse Block Middle Cover Tab
    G11467421Courtesy of MAZDA MOTORS CORP.
  5. Remove the relay and fuse block upper cover.
  6. Remove the front body control module (FBCM). (See FRONT BODY CONTROL MODULE (FBCM) REMOVAL/INSTALLATION .)
  7. Remove the multiplex slow blow fuse. (See MULTIPLEX SLOW BLOW FUSE REMOVAL/INSTALLATION .)
  8. Remove all the relays and fuses.
    CAUTION:
    • If the relay and fuse block is removed with the relays and fuses installed, the area around the relay and fuse block may contact the relays or fuses and damage the them. Before removing the relay and fuse block, remove all the relays and fuses.
  9. While pressing the relay and fuse block hook in the direction of the arrow (1) shown in the figure, set the emission wiring harness away in the direction of the arrow (2) shown in the figure from the relay and fuse block hook.
    Fig 2: Pressing Relay And Fuse Block Hook
    G11467422Courtesy of MAZDA MOTORS CORP.
  10. Disconnect the emission wiring harness connectors.
    Fig 3: Emission Wiring Harness Connector
    G11467423Courtesy of MAZDA MOTORS CORP.
  11. Remove the nut and bolt.
    Fig 4: Removing Relay And Fuse Block Nut And Bolt
    G11467424Courtesy of MAZDA MOTORS CORP.
  12. Pull out the relay and fuse block from the stud bolt and set it aside as shown in the figure.
    Fig 5: Pulling Out Relay And Fuse Block From Stud Bolt
    G11467425Courtesy of MAZDA MOTORS CORP.
  13. While pressing the clip tabs of front wiring harness protector No. 2 in the direction of the arrows (1) shown in the figure, pull the clip of front wiring harness protector No. 2 in the direction of the arrow (2) shown in the figure to detach the clip tabs of front wiring harness protector No. 2 from the engine mount.
    Fig 6: Pressing Clip Tabs Of Front Wiring Harness Protector
    G11467426Courtesy of MAZDA MOTORS CORP.
  14. Pull out the front wiring harness protector No. 2 clip.
  15. Lift up the front wiring harness protector No. 2 cap in the direction of the arrow shown in the figure.
    Fig 7: Lifting Up Front Wiring Harness Protector Cap
    G11467427Courtesy of MAZDA MOTORS CORP.
  16. Pull out the front wiring harness protector No. 2 from the stud bolt and set it aside as shown in the figure.
    Fig 8: Pulling Out Front Wiring Harness Protector From Stud Bolt
    G09788460Courtesy of MAZDA MOTORS CORP.
  17. Cut the bands shown in the figure.
    Fig 9: Relay And Fuse Block Band
    G11467429Courtesy of MAZDA MOTORS CORP.
  18. Insert a flathead screwdriver into the gap between the relay and fuse block middle cover tabs and the relay and fuse block lower cover as shown in the figure.
    Fig 10: Inserting Flathead Screwdriver Into Gap Between Relay And Fuse Block Middle Cover Tabs
    G11467430Courtesy of MAZDA MOTORS CORP.
  19. Move the flathead screwdriver in the direction of the arrow (1) shown in the figure, and pull down the relay and fuse block lower cover in the direction of the arrow (2) shown in the figure to detach the relay and fuse block middle cover tab from the relay and fuse block lower cover.
    Fig 11: Detaching Relay And Fuse Block Middle Cover Tab From Relay And Fuse Block Lower Cover
    G11467431Courtesy of MAZDA MOTORS CORP.
  20. Detach all of the relay and fuse block middle cover and the relay and fuse block lower cover.
  21. While pressing the wiring harness clip tabs in the direction of the arrows (1) shown in the figure, push out the wiring harness clip in the direction of the arrow (2) shown in the figure to detach the wiring harness clip tabs from the relay and fuse block lower cover.
    Fig 12: Detaching Wiring Harness Clip Tabs From Relay And Fuse Block Lower Cover
    G11467432Courtesy of MAZDA MOTORS CORP.
  22. Pull out the wiring harness clip.
  23. Remove the relay and fuse block lower cover.
  24. Insert a flathead screwdriver into the service hole in the position shown in the figure.
    Fig 13: Inserting Flathead Screwdriver Into Service Hole
    G11467433Courtesy of MAZDA MOTORS CORP.
  25. Move the flathead screwdriver in the direction of the arrow (1) shown in the figure, and lift up the front wiring harness connector in the direction of the arrow (2) shown in the figure to detach the front wiring harness connector tab from the relay and fuse block middle cover.
    Fig 14: Detaching Front Wiring Harness Connector Tab From Relay And Fuse Block Middle Cover
    G11467434Courtesy of MAZDA MOTORS CORP.
  26. Move the front wiring harness connector in the direction of the arrow shown in the figure, release the hook, and pull it out from the relay and fuse block middle cover.
    Fig 15: Removing Front Wiring Harness Connector
    G11467435Courtesy of MAZDA MOTORS CORP.
  27. Pull out all the front wiring harness connectors from the relay and fuse block middle cover.
  28. Insert the flathead screwdriver into the gap between the relay and fuse block middle cover and the relay and fuse block shown in the figure.
    Fig 16: Relay And Fuse Block Middle Cover Flathead Screwdriver Insertion Holes
    G11467436Courtesy of MAZDA MOTORS CORP.
  29. Move the flathead screwdriver in the direction of the arrow (1) shown in the figure, and pull up the relay and fuse block middle cover in the direction of the arrow (2) shown in the figure to detach the relay and fuse block tab from the relay and fuse block middle cover.
    Fig 17: Detaching Relay And Fuse Block Tab From Relay And Fuse Block Middle Cover
    G11467437Courtesy of MAZDA MOTORS CORP.
  30. Detach all the relay and fuse block tabs from the relay and fuse block middle cover, and remove the relay and fuse block middle cover.
  31. Set the removed relay and fuse block aside so that it does not scratch the vehicle and parts.
scientia non olet · About LEMON Manuals