LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2007 >> 3 i, 2.0 F, Automatic >> Repair and Diagnosis >> Restraints >> Restraints Control Systems >> On-Board Diagnostic (Restraints) >> PID/Data Monitor Table

PID/Data Monitor Table

PID/DATA MONITOR CHART

PID name (definition) Unit/Condition Operation Condition (Reference) Terminal
CCNT_RCM (Number of continuous DTCs) -
  • DTCs detected: 1-255
  • No DTCs detected: 0
 -
CRSH_RC
(Number of collisions detected)		 -
  • Collisions detected: 1-255
  • No collisions detected: 0
 -
D_ABAGR2
(Driver-side air bag module (inflator No.2) resistance)		 Ohm Under any condition: 1.5-3.7 ohms 1U, 1Q
DABAGR
(Driver-side air bag module (inflator No.1) resistance)		 Ohm Under any condition: 1.5-3.7 ohms 11, 1M
DFCURTRES
(Driver-side curtain air bag module resistance)		 Ohm Under any condition: 1A-3.2 ohms 2AG, 2AK
DR_BUKL
(Driver-side buckle switch status)		 Buckled/Unbuckled
  • Driver-side buckle switch on: Buckled
  • Driver-side buckle switch off: Unbuckled
 2W
DR_PTENS
(Driver-side pre-tensioner seat belt resistance)		 Ohm Under any condition: 1.5-3.1 ohms 2J, 2N
DS_AB
(Driver-side side air bag module resistance)		 Ohm Under any condition: 1A-3.2 ohms 2B, 2F
OCS_CAL_ST(1) (Seat weight sensor calibration status) Started/Calibrated/FL_Other/FL_Voltage/FL_Weight/FL_Timeout/In Progress FL_OCS
  • Seat weight sensor calibration start-up: Started
  • Seat weight sensor calibration completed normally: Calibrated
  • Seat weight sensor calibration command being sent: FL_Other
  • Voltage malfunction during seat weight sensor calibration: FL_Voltage
  • Weight error during seat weight sensor calibration: FL_Weight
  • Seat weight sensor calibration time limit passed: FL_Timeout
  • Seat weight sensor calibration being processed: In Progress
  • Seat weight sensor or Seat weight sensor control module malfunction: FL_OCS
 2AJ
OCS_DTC_ST(1) (Seat weight sensor status) Started/Cleared/In Progress/Failed Fault information cleared at seat weight sensor 2AJ
OCS_FLT
(Passenger sensing system status)		 MOD_FAIL/COMM_FAIL/CAL_FAIL/LHS_FAIL/RHS_FAIL/BTS_FAIL/No_Fault
  • Seat weight sensor control module malfunction: MOD_FAIL
  • Seat weight sensor control module communication error: COMM_FAIL
  • Seat weight sensor calibration error: CAL_FAIL
  • Seat weight sensor (LH) malfunction: LHS_FAIL
  • Seat weight sensor (RH) malfunction: RHS_FAIL
  • Passenger-side front buckle switch malfunction: BTS_FAIL
  • Passenger sensing system is normal: No_Fault
 2AJ
OCSSTAT(1)
(Seat weight sensor status)		 Empty/Below Threshold/Indeterminate/Above Threshold/Invalid Occupant classification status determined by seat weight sensor 2AJ
P_ABAGR2
(Passenger-side air bag module (inflator No.2) resistance)		 Ohm Under any condition: 1A-2.9 ohms 1R, 1V
PABAGR
(Passenger-side air bag module (inflator No. 1) resistance)		 Ohm Under any condition: 1.4-2.9 ohms U, 1N
PFCURTRES
(Passenger-side curtain air bag module resistance)		 Ohm Under any condition: 1.4-3.2 ohms 2AH, 2AL
PS_AB
(Passenger-side side air bag module resistance)		 Ohm Under any condition: 1A-3.2 ohms 21, 2M
PS_BUKL
(Passenger-side buckle switch status)		 Buckled/UNbuckled
  • Passenger-side buckle switch on: Buckled
  • Passenger-side buckle switch off: Unbuckled
 2C
PS_PTENS
(Passenger-side pre-tensioner seat belt resistance)		 Ohm Under any condition: 1.5-3.1 ohms 2A, 2E
PS_WEIGHT
(Seat weight sensor measured weight of passenger)		 Kg Display of load (body weight) on passenger-side seat 2AJ
TRAK_SW
(Seat track position sensor state)		 Forward/Rearward
  • Front seat front position: Forward
  • Front seat rear position: Rearward
 2AB, 2AF
VBATTRCM
(SAS control module input voltage)		 V Ignition switch is at ON: B+ 1D
(1) Used during seat weight sensor calibration setting. Not necessary for diagnostic.
scientia non olet · About LEMON Manuals