LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2009 >> RX-8 R3, 1.3 2 >> Repair and Diagnosis >> Body & Frame >> Door Locks >> Security System And Locks System >> Immobilizer System-Related Parts Programming [With Advanced Keyless System] >> No. 5 Programming Procedure Due to Steering Lock Unit Replacement >> Procedure

No. 5 Programming Procedure Due to Steering Lock Unit Replacement: Procedure

Fig 1: Key Reference Chart (Due To Steering Lock Unit Replacement)
G05986020Courtesy of MAZDA MOTORS CORP.
KEY PROGRAMMING PROCEDURE

Step Procedure Action after procedure
1 REPLACE STEERING LOCK UNIT 
Replace the steering lock unit. (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION .)		 Go to the next step.
2 CLEAR IGNITION KEY ID NUMBERS 
  1. Connect the M-MDS to the DLC-2. (See M-MDS CONNECTING PROCEDURE .)
  2. Turn the ignition switch to the ON position using key 1.
    NOTE:
    • Although the security light starts flashing and DTC 15 is displayed after approx. 1 min  , this does not indicate an improper procedure. Continue to perform the procedure as indicated.
  3. After vehicle identification, select the following from the M-MDS initial screen.
    • Using an IDS (laptop PC):
      1. Select the "Body"
      2. Select the "Security"
      3. Select the "PATS function"
      4. "Ignition Key Code Erase and Program"
    • Using a PDS (pocket PC):
      1. Select the "All Tests and Calibrations"
      2. Select the "PATS Functions"
      3. "Ignition Key Code Erase and Program"
  4. Perform the security access according to the directions on the M-MDS screen.
 Go to the next step.
3 PERFORM IGNITION KEY ID NUMBER PROGRAMMING 
  1. Program two keys according to the directions on the M-MDS.
  2. Verify that the PATS function menu is displayed again on the M-MDS screen.
 Go to the next step.
4 PERFORM STEERING LOCK UNIT PROGRAMMING 
  1. Select "Steering Lock Unit Programming" from the M-MDS screen menu.
  2. Complete the Steering Lock Unit Programming according to the directions on the M-MDS. (See STEERING LOCK UNIT ID CODE REGISTRATION [WITH ADVANCED KEYLESS SYSTEM] .)
  3. After verifying that the PATS function menu is displayed again on the M-MDS screen, select "Finish (this menu)".
  4. Turn the ignition switch to the LOCK position.
  5. Disconnect the M-MDS from the DLC-2.
  6. Remove the programmed card key from the vehicle.
 Go to the next step.
5 VERIFY KEY 1 PROGRAMMING PERFORMED CORRECTLY 
  1. Start the engine using key 1.
  2. Verify that the security light and keyless warning light operate as shown in the following figure.
  3. Turn the ignition switch to the LOCK position and remove key 1.
G05986021Courtesy of MAZDA MOTORS CORP.
 Go to the next step.
6 VERIFY KEY 2 PROGRAMMING PERFORMED CORRECTLY 
  1. Start the engine using key 2.
  2. Verify that the security light and keyless warning light operate as shown in the following figure.
  3. Turn the ignition switch to the LOCK position and remove key 2.
  4. Are there other keys to be programmed?
G05986022Courtesy of MAZDA MOTORS CORP.
 Yes Repeat Step 6 using each programmed key.
No Go to the next step.
7 VERIFY CARD KEY PROGRAMMING PERFORMED CORRECTLY 
  1. Bring the programmed card key into the vehicle.
  2. Close all doors.
  3. Remove the key from the key cylinder and place it on the front passenger's seat.
  4. Start the engine using the card key.
  5. Verify that the security light and keyless warning light operate as shown in the following figure.
  6. After verifying that the keyless warning light turns off, turn the ignition switch to the LOCK position.
G05986023Courtesy of MAZDA MOTORS CORP.
 Procedure is completed
scientia non olet · About LEMON Manuals