PID/DATA Monitor Table

PID name (definition)

Unit/Condition

Operation condition (reference)

Action

BRAKE_SW

Off/On

Brake pedal released: Off
Brake pedal depressed: On

Inspect the brake switch.
(See BRAKE SWITCH INSPECTION ).

BRK_F_P_C (Calculated Value)

Pa, psi

Brake pedal depressed: Changes according to the brake fluid pressure

Inspect the brake fluid pressure sensor.
(See BRAKE FLUID PRESSURE SENSOR INSPECTION ).

BRK_F_P_R (Raw Value)

DDS_MODE

Not_Learned/Learning/Learned

During initialization: Not_Learned
During learning: Learning
Learning completed⁽¹⁾: Learned

Perform the DTC inspection for the DSC HU/CM.
(See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)] ).

DSC_OFF_SW

Off/On

TCS OFF switch is released: Off
TCS OFF switch is depressed: On

Inspect the TCS OFF switch.
(See TCS OFF SWITCH INSPECTION ).

DSC_ST

Off/On

During TCS OFF mode: Off
Other than TCS OFF mode: On

Perform the DTC inspection for the DSC HU/CM.
(See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)] ).

LAT_ACCL_C (Calculated Value)

Vehicle stopped or driving at constant speed: 0 G
Cornering to left: Changes 0 G-positive
Cornering to right: Changes 0 G-negative

Perform the DTC inspection for the SAS control module.
(See DTC INSPECTION [STANDARD DEPLOYMENT CONTROL SYSTEM] ).
(See DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] ).

LAT_ACCL_R (Raw Value)

LON_ACCL_C (Calculated Value)

Vehicle stopped or driving at constant speed: 0 G
Vehicle is driving at a acceleration: Changes 0 G-positive
Vehicle is driving at a deceleration: Changes 0 G-negative

Perform the DTC inspection for the SAS control module.
(See DTC INSPECTION [STANDARD DEPLOYMENT CONTROL SYSTEM] ).
(See DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] ).

LON_ACCL_R (Raw Value)

P_BRAKE_SW

Off/On

Parking brake lever released: OFF
Parking brake lever pulled: ON

Inspect the parking brake switch.
(See PARKING BRAKE SWITCH INSPECTION ).

PMP_MT

Off/On

Pump motor not activated: Off
Pump motor activated: On

Inspect the DSC HU/CM.
(See DSC HU/CM INSPECTION ).

PMP_MT_SP

R_GEAR_SW

Off/On

Except shift/selector lever at R position: OFF
Shift/selector lever at R position: ON

Inspect the PCM. (MTX)
(See PCM INSPECTION [SKYACTIV-G 2.0] ).
Inspect the TCM. (ATX)
(See ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [FW6A-EL, FW6AX-EL] ).

STR_ANG_C (Calculated Value)

Steering wheel in neutral position (not turned): 0°
Steering wheel turned to left: Changes 0°-positive
Steering wheel turned to right: Changes 0°-negative

Inspect the EPS CM.
(See EPS CONTROL MODULE INSPECTION ).

STR_ANG_R (Raw Value)

TPMS_TYPE

No_DDS/DDS+TOM EU/DDS+TOM US

TPMS not equipped: No_DDS
TPMS equipped (Corresponding to European regulations): DDS+TOM_EU
TPMS equipped (Corresponding to U.S. regulations): DDS+TOM_US

Perform the DTC inspection for the DSC HU/CM.
(See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)] ).

V_INLET_LF

Off/On

Solenoid valve not activated: Off
Solenoid valve activated: On

Inspect the DSC HU/CM.
(See DSC HU/CM INSPECTION ).

V_INLET_LR

V_INLET_RF

V_INLET_RR

V_OUTLET_LF

V_OUTLET_LR

V_OUTLET_RF

V_OUTLET_RR

V_STB_LF/RR

Off/On

Solenoid valve activated: On
Solenoid valve not activated: Off

Inspect the DSC HU/CM.
(See DSC HU/CM INSPECTION ).

V_STB_RF/LR

V_TRC_LF/RR

Off/On

Solenoid valve activated: On
Solenoid valve not activated: Off

Inspect the DSC HU/CM.
(See DSC HU/CM INSPECTION ).

V_TRC_RF/LR

VPWR_B_SOL

Ignition switched ON (engine off): Approx. 12.2 V
Idling: Approx. 14.1 V

Inspect power supply circuit.
(See DSC HU/CM INSPECTION ).

VSPD

KPH, MPH

Vehicle stopped: 0 KPH, 0 MPH
Vehicle running: Vehicle speed

Inspect the DSC HU/CM.
(See DSC HU/CM INSPECTION ).

WSPD_SEN_LF

KPH, MPH

Vehicle stopped: 0 KPH, 0 MPH
Vehicle running: Vehicle speed

Inspect the front ABS wheel-speed sensor.
(See FRONT ABS WHEEL-SPEED SENSOR INSPECTION ).

WSPD_SEN_LR

Inspect the rear ABS wheel-speed sensor.
(See REAR ABS WHEEL-SPEED SENSOR INSPECTION [2WD] ).
(See REAR ABS WHEEL-SPEED SENSOR INSPECTION [AWD] ).

WSPD_SEN_RF

Inspect the front ABS wheel-speed sensor.
(See FRONT ABS WHEEL-SPEED SENSOR INSPECTION ).

WSPD_SEN_RR

Inspect the rear ABS wheel-speed sensor.
(See REAR ABS WHEEL-SPEED SENSOR INSPECTION [2WD] ).
(See REAR ABS WHEEL-SPEED SENSOR INSPECTION [AWD] ).

YAW_RATE_C (Calculated Value)

°/s

Vehicle stopped or driving straight: 0°/s
Cornering to left: Changes 0°/s-positive
Cornering to right: Changes 0°/s-negative

Perform the DTC inspection for the SAS control module.
(See DTC INSPECTION [STANDARD DEPLOYMENT CONTROL SYSTEM] ).
(See DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] ).

YAW_RATE_R (Raw Value)

⁽¹⁾	After ignition is switched off, switch it ON (engine off or on) and verify.