LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2015 >> 3 SV, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 4 (Airbag System (Two-Step Deployment Control System)) >> Air Bag Module And Pre-TENSIONER Seat Belt Deployment Procedures [Two-Step Deployment Control System] >> Deployment Procedure for Outside of Vehicle >> Passenger-side Air Bag Module

Passenger-side Air Bag Module

WARNING: This page is about a different car, the 2014 Mazda 6. However, it is still accessible from the selected car via links, so may be relevant.
WARNING:
  • The passenger-side air bag module is a dual inflator type. If one inflator is forced to operate (deploy), the other may operate (deploy) accidentally. To prevent injury while disposing of the air bag module, make sure to operate (deploy) both passenger-side air bag module inflators simultaneously, following the procedure below.
NOTE:
  • The SSTs, two types of adapter harnesses (for inflators No. 1 and No. 2) and two deployment tools are to be used to operate (deploy) the passenger-side air bag module.
  1. Remove the following parts:
    1. Glove compartment (See GLOVE COMPARTMENT REMOVAL/INSTALLATION .)
    2. Bluetooth unit (with Bluetooth system) (See BLUETOOTH UNIT REMOVAL/INSTALLATION .)
  2. Remove the passenger-side air bag module. (See PASSENGER-SIDE AIR BAG MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .)
  3. Using a flathead screwdriver, lift the locking device carefully, however do not remove it.
  4. Disconnect the passenger-side air bag module connector.
  5. Connect the SST (Adapter harness)  to the passenger-side air bag module as shown in the figure.
    Fig 1: Disconnecting Passenger-Side Air Bag Module Connector
    G09787186Courtesy of MAZDA MOTORS CORP.
  6. Place the padded surface of the passenger-side air bag module facing the center of the tire as shown in the figure. To secure the air bag module to the tire wheel, wrap a wire (cross section 1.25 mm 2  {0.002 in 2  } or more)  through the tire and the bolt installation holes at least 4 times  as shown in the figure.
    WARNING:
    • If the air bag module is not properly secured to the tire, the tires may fall over by the impact of operation (deployment) and cause serious injury. To prevent this, secure the air bag module properly with the padded surface facing the center of the tire
    Fig 2: Placing Padded Surface Of Passenger-Side Air Bag Module Facing Center Of Tire
    G09787187Courtesy of MAZDA MOTORS CORP.
  7. Stack the tire with the passenger-side air bag module on top of two tires without wheels. Stack a tire without a wheel on top of the tire with the passenger-side air bag module, and then stack another tire with a wheel on the very top.
    Fig 3: Stacking Tire With Passenger-Side Air Bag Module On Top Of Two Tires Without Wheels
    G09076105Courtesy of MAZDA MOTORS CORP.
  8. Secure the tires with wire.
    Fig 4: Securing Tires With Wire
    G09076100Courtesy of MAZDA MOTORS CORP.
  9. Connect the SST (Deployment tool)  to the SST (Adapter harness). 
  10. Connect the SST (Deployment tool)  to the battery. Connect the power supply red clip to the positive battery terminal, and the black clip to the negative battery terminal.
  11. Verify that the red lamp on the SST (Deployment tool)  is illuminated.
  12. Verify that all persons are standing at least 6 m {20 ft}  away from the vehicle.
    Fig 5: Connecting SST (Deployment Tool) To SST (Adapter Harness)
    G09787190Courtesy of MAZDA MOTORS CORP.
  13. Press the activation switch on the SST (Deployment tool)  connected with 49 L066 002  (a yellow connector) of the SST (Adapter harness)  , and after 3 s  , press the activation switch on the other SST (Deployment tool)  to operate (deploy) the air bag module (both inflators).
    Fig 6: Pressing Activation Switch On Other SST (Deployment Tool) To Operate (Deploy) Air Bag Module
    G09076187Courtesy of MAZDA MOTORS CORP.
    WARNING:
    • Verify that air bag module operation (explosive) sound occurs twice. If no operation (explosive) sound was heard or a single operation (explosive) sound was heard, both inflators would not have operated (deployed) properly. This may cause serious injury if the air bag module operates (deploy) unexpectedly. If the two operation (explosive) sounds are not heard, perform Step 13 again. If a total of two operation (explosive) sounds cannot be verified even though Step 13 is performed again, leave the air bag module alone for 30 min or more before approaching it again.
    • The air bag module is very hot immediately after it is operated (deployed). You can be burned. Do not touch the air bag module for at least 15 min after deployment.
  14. Disconnect the SST (Deployment tool)  from the SST (Adapter harness)  .
scientia non olet · About LEMON Manuals