Diagnostic Procedure

DTC P0134:00 (LF, L5) DIAGNOSTIC PROCEDURE

STEP	INSPECTION		ACTION
1	VERIFY SNAPSHOT DATA AND DIAGNOSTIC MONITORING TEST RESULTS HAVE BEEN RECORDED Have the snapshot data and DIAGNOSTIC MONITORING TEST RESULTS (A/F sensor, HO2S related) been recorded?	Yes	Go to the next step.
1		No	Record the snapshot data and DIAGNOSTIC MONITORING TEST RESULTS on repair order, then go to the next step.
2	VERIFY RELATED REPAIR INFORMATION AVAILABILITY Verify related Service Bulletins and/or on-line repair information availability. Is any related repair information available?	Yes	Perform repair or diagnosis according to the available repair information. If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	VERIFY RELATED PENDING CODE AND STORED DTC NOTE: If fuel monitor DTC, DTC P0132:00 is retrieved, ignore it until P0134:00 is fixed. Switch the ignition to off, then to ON (engine off). Perform the DTC Reading Procedure and Pending Trouble Code Access Procedure. (See ON-BOARD DIAGNOSTIC TEST .) Is the DTC P2237:00 or P2251:00 also present?	Yes	Go to the applicable DTC inspection. (See DTC P2237:00 .) (See DTC P2251:00 .)
3		No	Go to the next step.
4	IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA (MODE 2) Perform the Freeze Frame PID Data Access Procedure. (See ON-BOARD DIAGNOSTIC TEST .) Is the DTC P0134:00 on FREEZE FRAME DATA (Mode 2)?	Yes	Go to the next step.
4		No	Go to the troubleshooting procedures for DTC on FREEZE FRAME DATA (Mode 2). (See DTC TABLE .)
5	INSPECT A/F SENSOR CONNECTOR CONDITION Switch the ignition to off. Disconnect the A/F sensor connector. Inspect for poor connection (such as damaged/pulled-out pins, corrosion). Is there any malfunction?	Yes	Repair or replace the terminal and/or connector, then go to Step 14.
5		No	Go to the next step.
6	INSPECT A/F SENSOR HEATER Inspect the A/F sensor heater. (See AIR FUEL RATIO (A/F) SENSOR INSPECTION .) Is there any malfunction?	Yes	Replace the A/F sensor, then go to Step 14. (See AIR FUEL RATIO (A/F) SENSOR REMOVAL/INSTALLATION .)
6		No	Go to the next step.
7	INSPECT A/F SENSOR CIRCUIT FOR SHORT TO GROUND A/F sensor connector is disconnected. Inspect for continuity between the following terminals (wiring harness-side) and body ground: A/F sensor terminal E A/F sensor terminal B A/F sensor terminal D A/F sensor terminal F Is there continuity?	Yes	If the short to ground circuit could be detected: Repair or replace the wiring harness for a possible short to ground. If the short to ground circuit could not be detected: Replace the PCM (short to ground in PCM internal circuit). (See PCM REMOVAL/INSTALLATION .) Go to Step 14.
7		No	Go to the next step.
8	INSPECT PCM CONNECTOR CONDITION Disconnect the PCM connector. Inspect for poor connection (such as damaged/pulled-out pins, corrosion). Is there any malfunction?	Yes	Repair or replace the terminal and/or connector, then go to Step 14.
8		No	Go to the next step.
9	INSPECT A/F SENSOR CIRCUIT FOR OPEN CIRCUIT A/F sensor and PCM connectors are disconnected. Inspect for continuity between the following terminals (wiring harness-side): A/F sensor terminal E-PCM terminal 2A A/F sensor terminal B-PCM terminal 2AD A/F sensor terminal D-PCM terminal 2AC A/F sensor terminal F-PCM terminal 2Z Is there continuity?	Yes	Go to the next step.
9		No	Repair or replace the wiring harness for a possible open circuit, then go to Step 14.
10	INSPECT GAS LEAKAGE FROM EXHAUST SYSTEM Reconnect the A/F sensor connector. Visually inspect if there is any gas leakage between the exhaust manifold and A/F sensor. Is there gas leakage?	Yes	Repair or replace the malfunctioning part according to inspection results, then go to Step 14.
10		No	Go to the next step.
11	INSPECT SEALING OF ENGINE COOLANT PASSAGE Perform the "ENGINE COOLANT LEAKAGE INSPECTION". (See ENGINE COOLANT LEAKAGE INSPECTION .) Is there any malfunction?	Yes	Repair or replace the malfunctioning part according to inspection results, then go to Step 14.
11		No	Go to the next step.
12	INSPECT ENGINE COMPRESSION Inspect the engine compression. (See COMPRESSION INSPECTION .) Is there any malfunction?	Yes	Repair or replace the malfunctioning parts according to the inspection results, then go to Step 14.
12		No	Go to the next step.
13	INSPECT A/F SENSOR Inspect the A/F sensor. (See AIR FUEL RATIO (A/F) SENSOR INSPECTION .) Is there any malfunction?	Yes	Replace the A/F sensor, then go to the next step. (See AIR FUEL RATIO (A/F) SENSOR REMOVAL/INSTALLATION .)
13		No	Go to the next step.
14	VERIFY DTC TROUBLESHOOTING COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE .) Start the engine and warm it up completely. Perform the Drive Mode 03 (EGR System, A/F sensor heater, HO2S heater, A/F sensor, HO2S and TWC Repair Verification Drive Mode). (See OBD-II DRIVE MODE .) Is the PENDING CODE for this DTC present?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION .)
14		No	Go to the next step.
15	VERIFY AFTER REPAIR PROCEDURE Perform the "AFTER REPAIR PROCEDURE". (See AFTER REPAIR PROCEDURE .) Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE .)
15		No	DTC troubleshooting completed.