LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2009 >> Tribute i Sport, 4WD, Standard >> Repair and Diagnosis >> General Information >> Specifications Index >> Common Specs & Procedures -- Tribute >> Specifications Index

Specifications Index

TRIBUTE SPECIFICATIONS INDEX

System Specification/Procedure
Air Conditioning
Service TECHNICAL DATA (CLIMATE CONTROL)
Torque See Torque Specifications in text and appropriate graphics under BASIC SYSTEM (HVAC) - 2.5L & 3.0L .
Axle Nut/Hub Nut
Front 222 Ft. Lbs. (300 N.m)
Rear 221 Ft. Lbs. 300 N.m)
Battery BATTERY REMOVAL/INSTALLATION
Brakes
Bleeding Sequence BRAKE SYSTEM BLEEDING
Disc Brakes
Service Specifications GENERAL SPECIFICATIONS
Torque TORQUE SPECIFICATIONS
Drum Brakes
Service Specifications GENERAL SPECIFICATIONS
Torque TORQUE SPECIFICATIONS
Charging
Generator
2.5L 4-Cyl. GENERATOR REMOVAL/INSTALLATION -- 2.5L
3.0L V6 GENERATOR REMOVAL/INSTALLATION -- 3.0L
Torque
2.5L 4-Cyl. See Torque Specifications in appropriate graphics under GENERATOR REMOVAL/INSTALLATION -- 2.5L .
3.0L V6 See Torque Specifications in appropriate graphics under GENERATOR REMOVAL/INSTALLATION -- 3.0L .
Drive Belts
Adjustment
2.5L 4-Cyl. ACCESSORY DRIVE -- 2.5L
3.0L V6 ACCESSORY DRIVE -- 3.0L
Belt Routing
2.5L 4-Cyl. ACCESSORY DRIVE BELT ROUTING
3.0L V6 ACCESSORY DRIVE -- 3.0L
Engine Cooling
General Service Specifications
2.5 4-Cyl. ENGINE COOLING DESCRIPTION AND OPERATION -- 2.5L
3.0L V6 ENGINE COOLING DESCRIPTION/OPERATION -- 3.0L
Radiator Cap Pressure 13-18 psi
Thermostat R & I
2.5L 4-Cyl. THERMOSTAT HOUSING REMOVAL/INSTALLATION -- 2.5L
3.0L V6 THERMOSTAT REMOVAL/INSTALLATION -- 3.0L
Water Pump R & I
2.5L 4-Cyl. WATER PUMP REMOVAL/INSTALLATION -- 2.5L
3.0L V6 WATER PUMP REMOVAL/INSTALLATION -- 3.0L
Engine Mechanical
2.5L 4-Cyl.
Compression COMPRESSION TEST
Oil Pressure (Engine HOT) 29-39 psi (200-268 kPa) at 2,000 RPM
Overhaul 2.5L ENGINE
Torque TECHNICAL DATA (ENGINE)
3.0L V6
Compression COMPRESSION TEST
Oil pressure (MINIMUM with Engine warm) 11 psi (76 kPa) at 1,500 RPM
Overhaul MECHANICAL - 3.0L
Torque See Torque Specifications in text or appropriate graphics under MECHANICAL - 3.0L .
Fluid Specifications See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flex Plate/Drive Plate Torque
2.5L 4-Cyl.
First Step 37 Ft. Lbs. (50 N.m)
second Step 59 Ft. Lbs. (80 N.m)
Final Step 83 Ft. Lbs. (112 N.m)
3.0L V6 59 Ft. Lbs. (80 N.m)
Fuel System
Pressure Specification 55-70 psi (379-483 kPa)
Fuel Pressure Test Procedure FUEL SYSTEM PRESSURE TEST
Fuel Filter Location and R & I FUEL FILTER REMOVAL/INSTALLATION
Ignition
Firing Order & Cylinder Identification
2.5L 4-Cyl. FIRING ORDER & CYLINDER IDENTIFICATION
3.0L V6 FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Resistance) The 2.3L and 3.0L engines are equipped with coil-on-plug ignition.
Ignition Wires (Routing) The 2.3L and 3.0L engines are equipped with coil-on-plug ignition.
Spark Plug
2.5L 4-Cyl. (Motorcraft Cyls, 1 & 3: AZFS-32F; Cyls. 2 & 4: AZFS-32FE)
Gap 0.052-0.56 in. (1.3-1.4 mm)
Torque 106 In. Lbs. (12 N.m)
3.0L V6 (Motorcraft AGSF-32M)
Gap .051-.055 in. (1.3-1.4 mm)
Torque 133 In. Lbs. (15 N.m)
Starting
Starter STARTING SYSTEM
Torque
2.5L 4-Cyl. See Torque Specifications in text or appropriate graphics under STARTER MOTOR REMOVAL/INSTALLATION -- 2.5L .
3.0L V6 See Torque Specifications in text or appropriate graphics under STARTER MOTOR REMOVAL/INSTALLATION -- 3.0L .
Wheel Alignment
Adjustment Specifications WHEEL ALIGNMENT
Torque See Torque Specifications in text under WHEEL ALIGNMENT .
Wheel & Tire
Wheel Lug Nut Torque 100 Ft. Lbs. (135 N.m)