LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2011 >> RX-8 R3, 1.3 2 >> Repair and Diagnosis >> Body & Frame >> Door Locks >> Security System And Locks System >> Immobilizer System-Related Parts Programming [With Keyless Entry System] >> No. 6 Programming Procedure Due To Simultaneous Replacement of Immobilizer System-related Parts (PCM and Keyless Control Module) >> Procedure

No. 6 Programming Procedure Due To Simultaneous Replacement of Immobilizer System-related Parts (PCM and Keyless Control Module): Procedure

Fig 1: Key Reference Chart (Due To Simultaneous Replacement Of Immobilizer System-Related Parts)
G05986036Courtesy of MAZDA MOTORS CORP.
KEY PROGRAMMING PROCEDURE

Step Procedure Action after procedure
1 REPLACE KEYLESS CONTROL MODULE. 
Refer to KEYLESS CONTROL MODULE REMOVAL/INSTALLATION to perform keyless control module replacement. (See KEYLESS CONTROL MODULE REMOVAL/INSTALLATION .)		 Go to the next step.
2 REPLACE PCM 
Refer to PCM REMOVAL/INSTALLATION to perform PCM replacement. (See PCM REMOVAL/INSTALLATION [13B-MSP] .)		 Go to the next step.
3 PERFORM PARAMETER RESET 
  1. Connect the M-MDS to the DLC-2. (See M-MDS CONNECTING PROCEDURE .)
  2. Turn the ignition switch to the ON position using a valid key.
    NOTE:
    • Although the security light remains illuminated and DTC 15 is displayed after approx. 1 min  , continue to perform the procedure as indicated.
  3. Verify that the keyless warning light illuminates for approx. 3 s  , and then turns off.
  4. After vehicle identification, select the following from the M-MDS initial screen.
    • Using an IDS (laptop PC):
      1. Select the "Body"
      2. Select the "Security"
      3. Select the "PATS function"
      4. Select the "Parameter Reset"
    • Using a PDS (pocket PC):
      1. Select the "All Tests and Calibrations"
      2. Select the "PATS Functions"
      3. Select the "Parameter Reset"
  5. Perform the security access according to the directions on the M-MDS screen.
  6. Select the replaced parts according to the directions on the M-MDS screen.
    • If the keyless control module is replaced: Select "RKE".
    • If the PCM is replaced: Select "PCM".
    CAUTION:
    • At this time, do not select the other parts from the M-MDS menu.
  7. Verify that the PATS function menu is displayed again on the M-MDS screen.
 Go to the next step.
4 CLEAR IGNITION KEY ID NUMBERS 
  1. Select "Ignition Key Code Erase and Program" from the M-MDS screen menu.
  2. Clear the ignition key ID number according to the directions on the M-MDS.
 Go to the next step.
5 PERFORM IGNITION KEY ID NUMBER PROGRAMMING 
  1. Program two keys according to the directions on the M-MDS.
  2. After verifying that the PATS function menu is displayed again on the M-MDS screen, select "Finish (this menu)".
  3. Turn the ignition switch to the LOCK position.
  4. Turn the ignition switch to the ON position.
  5. Verify that the security light illuminates for approx. 3 s  , and then turns off.
  6. Turn the ignition switch to the LOCK position.
  7. Disconnect the M-MDS from the DLC-2.
 Go to the next step.
6 VERIFY PROGRAMMING IS PERFORMED CORRECTLY 
  1. Verify that the engine can be started with all the keys.
  2. Can the engine be started?
 Yes Procedure is completed
No Perform the corresponding DTC inspection to repair the malfunctioning part.
scientia non olet · About LEMON Manuals