Diagnostic procedure

Step	Inspection		Action
1	BATTERY INSPECTION Refer to the battery inspection and inspect the battery. (Refer to BATTERY INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Is the battery normal?	Yes	Go to the next step.
1		No	Replace or charge the battery. (Refer to BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) (Refer to BATTERY RECHARGING [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Then go to Step 5.
2	FUSE INSPECTION Switch the ignition off. Disconnect the negative battery cable and wait 1 min or more . (Refer to NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Remove the SRS1 7.5 A fuse. Is the fuse normal?	Yes	Go to the next step.
2		No	Replace the SRS1 7.5 A fuse. Then go to Step 5.
3	INSPECT WIRING HARNESS BETWEEN IG1 RELAY AND SAS CONTROL MODULE WARNING: Handling the component parts improperly can accidentally operate (deploy) the air bag module, which may seriously injure you. Read the service warnings/cautions and the article before handling the air bag system components. (Refer to AIR BAG SYSTEM SERVICE WARNINGS [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .) (Refer to AIR BAG SYSTEM SERVICE CAUTIONS [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .) Install the SRS1 7.5 A fuse. Remove the column cover. (Refer to COLUMN COVER REMOVAL/INSTALLATION .) Disconnect the clock spring connector. (Refer to CLOCK SPRING REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .) Remove the glove compartment. (Refer to GLOVE COMPARTMENT REMOVAL/INSTALLATION .) Disconnect the passenger-side air bag module connector. (Refer to PASSENGER-SIDE AIR BAG MODULE REMOVAL [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .) Disconnect the driver and passenger-side front seat connector. (Refer to FRONT SEAT REMOVAL/INSTALLATION .) Remove the B-pillar lower trim. (Refer to B-PILLAR LOWER TRIM REMOVAL/INSTALLATION .) Disconnect the driver and passenger-side pre-tensioner seat belt connectors. Disconnect the driver and passenger-side lap pre-tensioner seat belt connector. (Refer to FRONT SEAT BELT REMOVAL/INSTALLATION .) Remove the headliner. (Refer to HEADLINER REMOVAL/INSTALLATION .) Disconnect the driver and passenger-side curtain air bag module connectors. (Refer to CURTAIN AIR BAG MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .)	Yes	Go to the next step.
3		No	Refer to the wiring diagram and verify whether or not there is a common connector between SAS control module terminal and IG1 relay terminal. If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit or short to ground. Replace the malfunctioning part. If there is no common connector: Replace the wiring harness which has an open circuit or short to ground. Go to Step 5.
3	Disconnect the all SAS control module connectors. (Refer to SAS CONTROL MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .) Connect the negative battery cable. (Refer to NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Switch the ignition ON (engine off or on). Measure the voltage of SAS control module terminal 3C (Type A) (wiring harness-side)/3AD (Type B) (wiring harness-side). NOTE: Measure the voltage while shaking the wiring harness between the SAS control module and IG1 relay. Is the voltage between 8-17.9 V?
4	INSPECT SAS CONTROL MODULE CIRCUIT FOR OPEN CIRCUIT SAS control module connectors are disconnected. Switch the ignition off. Disconnect the negative battery cable and wait 1 min or more . (Refer to NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Inspect the wiring harness between SAS control module connector terminal 2C, 2F (Type A) (wiring harness-side)/2H, 2L (Type B) (wiring harness-side) and body ground. NOTE: Inspect for continuity while shaking the wiring harness between the SAS control module and body ground. Is there continuity?	Yes	Go to the next step.
4		No	Refer to the wiring diagram and verify whether or not there is a common connector between SAS control module terminal and body ground. If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit. Replace the malfunctioning part. If there is no common connector: Replace the wiring harness which has an open circuit. Go to the next step.
5	PERFORM SAS CONTROL MODULE DTC INSPECTION Connect the SAS control module connectors. Reconnect all disconnected connectors. Connect the negative battery cable. (Refer to NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Switch the ignition ON (engine off or on). Clear the DTC for the SAS control module using the M-MDS. (Refer to CLEARING DTC [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .) Perform the DTC inspection for the SAS control module using the M-MDS. (Refer to DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .) Are the same DTCs present?	Yes	Replace the SAS control module. (Refer to SAS CONTROL MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .)
5		No	DTC troubleshooting completed.