Security System And Locks System

Security And Locks Location Index
- Locks and Openers
- Advanced Keyless Entry And Start System and Immobilizer System
- Keyless Entry System and Immobilizer System
Outer Handle Removal/Installation
Inner Handle Removal/Installation
Open Hook Removal/Installation
Door Lock Switch Removal/Installation
Door Lock Switch Inspection
Hood Latch And Release Lever Removal/Installation
- Notes
- Hood Release Lever Removal Note
Hood Striker Removal/Installation
Hood Latch Switch Inspection
Fuel-Filler Lid Opener Removal/Installation
Door Key Cylinder Removal/Installation
Door Latch And Lock Actuator Removal/Installation
Door Lock Actuator Inspection
- Door Lock Actuator
- Door Lock-Link Switch
- Door Key Cylinder Switch
Door Lock Striker Removal/Installation
Trunk Lid Opener Removal/Installation
Trunk Lid Striker Removal/Installation
Trunk Lid Opener Inspection
Trunk Lid Opener Switch Removal/Installation
Trunk Key Cylinder Removal/Installation
Trunk Lid Opener Switch Inspection
Trunk Key Cylinder Switch Inspection
Trunk Lid Open Cancel Switch Removal/Installation
Trunk Lid Open Cancel Switch Inspection
Top Lock Switch Inspection
Keyless Control Module Removal/Installation
Keyless Control Module Inspection [Keyless Entry System]
- Notes
- Terminal Voltage Table (Reference)
Keyless Control Module Inspection [Advanced Keyless Entry And Start System]
- Notes
- Terminal Voltage Table (Reference)
Keyless Receiver Removal/Installation
- Front
- Rear
Keyless Receiver Inspection
- Front
  - Terminal Voltage Table (Reference)
- Rear
  - Terminal Voltage Table (Reference)
Transmitter Battery Replacement
Transmitter Id Code Registration
Immobilizer System-Related Parts Programming [Keyless Entry System]
- Foreword
- Selection of Procedure for Immobilizer System-Related Parts Programming
- M-MDS Connecting Procedure
- No. 1 Additional Key Programming Procedure (Using Two Valid Keys)
  - Conditions
  - Procedure
- No. 2 Additional Key Programming Procedure (Using the M-MDS)
  - Conditions
  - Procedure
- No. 3 Additional Key Programming Procedure Changing
  - Notes
  - Procedure
- No. 4 Programming Procedure Due to PCM Replacement
  - Conditions
  - Procedure
- No. 5 Programming Procedure Due to Keyless Control Module Replacement
- No. 6 Programming Procedure Due to Simultaneous Replacement of Immobilizer System-related Parts (PCM and Keyless Control Module)
Immobilizer System-Related Parts Programming [Advanced Keyless Entry And Start System]
- Foreword
- Selection of Procedure for Immobilizer System-Related Parts Programming
- M-MDS Connecting Procedure
- No. 1 Additional Key Programming Procedure (Using Two Valid Keys)
- No. 2 Additional Key Programming Procedure (Using the M-MDS)
- No. 3 Additional Key Programming Procedure Changing
  - Notes
  - Procedure
- No. 4 Programming Procedure Due to PCM Replacement
- No. 5 Programming Procedure Due to Steering Lock Unit Replacement
- No. 6 Programming Procedure Due to Keyless Control Module Replacement
- No. 7 Programming Procedure Due to Simultaneous Replacement of Immobilizer System-related Parts (PCM, Keyless Control Module, and Steering Lock Unit)
  - Notes
  - Procedure
Steering Lock Unit Id Code Registration
Keyless Control Module Configuration
Customized Function Setting Procedure
Keyless Antenna Removal/Installation
- LH, RH
- Rear
- Instrument panel
- Center
- Rear NO. 2
- Trunk
Keyless Beeper Removal/Installation
Request Switch Removal/Installation
- Driver-Side/Passenger-Side
- Trunk Lid
Request Switch Inspection
Advanced Key Battery Replacement
Coil Antenna Removal/Installation
Clearing Advanced Key
Advanced Key Id Code Registration
- Notes
- With Two Programmed Advanced Keys
- Using M-MDS
Fuel-Filler Lid Opener Lever And Cable Removal/Installation
- Fuel-Filler Lid Opener Lever
- Fuel-Filler Lid Opener Cable