LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2016 >> 3 Sport, 4D Hatchback, Automatic Trans >> Repair and Diagnosis >> Body & Frame >> Door Locks >> On-Board Diagnostic - Start Stop Unit >> DTC Table

DTC Table

X: Applicable -: Not applicable
DTC No. KEY warning light (red) Push button start indicator light (amber) Description Fail-safe function Drive cycle Self test type(1) Memory function Refer to
B108B:23 - Flash Push button start switch 1 circuit malfunction X - C X (Refer to DTC B108B:23 [START STOP UNIT] .)
B108B:24 - Flash Push button start switch 1 circuit malfunction - - C X (Refer to DTC B108B:24 [START STOP UNIT] .)
B108C:23 - Flash Push button start switch 2 circuit malfunction X - C X (Refer to DTC B108C:23 [START STOP UNIT] .)
B108C:24 - Flash Push button start switch 2 circuit malfunction - - C X (Refer to DTC B108C:24 [START STOP UNIT] .)
B10AC:13(2) - - Cruise control switch circuit malfunction - - C X (Refer to DTC B10AC:13 [START STOP UNIT] .)
B10AC:23(2) - - Cruise control switch circuit malfunction - - C X (Refer to DTC B10AC:23 [START STOP UNIT] .)
B10C6:1F(3) On - Keyless antenna (exterior, rear) circuit malfunction X - C, D X (Refer to DTC B10C6:1F [ADVANCED KEYLESS ENTRY SYSTEM] .)
B10C7:1F(3) On - Keyless antenna (interior, rear) circuit malfunction X - C, D X (Refer to DTC B10C7:1F [ADVANCED KEYLESS ENTRY SYSTEM] .)
B10C9:1F On - Keyless antenna (interior, center) circuit malfunction (With keyless entry system) - - C, D X (Refer to DTC B10C9:1F [START STOP UNIT] .)
On - Keyless antenna (interior, front) circuit malfunction (With advanced keyless entry system) X - C, D X (Refer to DTC B10C9:1F [ADVANCED KEYLESS ENTRY SYSTEM] .)
B10D1:23(3) On - Request switch (LF) circuit malfunction - - C X (Refer to DTC B10D1:23 [ADVANCED KEYLESS ENTRY SYSTEM] .)
B10D3:23(3) On - Request switch (RF) circuit malfunction - - C X (Refer to DTC B10D3:23 [ADVANCED KEYLESS ENTRY SYSTEM] .)
B10D9:87 - Flash Coil antenna (built into push button start) error - - C - (Refer to SECURITY INDICATOR LIGHT: 11, DTC: B10D9:87/P1260:00 [IMMOBILIZER SYSTEM] .)
B10DA:51 - - Communication error with PCM (data received failure) - - C - (Refer to SECURITY INDICATOR LIGHT: 22, DTC: B10DA:51/P1260:00 [IMMOBILIZER SYSTEM] .)
B10DA:62 - - Communication error with PCM (code mismatched) - - C - (Refer to SECURITY INDICATOR LIGHT: 23, DTC: B10DA:62/P1260:00 [IMMOBILIZER SYSTEM] .)
B10E7:11 - Flash IG1 relay circuit malfunction - - C X (Refer to DTC B10E7:11 [START STOP UNIT] .)
B10E7:12 - Flash IG1 relay circuit malfunction - - C X (Refer to DTC B10E7:12 [START STOP UNIT] .)
B10E7:16 - Flash IG1 relay circuit malfunction - - C X (Refer to DTC B10E7:16 [START STOP UNIT] .)
B10E7:17 - Flash IG1 relay circuit malfunction - - C X (Refer to DTC B10E7:17 [START STOP UNIT] .)
B112A:11 - Flash IG2 relay circuit malfunction - - C X (Refer to DTC B112A:11 [START STOP UNIT] .)
B112A:12 - Flash IG2 relay circuit malfunction - - C X (Refer to DTC B112A:12 [START STOP UNIT] .)
B11C4:23(3) On - Request switch (liftgate) circuit malfunction - - C X (Refer to DTC B11C4:23 [ADVANCED KEYLESS ENTRY SYSTEM] .)
B11FD:1F(3) On - Keyless antenna (exterior, LF) circuit malfunction X - C, D X (Refer to DTC B11FD:1F [ADVANCED KEYLESS ENTRY SYSTEM] .)
B1210:1F(3) On - Keyless antenna (exterior, RF) circuit malfunction X - C, D X (Refer to DTC B1210:1F [ADVANCED KEYLESS ENTRY SYSTEM] .)
B124C:56 - - Turn switch circuit malfunction - - C X (Refer to DTC B124C:56 [START STOP UNIT] .)
B13C3:04(3) On - LF control unit internal malfunction X - C X (Refer to DTC B13C3:04 [ADVANCED KEYLESS ENTRY SYSTEM] .)
B13C3:09(3) On - LF control unit malfunction X - C X (Refer to DTC B13C3:09 [ADVANCED KEYLESS ENTRY SYSTEM] .)
B13C3:16(3) On - LF control unit power supply voltage low input X - C X (Refer to DTC B13C3:16 [ADVANCED KEYLESS ENTRY SYSTEM] .)
B13C3:29(3) On - Communication error between start stop unit and LF control unit X - C X (Refer to DTC B13C3:29 [ADVANCED KEYLESS ENTRY SYSTEM] .)
B13D3:05 - - Remote transmitter program error - - C - (Refer to SECURITY INDICATOR LIGHT: 13, DTC: B13D3:05/P1260:00 [IMMOBILIZER SYSTEM] .)
B13D3:16 - - Low remote transmitter battery voltage - - C X (Refer to DTC B13D3:16 [START STOP UNIT] .)
B13D3:4A On - Remote transmitter assembly malfunction - - C X (Refer to DTC B13D3:4A [START STOP UNIT] .)
B13D3:51 - Flash Unregistered remote transmitter is detected - - C - (Refer to SECURITY INDICATOR LIGHT: 15, DTC: B13D3:51/P1260:00 [IMMOBILIZER SYSTEM] .)
B13D3:94 - - Communication error with remote transmitter - - C - (Refer to SECURITY INDICATOR LIGHT: 13, DTC: B13D3:94/P1260:00 [IMMOBILIZER SYSTEM] .)
B13D3:97 - - Remote transmitter registration work not completed - - C X (Refer to DTC B13D3:97 [START STOP UNIT] .)
B13D4:00 On - Insufficient remote transmitter programming number - - C - (Refer to SECURITY INDICATOR LIGHT: 21, DTC: B13D4:00/P1260:00 [IMMOBILIZER SYSTEM] .)
B1C53:13 - - Windshield wiper switch circuit malfunction - - C X (Refer to DTC B1C53:13 [START STOP UNIT] .)
C0040:23(5) - Flash Brake switch (No. 1 signal) circuit malfunction X - C X (Refer to DTC C0040:23 [START STOP UNIT] .)
C0040:24(5) - Flash Brake switch (No. 1 signal) circuit malfunction X - C X (Refer to DTC C0040:24 [START STOP UNIT] .)
C0051:2F(4) - - Steering angle sensor signal error - - C X (Refer to DTC C0051:2F [START STOP UNIT] .)
C0051:95(4) - - Steering angle sensor assembly malfunction - - C X (Refer to DTC C0051:95 [START STOP UNIT] .)
C0052:14(4) - - Steering angle sensor A signal circuit malfunction - - C X (Refer to DTC C0052:14 [START STOP UNIT] .)
C0052:2F(4) - - Steering angle sensor A signal malfunction - - C X (Refer to DTC C0052:2F [START STOP UNIT] .)
C0053:14(4) - - Steering angle sensor B signal circuit malfunction - - C X (Refer to DTC C0053:14 [START STOP UNIT] .)
C0053:2F(4) - - Steering angle sensor B signal malfunction - - C X (Refer to DTC C0053:2F [START STOP UNIT] .)
C2003:13 - - Open circuit in steering switch - - C X (Refer to DTC C2003:13 [START STOP UNIT] .)
P0615:11 - Flash Starter relay circuit malfunction - - C X (Refer to DTC P0615:11 [START STOP UNIT] .)
P0615:12 - Flash Starter relay circuit malfunction X - C X (Refer to DTC P0615:12 [START STOP UNIT] .)
P0615:13 - Flash Starter relay circuit malfunction - - C X (Refer to DTC P0615:13 [START STOP UNIT] .)
P0615:16 - Flash Starter relay circuit malfunction - - C X (Refer to DTC P0615:16 [START STOP UNIT] .)
P0616:23 - - Circuit malfunction on downstream side of starter relay - - C X (Refer to DTC P0616:23 [START STOP UNIT] .)
P0616:24 - - Circuit malfunction on downstream side of starter relay - - C X (Refer to DTC P0616:24 [START STOP UNIT] .)
P0616:29 - - Downstream side of starter relay signal malfunction - - C X (Refer to DTC P0616:29 [START STOP UNIT] .)
P081C:23(5) - Flash NOT P position switch circuit malfunction X - C X (Refer to DTC P081C:23 [START STOP UNIT] .)
P081C:24(5) - Flash NOT P position switch circuit malfunction X - C X (Refer to DTC P081C:24 [START STOP UNIT] .)
P081D:29(6) - Flash Neutral switch error signal received X - C X (Refer to DTC P081D:29 [START STOP UNIT] .)
P081D:2F(6) - Flash Neutral switch signal mismatch X - C X (Refer to DTC P081D:2F [START STOP UNIT] .)
P0830:23(6) - Flash CPP switch circuit malfunction X - C X (Refer to DTC P0830:23 [START STOP UNIT] .)
P0850:23(5) - Flash Transaxle range sensor circuit malfunction X - C X (Refer to DTC P0850:23 [START STOP UNIT] .)
P0850:24(5) - Flash Transaxle range sensor circuit malfunction X - C X (Refer to DTC P0850:24 [START STOP UNIT] .)
P0930:71(5) - - Shift-lock solenoid circuit malfunction X - C X (Refer to DTC P0930:71 [START STOP UNIT] .)
P1708:24(6) - Flash Starter interlock switch circuit malfunction X - C X (Refer to DTC P1708:24 [START STOP UNIT] .)
P1708:29(6) - Flash Starter interlock switch circuit or CPP switch circuit malfunction X - C X (Refer to DTC P1708:29 [START STOP UNIT] .)
P1794:16 - Flash Start stop unit power supply voltage (terminal 2W) low input - - C X (Refer to DTC P1794:16 [START STOP UNIT] .)
U0001:88 On Flash Module communication error (HS-CAN) X - C X (Refer to DTC U0001:88/U0100:00/U0101:00/U0121:00/U0121:87/U0131:00/U0140:00/U0146:00/U0151:00/U0155:00 [START STOP UNIT] .)
U0028:87 On - Communication error with rear body control module (RBCM) - - C X (Refer to DTC U0028:87 [START STOP UNIT] .)
U0100:00 On Flash Communication error with PCM X - C X (Refer to DTC U0001:88/U0100:00/U0101:00/U0121:00/U0121:87/U0131:00/U0140:00/U0146:00/U0151:00/U0155:00 [START STOP UNIT] .)
U0100:87 - - Communication error with PCM (no response or data mismatch) - - C - (Refer to SECURITY INDICATOR LIGHT: 16, DTC: U0100:87/P1260:00 [IMMOBILIZER SYSTEM] .)
U0101:00(5) - Flash Communication error with TCM X - C X (Refer to DTC U0001:88/U0100:00/U0101:00/U0121:00/U0121:87/U0131:00/U0140:00/U0146:00/U0151:00/U0155:00 [START STOP UNIT] .)
U0121:00 On Flash Communication error with DSC HU/CM X - C X
U0121:87 On Flash Communication error with DSC HU/CM X - C X
U0131:00 - - Communication error with EPS control module X - C X
U0140:00 - - Communication error with front body control module (FBCM) X - C X
U0146:00 On Flash Communication error with instrument cluster X - C X
U0151:00 On Flash Communication error with SAS control module X - C X
U0155:00 On Flash Communication error with instrument cluster X - C X
U0447:86 On Flash Error signal received from instrument cluster X - C X (Refer to DTC U0447:86 [START STOP UNIT] .)
U201F:11 On - Keyless receiver circuit malfunction - - C X (Refer to DTC U201F:11 [START STOP UNIT] .)
U201F:12 On - Keyless receiver circuit malfunction - - C X (Refer to DTC U201F:12 [START STOP UNIT] .)
U2100:00 On - Start stop unit configuration not completed X - C X (Refer to DTC U2100:00 [START STOP UNIT] .)
U2300:00 - - Configuration data not received from instrument cluster X - C X (Refer to DTC U2300:00 [START STOP UNIT] .)
U3000:01(4) - - Start stop unit internal malfunction - - C X (Refer to DTC U3000:01 [START STOP UNIT] .)
U3000:49 On Flash Start stop unit internal malfunction X - C X (Refer to DTC U3000:49 [START STOP UNIT] .)
U3000:96 On Flash Start stop unit malfunction - - C X (Refer to DTC U3000:96 [START STOP UNIT] .)
On Flash Start stop unit malfunction - - C X (Refer to SECURITY INDICATOR LIGHT: 09, DTC: U3000:96/P1260:00 [IMMOBILIZER SYSTEM] .)
U3003:16 On - Start stop unit power supply voltage (terminal 1A) low input X - C X (Refer to DTC U3003:16 [START STOP UNIT] .)
U3004:11 - Flash ACC relay circuit malfunction - - C X (Refer to DTC U3004:11 [START STOP UNIT] .)
U3004:12 - Flash ACC relay circuit malfunction - - C X (Refer to DTC U3004:12 [START STOP UNIT] .)
U3004:16 - - ACC relay circuit malfunction - - C X (Refer to DTC U3004:16 [START STOP UNIT] .)
U3004:17 - - ACC relay circuit malfunction - - C X (Refer to DTC U3004:17 [START STOP UNIT] .)
(1) C: CMDTC self test, D: ODDTC self test
(2) With cruise control system
(3) With advanced keyless entry system
(4) With AFS, smart city brake support (SCBS), or blind spot monitoring (BSM) system
(5) ATX
(6) MTX
scientia non olet · About LEMON Manuals