Diagnostic Trouble Code (DTC) Index - Powertrain Control Module (Pcm)
DIAGNOSTIC TROUBLE CODE - POWERTRAIN CONTROL MODULE INDEX
| DTC | DESCRIPTION | CONDITION | ACTION |
|---|---|---|---|
| P0030 | HO2S Heater Control Circuit (Bank 1, Sensor 1) | Front HO2S of Bank 1 heater circuit is open, shorted to ground, shorted to VPWR or has low or high current draw. | See HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT . |
| P0031 | HO2S Heater Control Circuit Low (Bank 1, Sensor 1) | Front HO2S of Bank 1 heater circuit is open, shorted to ground, shorted to VPWR or has low or high current draw. | See HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT . |
| P0032 | HO2S Heater Control Circuit High (Bank 1, Sensor 1) | Front HO2S of Bank 1 heater circuit is open, shorted to ground, shorted to VPWR or has low or high current draw. | See HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT . |
| P0037 | HO2S Heater Control Circuit Low (Bank 1, Sensor 2) | Rear HO2S of Bank 1 heater circuit is open, shorted to ground, shorted to VPWR or has low or high current draw. | See HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT . |
| P0038 | HO2S Heater Control Circuit High (Bank 1, Sensor 2) | Rear HO2S of Bank 1 heater circuit is open, shorted to ground, shorted to VPWR or has low or high current draw. | See HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT . |
| P0040 | Oxygen Sensor (HO2S) Signals Swapped Bank 1 Sensor 1 / Bank 2 Sensor 1 | During KOER testing the front HO2S signal(s) response for a fuel shift to the correct engine bank was not indicated. | See HEATED OXYGEN SENSOR (HO2S) SIGNALS . |
| P0041 | Oxygen Sensor (HO2S) Signals Swapped Bank 1 Sensor 2 / Bank 2 Sensor 2 | During KOER testing the front HO2S signal(s) response for a fuel shift to the correct engine bank was not indicated. | See HEATED OXYGEN SENSOR (HO2S) SIGNALS . |
| P0051 | HO2S Heater Control Circuit Low (Bank 2, Sensor 1) | Front HO2S of Bank 2 heater circuit is open, shorted to ground, shorted to VPWR or has low or high current draw. | See HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT . |
| P0052 | HO2S Heater Control Circuit High (Bank 2, Sensor 1) | Front HO2S of Bank 2 heater circuit is open, shorted to ground, shorted to VPWR or has low or high current draw. | See HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT . |
| P0053 | HO2S Heater Resistance (Bank 1, Sensor 1) | Front HO2S of Bank 1 heater circuit is open, shorted to ground, shorted to VPWR or has low or high current draw. | See HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT . |
| P0054 | HO2S Heater Resistance (Bank 1, Sensor 2) | Rear HO2S of Bank 1 heater circuit is open, shorted to ground, shorted to VPWR or has low or high current draw. | See HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT . |
| P0057 | HO2S Heater Control Circuit Low (Bank 2, Sensor 2) | Rear HO2S of Bank 2 heater circuit is open, shorted to ground, shorted to VPWR or has low or high current draw. | See HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT . |
| P0058 | HO2S Heater Control Circuit High (Bank 2, Sensor 2) | Rear HO2S of Bank 2 heater circuit is open, shorted to ground, shorted to VPWR or has low or high current draw. | See HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT . |
| P0059 | HO2S Heater Resistance (Bank 2, Sensor 1) | Front HO2S of Bank 2 heater circuit is open, shorted to ground, shorted to VPWR or has low or high current draw. | See HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT . |
| P0060 | HO2S Heater Resistance (Bank 2, Sensor 2) | Rear HO2S of Bank 2 heater circuit is open, shorted to ground, shorted to VPWR or has low or high current draw. | See HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT . |
| P0068 | MAP / MAF - Throttle Position Correlation | TP signal went below 0.24 volts with load greater than 55 percent, or TP signal went above 2.44 volts with load less than 30 percent. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P0100 | Mass or Volume Air Flow A Circuit | MAF/IAT signal went out of range. | See MASS AIR FLOW (MAF) SENSOR . |
| P0101 | Mass or Volume Air Flow A Circuit Range/Performance | MAF/IAT signal went out of range. | See MASS AIR FLOW (MAF) SENSOR . |
| P0102 | Mass or Volume Air Flow A Circuit Low | MAF/IAT signal went below 0.23 volts sometime during normal engine operation or KOER Self-Test. | See MASS AIR FLOW (MAF) SENSOR . |
| P0103 | Mass or Volume Air Flow A Circuit High | MAF/IAT signal went above 4.60 volts during engine operation or KOER Self-Test. | See MASS AIR FLOW (MAF) SENSOR . |
| P0104 | Mass or Volume Air Flow A Circuit Intermittent/Erratic | A concern exists in the mass air flow (MAF) sensor A circuit, or the air tube containing the sensor, causing an incorrect air flow reading. | See MASS AIR FLOW (MAF) SENSOR . |
| P0105 | Manifold Absolute Pressure/BARO Circuit | Manifold Absolute Pressure (MAP) sensor input to the powertrain control module (PCM) is not within the calibrated value. | See MANIFOLD ABSOLUTE PRESSURE (MAP)SENSOR . |
| P0106 | Manifold Absolute Pressure/BARO Sensor Range/Performance | Manifold Absolute Pressure (MAP) sensor input to the powertrain control module (PCM) is not within the calibrated value. | See MANIFOLD ABSOLUTE PRESSURE (MAP)SENSOR . |
| P0107 | Manifold Absolute Pressure/BARO Sensor Low | MAP sensor operating voltage went below 0.25 volts. | See MANIFOLD ABSOLUTE PRESSURE (MAP)SENSOR . |
| P0108 | Manifold Absolute Pressure/BARO Sensor High | MAF/IAT signal went above 4.60 volts during engine operation or KOER Self-Test. | See MANIFOLD ABSOLUTE PRESSURE (MAP)SENSOR . |
| P0109 | Manifold Absolute Pressure/BARO Sensor Intermittent | The sensor input to the powertrain control module (PCM) is failing intermittently. | See MANIFOLD ABSOLUTE PRESSURE (MAP)SENSOR . |
| P0110 | Intake Air Temperature (IAT) Sensor 1 Circuit | IAT sensor signal was out of range. | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P0111 | Intake Air Temperature (IAT) Sensor 1 Circuit Range/Performance | IAT sensor signal was out of range. | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P0112 | Intake Air Temperature (IAT) Sensor 1 Circuit Low | IAT sensor signal is less than 0.2 volts or 121°C (250°F). | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P0113 | Intake Air Temperature (IAT) Sensor 1 Circuit High | IAT signal is greater than the Self-Test maximum of 4.6 volts -50°C (-58°F). | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P0114 | Intake Air Temperature (IAT) Sensor 1 Intermittent/Erratic | IAT sensor signal is erratic. | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P0115 | Engine Coolant Temperature (ECT) Sensor 1 Circuit | ECT sensor signal was out of range. | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P0116 | Engine Coolant Temperature Sensor 1 Circuit Range/Performance | Engine coolant temperature circuit range/performance failure. | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P0117 | Engine Coolant Temperature Sensor 1 Circuit Low | ECT / CHT sensor is less than the Self-Test minimum of less than 0.2 volt 121°C (250°F). | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P0118 | Engine Coolant Temperature Sensor 1 Circuit High | ECT / CHT sensor signal is greater than the Self-Test maximum of 4.6 volts -50°C (-46°F). | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P0119 | Engine Coolant Temperature Sensor 1 Circuit Intermittent/Erratic | ECT / CHT sensor signal is intermittent. | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P0120 | Throttle/Pedal Position Sensor A Circuit | Throttle position (TP) sensor out of range. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P0121 | Throttle/Pedal Position Sensor A Circuit Range/Performance | Non-closed throttle position at idle. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P0122 | Throttle/Pedal Position Sensor A Circuit Low | TP sensor signal is less than Self-Test minimum of 0.17 volt (3.42%). | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P0123 | Throttle/Pedal Position Sensor A Circuit High | TP sensor signal is greater than Self-Test maximum of 4.65V (93%). | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P0124 | Throttle/Pedal Position Sensor A Intermittent | Powertrain control module (PCM) detected an intermittent concern with the TP sensor. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P0125 | Insufficient Coolant Temp For Closed Loop Fuel Control | ECT signal has not achieved required temperature level to enter closed loop operating conditions within a specified amount of time after starting engine. | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P0126 | Insufficient Coolant Temp For Stable Operation | ECT signal has not achieved required temperature level to enter closed loop operating conditions. | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P0128 | Coolant Thermostat (Coolant Temp Below Thermostat Regulating Temperature) | ECT signal has not achieved required temperature level to enter closed loop operating conditions within a specified amount of time after starting engine. | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P0130 | Oxygen Sensor (HO2S) Circuit (Bank 1, Sensor 1) | Front HO2S of Bank 1 is operating out of range. | See HEATED OXYGEN SENSOR (HO2S) . |
| P0131 | Oxygen Sensor (HO2S) Circuit Low Voltage (Bank 1, Sensor 1) | Front HO2S of Bank 1 generates a negative voltage. | See HEATED OXYGEN SENSOR (HO2S) . |
| P0132 | Oxygen Sensor (HO2S) Circuit High Voltage (Bank 1, Sensor 1) | Front HO2S of Bank 1 voltage greater than 1.5 volts. | See HEATED OXYGEN SENSOR (HO2S) OVER VOLTAGE . |
| P0133 | Oxygen Sensor (HO2S) Circuit Slow Response (Bank 1, Sensor 1) | The frequency and amplitude response rate of the upstream HO2S(s) is below calibrated window on Bank 1. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P0134 | Oxygen Sensor (HO2S) Circuit No Activity Detected (Bank 1, Sensor 1) | The HO2S is not supplying feedback information as required. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P0135 | Oxygen Sensor (HO2S) Heater Circuit (Bank 1, Sensor 1) | Front HO2S of Bank 1 heater circuit is open, shorted to ground, shorted to VPWR, or has low or high current draw. | See HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT . |
| P0136 | Oxygen Sensor (HO2S) Circuit (Bank 1, Sensor 2) (See P2270, P2271) | Output voltage of the rear HO2S (Bank 1) fails to meet the calibrated limits. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P0137 | Oxygen Sensor (HO2S) Circuit Low Voltage (Bank 1, Sensor 2) | Output voltage of the rear HO2S (Bank 1) fails to meet the calibrated limits. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P0138 | Oxygen Sensor (HO2S) Circuit High Voltage (Bank 1, Sensor 2) | The HO2S sensor signals are monitored for an over voltage fault. The code is set when HO2S signal voltage is 1.5 volts or greater. | See HEATED OXYGEN SENSOR (HO2S) OVER VOLTAGE . |
| P0139 | Oxygen Sensor (HO2S) Circuit Slow Response (Bank 1, Sensor 2) | The frequency and amplitude response rate of the downstream HO2S(s) is below calibrated window on Bank 1. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P0140 | Oxygen Sensor (HO2S) Circuit No Activity Detected (Bank 1, Sensor 2) | The HO2S is not supplying feedback information as required. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P0141 | Oxygen Sensor (HO2S) Heater Circuit (Bank 1, Sensor 2) | Rear HO2S of Bank 1 heater circuit is open, shorted to ground, shorted to VPWR, or has low or high current draw. | Address all other HO2S-related DTCs. |
| P0148 | Fuel Delivery Error | At least one bank lean at wide open throttle. | See TEST 4: FUEL DELIVERY SYSTEM . |
| P0150 | Oxygen Sensor (HO2S) Circuit (Bank 2, Sensor 1) | Concern has been registered with the front HO2S of bank 2. | Address all other HO2S-related DTCs. |
| P0151 | Oxygen Sensor (HO2S) Circuit Low Voltage (Bank 2, Sensor 1) | Front HO2S of Bank 2 generates a negative voltage. | See HEATED OXYGEN SENSOR (HO2S) . |
| P0152 | Oxygen Sensor (HO2S) Circuit High Voltage (Bank 2, Sensor 1) | The HO2S sensor signals are monitored for an over voltage fault. The code is set when HO2S signal voltage is 1.5 volts or greater. | See HEATED OXYGEN SENSOR (HO2S) OVER VOLTAGE . |
| P0153 | Oxygen Sensor (HO2S) Circuit Slow Response (Bank 2, Sensor 1) | The frequency and amplitude response rate of the upstream HO2S is below calibrated window on Bank 2. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P0154 | Oxygen Sensor (HO2S) Circuit No Activity Detected (Bank 2, Sensor 1) | The HO2S is not supplying feedback information as required. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P0155 | Oxygen Sensor (HO2S) Heater Circuit (Bank 2, Sensor 1) | Front HO2S of Bank 2 heater circuit is open, shorted to ground, shorted to VPWR, or has high low or high current draw. | Address all other HO2S-related DTCs. |
| P0156 | Oxygen Sensor (HO2S) Circuit (Bank 2, Sensor 2) (See P2272, P2273) | Output voltage of the rear HO2S (Bank 2) fails to meet the calibrated limits. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P0157 | Oxygen Sensor (HO2S) Circuit Low Voltage (Bank 2, Sensor 2 | Output voltage of the rear HO2S (Bank 2) fails to meet the calibrated limits. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P0158 | Oxygen Sensor (HO2S) Circuit High Voltage (Bank 2, Sensor 2) | Rear HO2S of Bank 2 voltage greater than 1.5 volts. | See HEATED OXYGEN SENSOR (HO2S) OVER VOLTAGE . |
| P0159 | Oxygen Sensor (HO2S) Circuit Slow Response (Bank 2, Sensor 2) | The frequency and amplitude response rate of the downstream HO2S(s) is below calibrated window on Bank 2. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P0160 | Oxygen Sensor (HO2S) Circuit No Activity Detected (Bank 2, Sensor 2 | HO2S is not supplying feedback information as required | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P0161 | Oxygen Sensor (HO2S) Heater Circuit (Bank 2, Sensor 2) | Rear HO2S of Bank 2 heater circuit is open, shorted to ground, shorted to VPWR, or has high low or high current draw. | Address all other HO2S-related DTCs. |
| P0170 | Fuel Trim (Bank 1) | Adaptive fuel tables have reached calibration limit (Bank 1). | See ADAPTIVE FUEL CONTROL . |
| P0171 | System Too Lean (Bank 1) | Fuel/air ratio is too lean (Bank 1). | See ADAPTIVE FUEL CONTROL . |
| P0172 | System Too Rich (Bank 1) | Fuel/air ratio is too rich (Bank 1). | See ADAPTIVE FUEL CONTROL . |
| P0173 | Fuel Trim (Bank 2) | The adaptive fuel tables have reached calibration limit (Bank 2). | See ADAPTIVE FUEL CONTROL . |
| P0174 | System Too Lean (Bank 2) | Fuel/air ratio is too lean (Bank 2). | See ADAPTIVE FUEL CONTROL . |
| P0175 | System Too Rich (Bank 2) | Fuel/air ratio is too rich (Bank 2). | See ADAPTIVE FUEL CONTROL . |
| P0180 | Fuel Temperature Sensor A Circuit | FRPT sensor voltage below calibrated limit. | See FUEL RAIL PRESSURE TEMPERATURE (FRPT) SENSOR . |
| P0181 | Fuel Temperature Sensor A Circuit Range/Performance | FRPT sensor voltage outside calibrated limit. | See FUEL RAIL PRESSURE TEMPERATURE (FRPT) SENSOR . |
| P0182 | Fuel Temperature Sensor A Circuit Low | FRPT sensor voltage below calibrated limit. | See FUEL RAIL PRESSURE TEMPERATURE (FRPT) SENSOR . |
| P0183 | Fuel Temperature Sensor A Circuit High | FRPT sensor voltage exceeds calibrated limit. | See FUEL RAIL PRESSURE TEMPERATURE (FRPT) SENSOR . |
| P0184 | Fuel Temperature Sensor A Circuit Intermittent | FRPT sensor voltage intermittent | See FUEL RAIL PRESSURE TEMPERATURE (FRPT) SENSOR . |
| P0185 | Fuel Temperature Sensor B Circuit | FRPT sensor voltage below calibrated limit. | See FUEL RAIL PRESSURE TEMPERATURE (FRPT) SENSOR . |
| P0186 | Fuel Temperature Sensor B Circuit Range/Performance | FRPT sensor voltage outside calibrated limit. | See FUEL RAIL PRESSURE TEMPERATURE (FRPT) SENSOR . |
| P0187 | Fuel Temperature Sensor B Circuit Low | FRPT sensor voltage below calibrated limit. | See FUEL RAIL PRESSURE TEMPERATURE (FRPT) SENSOR . |
| P0188 | Fuel Temperature Sensor B Circuit High | FRPT sensor voltage above calibrated limit. | See FUEL RAIL PRESSURE TEMPERATURE (FRPT) SENSOR . |
| P0189 | Fuel Temperature Sensor B Circuit Intermittent | FRPT sensor voltage intermittent | See FUEL RAIL PRESSURE TEMPERATURE (FRPT) SENSOR . |
| P0190 | Fuel Rail Pressure Sensor A Circuit | VREF voltage on FRPT circuit below 4 volts. | See FUEL RAIL PRESSURE TEMPERATURE (FRPT) SENSOR . |
| P0191 | Fuel Rail Pressure Sensor A Circuit Range/Performance | Indicated fuel pressure outside calibrated limits. | See FUEL RAIL PRESSURE TEMPERATURE (FRPT) SENSOR . |
| P0192 | Fuel Rail Pressure Sensor A Circuit Low. | FRPT sensor voltage below calibrated limit. | See FUEL RAIL PRESSURE TEMPERATURE (FRPT) SENSOR . |
| P0193 | Fuel Rail Pressure Sensor A Circuit High | FRPT sensor voltage exceeds calibrated limit. | See FUEL RAIL PRESSURE TEMPERATURE (FRPT) SENSOR . |
| P0194 | Fuel Rail Pressure Sensor A Circuit Intermittent/Erratic | FRPT sensor voltage exceeds calibrated limit. | See FUEL RAIL PRESSURE TEMPERATURE (FRPT) SENSOR . |
| P0201 | Injector Circuit / Open - Cylinder 1 | Fuel injector #1 does not operate correctly. | See FUEL INJECTOR MALFUNCTION . |
| P0202 | Injector Circuit / Open - Cylinder 2 | Fuel injector #2 does not operate correctly. | See FUEL INJECTOR MALFUNCTION . |
| P0203 | Injector Circuit / Open - Cylinder 3 | Fuel injector #3 does not operate correctly. | See FUEL INJECTOR MALFUNCTION . |
| P0204 | Injector Circuit / Open - Cylinder 4 | Fuel injector #4 does not operate correctly. | See FUEL INJECTOR MALFUNCTION . |
| P0205 | Injector Circuit / Open - Cylinder 5 | Fuel injector #5 does not operate correctly. | See FUEL INJECTOR MALFUNCTION . |
| P0206 | Injector Circuit / Open - Cylinder 6 | Fuel injector #6 does not operate correctly. | See FUEL INJECTOR MALFUNCTION . |
| P0217 | Engine Coolant Overtemperature Condition | Engine overheat condition was sensed by the ECT/CHT sensor. | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P0218 | Transaxle Fluid Overtemperature Condition | TFT indicates transaxle over temperature condition. | See TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR . |
| P0219 | Engine Overspeed Condition | Indicates the vehicle has been operated in a manner which caused the engine speed to exceed a calibration limit. The engine speed is continuously monitored and evaluated by the powertrain control module (PCM). The DTC is set when the rpm exceeds the calibrated limit set with in the PCM. | See ENGINE RPM/VEHICLE SPEED LIMITER . |
| P0221 | Throttle/Pedal Position Sensor/Switch B Circuit Range/Performance | The throttle position (TP) sensor circuit registered out of range in either the closed or wide open throttle positions. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P0222 | Throttle/Pedal Position Sensor/Switch B Circuit Low | The throttle position (TP) sensor circuit registered low voltage or an open circuit. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P0223 | Throttle/Pedal Position Sensor/Switch B Circuit High | The throttle position (TP) sensor circuit registered high voltage. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P0224 | Throttle/Pedal Position Sensor/Switch B Circuit Intermittent | Powertrain control module (PCM) detected an intermittent concern with the TP sensor. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P0230 | Fuel Pump Primary Circuit | The powertrain control module (PCM) has detected a concern with the fuel pump primary circuit | Address all other fuel pump-related DTCs. See FUEL PUMP (FP) PRIMARY OR SECONDARY CIRCUIT . |
| P0231 | Fuel Pump Secondary Circuit Low | Battery voltage not detected on the fuel pump monitor (FPM) circuit. | See FUEL PUMP (FP) PRIMARY OR SECONDARY CIRCUIT . |
| P0232 | Fuel Pump Secondary Circuit High | Battery voltage detected on the fuel pump monitor (FPM) circuit when the fuel pump is commanded off. | See FUEL PUMP (FP) PRIMARY OR SECONDARY CIRCUIT . |
| P0233 | Fuel Pump Secondary Circuit Intermittent | Intermittent concern detected on the fuel pump monitor circuit. | See FUEL PUMP (FP) PRIMARY OR SECONDARY CIRCUIT . |
| P0261 | Cylinder 1 Injector Circuit Low | A concern is detected in the fuel injector interface module in the primary (forward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P0262 | Cylinder 1 Injector Circuit High | A concern is detected in the fuel injector interface module in the primary (forward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P0264 | Cylinder 2 Injector Circuit Low | A concern is detected in the fuel injector interface module in the primary (forward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P0265 | Cylinder 2 Injector Circuit High | A concern is detected in the fuel injector interface module in the primary (forward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P0267 | Cylinder 3 Injector Circuit Low | A concern is detected in the fuel injector interface module in the primary (forward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P0268 | Cylinder 3 Injector Circuit High | A concern is detected in the fuel injector interface module in the primary (forward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P0270 | Cylinder 4 Injector Circuit Low | A concern is detected in the fuel injector interface module in the primary (forward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P0271 | Cylinder 4 Injector Circuit High | A concern is detected in the fuel injector interface module in the primary (forward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P0273 | Cylinder 5 Injector Circuit Low | A concern is detected in the fuel injector interface module in the primary (forward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P0274 | Cylinder 5 Injector Circuit High | A concern is detected in the fuel injector interface module in the primary (forward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P0276 | Cylinder 6 Injector Circuit Low | A concern is detected in the fuel injector interface module in the primary (forward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P0277 | Cylinder 6 Injector Circuit High | A concern is detected in the fuel injector interface module in the primary (forward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P0297 | Vehicle Overspeed Condition | The vehicle has been operated in a manner which caused the engine or vehicle to exceed a calibration limit. | See ENGINE RPM/VEHICLE SPEED LIMITER . |
| P0298 | Engine Oil Overtemperature Condition | Oil protection strategy in the powertrain control module (PCM) has been activated. PCM uses an oil algorithm to infer actual oil temperature. | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P0300 | Random Misfire Detected | Multiple cylinders misfiring, or cannot identify cylinder due to camshaft position sensor failure. | See MISFIRE DETECTION MONITOR . |
| P0301 | Cylinder 1 Misfire Detected | Cylinder #1 misfiring. | See MISFIRE DETECTION MONITOR . |
| P0302 | Cylinder 2 Misfire Detected | Cylinder #2 misfiring. | See MISFIRE DETECTION MONITOR . |
| P0303 | Cylinder 3 Misfire Detected | Cylinder #3 misfiring. | See MISFIRE DETECTION MONITOR . |
| P0304 | Cylinder 4 Misfire Detected | Cylinder #4 misfiring. | See MISFIRE DETECTION MONITOR . |
| P0305 | Cylinder 5 Misfire Detected | Cylinder #5 misfiring. | See MISFIRE DETECTION MONITOR . |
| P0306 | Cylinder 6 Misfire Detected | Cylinder #6 misfiring. | See MISFIRE DETECTION MONITOR . |
| P0315 | Crankshaft Position System Variation Not Learned | Powertrain control module (PCM) is unable to learn Crankshaft Pulse Wheel tooth spacing (exceeded the allowable correction tolerances). | See MISFIRE DETECTION MONITOR . |
| P0316 | Misfire Detected On Startup (First 1000 Revolutions) | Misfire occurred in the first 1000 engine revolutions. | See MISFIRE DETECTION MONITOR . |
| P0320 | Ignition/Distributor Engine Speed Input Circuit | Two successive erratic Profile Ignition Pickup (PIP) pulses occurred resulting in possible engine miss or stall. | See CRANKSHAFT POSITION (CKP) SENSOR MALFUNCTION . |
| P0321 | Ignition/Distributor Engine Speed Input Circuit Range/Performance | Profile Ignition Pickup (PIP) pulses out of range. | See CRANKSHAFT POSITION (CKP) SENSOR MALFUNCTION . |
| P0322 | Ignition/Distributor Engine Speed Input Circuit No Signal | Profile Ignition Pickup (PIP) pulses missing. | See CRANKSHAFT POSITION (CKP) SENSOR MALFUNCTION . |
| P0323 | Ignition/Distributor Engine Speed Input Circuit Intermittent | Profile Ignition Pickup (PIP) pulses intermittent. | See CRANKSHAFT POSITION (CKP) SENSOR MALFUNCTION . |
| P0325 | Knock Sensor 1 Circuit (Bank 1) | Knock sensor circuit malfunction. | See KNOCK SENSOR MALFUNCTION . |
| P0326 | Knock Sensor 1 Circuit Range/Performance (Bank 1) | Knock sensor has detected vibrations (voltage generated based on this vibration) upon an increase and decrease in engine rpm that is outside a calibrated level. | See KNOCK SENSOR MALFUNCTION . |
| P0327 | Knock Sensor 1 Circuit Low (Bank 1) | Knock sensor has detected vibrations (voltage generated based on this vibration) upon an increase and decrease in engine rpm that is below a calibrated level. | See KNOCK SENSOR MALFUNCTION . |
| P0328 | Knock Sensor 1 Circuit High (Bank 1) | Knock sensor has detected vibrations (voltage generated based on this vibration) upon an increase and decrease in engine rpm that is above the calibrated level. | See KNOCK SENSOR MALFUNCTION . |
| P0329 | Knock Sensor 1 Circuit Intermittent (Bank 1) | Knock sensor has detected vibrations (voltage generated based on this vibration) upon an increase and decrease in engine rpm that is intermittent. | See KNOCK SENSOR MALFUNCTION . |
| P0340 | Camshaft Position Sensor A Circuit (Bank 1 or single sensor) | Camshaft Position (CMP) sensor circuit failure. | See CAMSHAFT POSITION SENSOR (CMP) MALFUNCTION . |
| P0344 | Camshaft Position Sensor A Circuit Intermittent (Bank 1 or single sensor) | Camshaft Position (CMP) sensor circuit failure. | See CAMSHAFT POSITION SENSOR (CMP) MALFUNCTION . |
| P0350 | Ignition Coil Primary/Secondary Circuit | Powertrain control module (PCM) did not receive a valid Ignition Diagnostic Monitor (IDM) pulse signal, which indicates that the primary side of the coil has failed, from the ignition module (integrated in the PCM). This is caused by an Ignition coil primary/secondary circuit malfunction. | See IGNITION COIL PRIMARY CIRCUIT MALFUNCTION . |
| P0351 | Ignition Coil A Primary/Secondary Circuit | Powertrain control module (PCM) did not receive a valid Ignition Diagnostic Monitor (IDM) pulse signal, which indicates that the primary side of the coil has failed from the ignition module (integrated in the PCM). This is caused by an ignition coil failure. | See INTEGRATED IGNITION COIL 1, 2, 3, 4, 5, OR 6 FAILURE . |
| P0352 | Ignition Coil B Primary/Secondary Circuit | Powertrain control module (PCM) did not receive a valid Ignition Diagnostic Monitor (IDM) pulse signal, which indicates that the primary side of the coil has failed from the ignition module (integrated in the PCM). This is caused by an ignition coil failure. | See INTEGRATED IGNITION COIL 1, 2, 3, 4, 5, OR 6 FAILURE . |
| P0353 | Ignition Coil C Primary/Secondary Circuit | Powertrain control module (PCM) did not receive a valid Ignition Diagnostic Monitor (IDM) pulse signal, which indicates that the primary side of the coil has failed from the ignition module (integrated in the PCM). This is caused by an ignition coil failure. | See INTEGRATED IGNITION COIL 1, 2, 3, 4, 5, OR 6 FAILURE . |
| P0354 | Ignition Coil D Primary/Secondary Circuit | Powertrain control module (PCM) did not receive a valid Ignition Diagnostic Monitor (IDM) pulse signal, which indicates that the primary side of the coil has failed from the ignition module (integrated in the PCM). This is caused by an ignition coil failure. | See INTEGRATED IGNITION COIL 1, 2, 3, 4, 5, OR 6 FAILURE . |
| P0355 | Ignition Coil E Primary/Secondary Circuit | Powertrain control module (PCM) did not receive a valid Ignition Diagnostic Monitor (IDM) pulse signal, which indicates that the primary side of the coil has failed from the ignition module (integrated in the PCM). This is caused by an ignition coil failure. | See INTEGRATED IGNITION COIL 1, 2, 3, 4, 5, OR 6 FAILURE . |
| P0356 | Ignition Coil F Primary/Secondary Circuit | Powertrain control module (PCM) did not receive a valid Ignition Diagnostic Monitor (IDM) pulse signal, which indicates that the primary side of the coil has failed from the ignition module (integrated in the PCM). This is caused by an ignition coil failure. | See INTEGRATED IGNITION COIL 1, 2, 3, 4, 5, OR 6 FAILURE . |
| P0400 | Exhaust Gas Recirculation Flow | Self-Test has detected EGR flow is outside calibrated limits. | See EGR SYSTEM MALFUNCTION - 3.0L or EGR SYSTEM MALFUNCTION - 2.3L . |
| P0401 | Exhaust Gas Recirculation Flow Insufficient Detected | Self-Test has detected Insufficient EGR flow. | See EGR SYSTEM MALFUNCTION - 3.0L or EGR SYSTEM MALFUNCTION - 2.3L . |
| P0402 | Exhaust Gas Recirculation Flow Excessive Detected | Self-Test has detected DPFEGR signal at idle is greater than at KOEO by a calibrated amount. | See EGR SYSTEM MALFUNCTION - 3.0L . |
| P0403 | Exhaust Gas Recirculation Control Circuit | Self-test has detected an electrical malfunction in EGRVR circuit. | See EGR SYSTEM MALFUNCTION - 3.0L or EGR SYSTEM MALFUNCTION - 2.3L . |
| P0404 | Exhaust Gas Recirculation Control Circuit Range/Performance | Powertrain control module (PCM) has detected the EGR system operating out of expected parameters. | See EGR SYSTEM MALFUNCTION - 3.0L or EGR SYSTEM MALFUNCTION - 2.3L . |
| P0405 | Exhaust Gas Recirculation Sensor A Circuit Low | The average voltage of the DPFEGR SIG circuit input is below minimum (0.2 V). | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P0406 | Exhaust Gas Recirculation Sensor A Circuit High | The average voltage of the DPFEGR SIG circuit input is above maximum (4.5V). | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P0420 | Catalyst System Efficiency Below Threshold (Bank 1) | Bank 1 catalyst system efficiency is below acceptable threshold. | See CATALYST EFFICIENCY MONITOR MALFUNCTION . |
| P0421 | Warm Up Catalyst Efficiency Below Threshold (Bank 1) | Bank 1 catalyst system efficiency is below acceptable threshold. | See CATALYST EFFICIENCY MONITOR MALFUNCTION . |
| P0430 | Catalyst System Efficiency Below Threshold (Bank 2) | Bank 2 catalyst system efficiency is below acceptable threshold. | See CATALYST EFFICIENCY MONITOR MALFUNCTION . |
| P0431 | Warm Up Catalyst Efficiency Below Threshold (Bank 2) | Bank 2 catalyst system efficiency is below acceptable threshold. | See CATALYST EFFICIENCY MONITOR MALFUNCTION . |
| P0440 | Evaporative Emission (EVAP) System | The powertrain control module (PCM) has detected a concern with the EVAP system. | See EVAPORATIVE EMISSION SYSTEM LEAK TEST . |
| P0441 | Evaporative Emission (EVAP) System Incorrect Purge Flow | The powertrain control module (PCM) has detected a concern with the EVAP system. | See EVAPORATIVE EMISSION (EVAP) CANISTER PURGE SOLENOID MALFUNCTION . |
| P0442 | Evaporative Emission (EVAP) System Leak Detected (small leak) | A small leak has been detected in the EVAP system. | See EVAPORATIVE EMISSION (EVAP) MONITOR AND SYSTEM MALFUNCTION . |
| P0443 | Evaporative Emission (EVAP) System Purge Control Valve Circuit | Signal moved outside the minimum or maximum allowable calibrated parameters for a specified purge duty cycle by PCM command. | See EVAPORATIVE EMISSION (EVAP) CANISTER PURGE SOLENOID MALFUNCTION . |
| P0444 | Evaporative Emission (EVAP) System Purge Control Valve Circuit Open | Signal is higher than the maximum allowable calibrated parameter. | See EVAPORATIVE EMISSION (EVAP) CANISTER PURGE SOLENOID MALFUNCTION . |
| P0445 | Evaporative Emission (EVAP) System Purge - Control Valve Circuit Shorted | Signal is below the minimum allowable calibrated parameter. | See EVAPORATIVE EMISSION (EVAP) CANISTER PURGE SOLENOID MALFUNCTION . |
| P0446 | Evaporative Emission (EVAP) System Vent Control Circuit | Signal moved outside the minimum or maximum allowable calibrated parameters for a specified purge duty cycle by powertrain control module (PCM) command. | See CANISTER VENT (CV) SOLENOID MALFUNCTION . |
| P0450 | Evaporative Emission (EVAP) System Pressure Sensor/Switch | Self-Test has detected an FTP circuit input out of range. | See FUEL TANK PRESSURE (FTP) SENSOR MALFUNCTION . |
| P0451 | Evaporative Emission (EVAP) System Pressure Sensor/Switch Range/Performance | Fuel tank pressure changes greater than 14 in-H2 O in 0.10 seconds. | If only DTC P0451 and/or DTC P0461 are present, see TEST 3: INTERMITTENT . Otherwise, repair all other DTCs present and disregard DTC P0451 and/or DTC P0461. |
| P0452 | Evaporative Emission (EVAP) System Pressure Sensor/Switch Low | Self-test has detected an FTP circuit input below minimum. | See FUEL TANK PRESSURE (FTP) SENSOR MALFUNCTION . |
| P0453 | Evaporative Emission (EVAP) System Pressure Sensor/Switch High | Self-test has indicated an FTP circuit input above maximum. | See FUEL TANK PRESSURE (FTP) SENSOR MALFUNCTION . |
| P0454 | Evaporative Emission (EVAP) System Pressure Sensor/Switch Intermittent | Intermittent open or short in the FTP sensor circuit | See EVAP SYSTEM MALFUNCTION . |
| P0455 | Evaporative Emission (EVAP) System Leak Detected (gross leak/no flow) | A substantial leak or blockage has been detected in the EVAP system when there is -7.0 in-H2 O (-1.74kpa) or less vacuum for 30 seconds evaluation time. | See EVAPORATIVE EMISSION (EVAP) SYSTEM MALFUNCTION . |
| P0456 | Evaporative Emission (EVAP) System Leak Detected (very small leak) | A small leak has been detected in the EVAP system. | See EVAPORATIVE EMISSION (EVAP) SYSTEM MALFUNCTION . |
| P0457 | Evaporative Emission (EVAP) System Leak Detected (fuel cap loose/off) | Initial vacuum could not be achieved after a refueling event and the purge vapor flow is excessive (gross leak). | See EVAPORATIVE EMISSION (EVAP) SYSTEM MALFUNCTION . |
| P0460 | Fuel Level Sensor A Circuit | Fuel level input (FLI) signal moves outside the minimum or maximum allowable calibrated parameters for a specified fuel fill percentage in the fuel tank. | See PINPOINT TEST 3: INCORRECT FUEL GAUGE INDICATION . |
| P0461 | Fuel Level Sensor A Circuit Range/Performance | Fuel level input noisy. | If only DTC P0451 and/or DTC P0461 are present, see TEST 3: INTERMITTENT . Otherwise, repair all other DTCs present and disregard DTC P0451 and/or DTC P0461. |
| P0462 | Fuel Level Sensor A Circuit Low | Fuel level input below calibrated minimum value. | See PINPOINT TEST 3: INCORRECT FUEL GAUGE INDICATION . |
| P0463 | Fuel Level Sensor A Circuit High | Fuel level input above calibrated maximum value. | See PINPOINT TEST 3: INCORRECT FUEL GAUGE INDICATION . |
| P0464 | Fuel Level Sensor A Circuit Intermittent | Fuel level input intermittent. | See TEST 3: INTERMITTENT . |
| P0480 | Fan 1 Control Circuit | Excessive current draw is detected on the Low Fan Control (LFC) circuit when the powertrain control module (PCM) grounds the circuit or with the LFC circuit not grounded by the PCM, voltage is not detected on the LFC circuit (the PCM expects to detect VPWR voltage coming through the low speed FC relay coil to the LFC circuit). | See COOLING FAN MALFUNCTION . |
| P0481 | Fan 2 Control Circuit | Excessive current draw is detected on the Low Fan Control (LFC) circuit when the powertrain control module (PCM) grounds the circuit or with the LFC circuit not grounded by the PCM, voltage is not detected on the LFC circuit (the PCM expects to detect VPWR voltage coming through the low speed FC relay coil to the LFC circuit). | See COOLING FAN MALFUNCTION . |
| P0482 | Fan 3 Control Circuit | Medium cooling fan control primary circuit failure. | See COOLING FAN MALFUNCTION . |
| P0483 | Fan Performance | The powertrain control module (PCM) has detected a concern with the cooling fan system. | See COOLING FAN MALFUNCTION . |
| P0484 | Fan Current | Cooling fan control primary circuit failure. | See COOLING FAN MALFUNCTION . |
| P0485 | Fan Power/Ground Circuit | Cooling fan control primary circuit failure. | See COOLING FAN MALFUNCTION . |
| P0489 | Exhaust Gas Recirculation Control Circuit Low | The DPFEGR sensor pressure electrical concern. | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P0490 | Exhaust Gas Recirculation Control Circuit High | The DPFEGR sensor pressure electrical concern. | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P0496 | Evaporative Emission (EVAP) System High Purge Flow | Excessive canister purge flow has been detected. | See EVAPORATIVE EMISSION (EVAP) SYSTEM MALFUNCTION . |
| P0497 | Evaporative Emission (EVAP) System Low Purge Flow | Inadequate canister purge flow has been detected. | See EVAPORATIVE EMISSION (EVAP) SYSTEM MALFUNCTION . |
| P0498 | Evaporative Emission (EVAP) System Vent Control Circuit Low | Powertrain control module (PCM) has detected a concern with the canister vent solenoid. | See PINPOINT TEST 3: UNABLE TO REFUEL (ORVR) . |
| P0499 | Evaporative Emission (EVAP) System Vent Control Circuit High | Powertrain control module (PCM) has detected a concern with the canister vent solenoid. | See PINPOINT TEST 3: UNABLE TO REFUEL (ORVR) . |
| P0500 | Vehicle Speed Sensor A | Powertrain control module (PCM) detected an error in the vehicle speed information received from the VSS Sensor. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P0501 | Vehicle Speed Sensor A Range/Performance | Powertrain control module (PCM) detected an error in the vehicle speed information received from the VSS Sensor. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P0502 | Vehicle Speed Sensor A Circuit Low | Powertrain control module (PCM) detected an error in the vehicle speed information received from the VSS Sensor. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P0503 | Vehicle Speed Sensor A Intermittent/Erratic/High | Poor or noisy VSS performance. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P0505 | Idle Air Control (IAC) System | Desired RPM could not be reached or controlled during KOEO Self-Test. | See IDLE AIR CONTROL (IAC) VALVE ASSEMBLY MALFUNCTION . |
| P0506 | Idle Air Control (IAC) System RPM Lower Than Expected | Desired RPM could not be reached or controlled during KOEO Self-Test. | See IDLE AIR CONTROL (IAC) VALVE ASSEMBLY MALFUNCTION . |
| P0507 | Idle Air Control (I AC) System RPM Higher Than Expected | Engine idle speed is greater than desired rpm. | See IDLE AIR CONTROL (IAC) VALVE ASSEMBLY MALFUNCTION . |
| P0510 | Closed Throttle Position Switch | Throttle position sensor not operating as expected. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P0511 | Idle Air Control (IAC) Circuit | Powertrain control module (PCM) detects electrical load failure on IAC output circuit. | See IDLE AIR CONTROL (IAC) VALVE ASSEMBLY MALFUNCTION . |
| P0518 | Idle Air Control (IAC) Circuit Intermittent | Powertrain control module (PCM) detects an intermittent electrical failure on the IAC output circuit. | See IDLE AIR CONTROL (IAC) VALVE ASSEMBLY MALFUNCTION . |
| P0519 | Idle Air Control (IAC) Circuit System Performance | IAC operating out of range. | See IDLE AIR CONTROL (IAC) VALVE ASSEMBLY MALFUNCTION . |
| P0525 | Cruise Control Servo Control Circuit Range/Performance | Speed control servo operating out of expected range. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0530 | A/C Refrigerant Pressure Sensor A Circuit | A/C refrigerant pressure sensor operating out of range. | See A/C PRESSURE SENSOR (ACP) MALFUNCTION . |
| P0531 | A/C Refrigerant Pressure Sensor A Circuit Range/Performance | A/C refrigerant pressure sensor operating out of range. | See A/C PRESSURE SENSOR (ACP) MALFUNCTION . |
| P0532 | A/C Refrigerant Pressure Sensor A Circuit Low | ACP sensor voltage below calibrated limit. | See A/C PRESSURE SENSOR (ACP) MALFUNCTION . |
| P0533 | A/C Refrigerant Pressure Sensor A Circuit High | ACP sensor voltage above calibrated limit. | See A/C PRESSURE SENSOR (ACP) MALFUNCTION . |
| P0534 | A/C Refrigerant Charge Loss | A/C compressor clutch cycling too frequently. | See SYMPTOM TROUBLESHOOTING CHART - AIR CONDITIONING (A/C) . |
| P0550 | Power Steering Pressure (PSP) Sensor/Switch Circuit | Powertrain control module (PCM) detects a concern with the power steering pressure sensor | See POWER STEERING PRESSURE (PSP) SWITCH MALFUNCTION . |
| P0551 | Power Steering Pressure (PSP) Sensor/Switch Circuit Range/Performance | Power steering pressure sensor out of range. | See POWER STEERING PRESSURE (PSP) SWITCH MALFUNCTION . |
| P0552. | Power Steering Pressure (PSP) Sensor/Switch Circuit Low | PSP signal is open or shorted to ground. | See POWER STEERING PRESSURE (PSP) SWITCH MALFUNCTION . |
| P0553 | Power Steering Pressure (PSP) Sensor/Switch Circuit High | PSP signal is shorted to power. | See POWER STEERING PRESSURE (PSP) SWITCH MALFUNCTION . |
| P0554 | Power Steering Pressure (PSP) Sensor/Switch Circuit Intermittent | Intermittent concern with PSP signal. | See POWER STEERING PRESSURE (PSP) SWITCH MALFUNCTION . |
| P0564 | Cruise Control Multi-Function Input A Circuit | Powertrain control module (PCM) detects a concern with the cruise control input circuit(s). | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0565 | Cruise Control ON Signal | Powertrain control module (PCM) detects a concern with the cruise control ON circuit. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0566 | Cruise Control OFF Signal | Powertrain control module (PCM) detects a concern with the cruise control OFF circuit. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0567 | Cruise Control RESUME Signal | Powertrain control module (PCM) detects a concern with the cruise control RESUME circuit. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0568 | Cruise Control SET Signal | Powertrain control module (PCM) detects a concern with the cruise control SET circuit. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0569 | Cruise Control COAST Signal | Powertrain control module (PCM) detects a concern with the cruise control COAST circuit. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0570 | Cruise Control ACCEL Signal | Powertrain control module (PCM) detects a concern with the cruise control ACCEL circuit. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0574 | Cruise Control System - Vehicle Speed Too High | Vehicle speed above set parameter. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0575 | Cruise Control Input Circuit | Cruise control input circuit out of range. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0576 | Cruise Control Input Circuit Low | Cruise control input circuit voltage below minimum parameter. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0577 | Cruise Control Input Circuit High | Cruise control input circuit voltage above maximum parameter. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0578 | Cruise Control Multi-Function Input A Circuit Stuck | Powertrain control module (PCM) detects a concern with the cruise control input circuit(s). | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0579 | Cruise Control Multi-Function Input A Circuit Range/Performance | Cruise control input circuit(s) out of range. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0580 | Cruise Control Multi-Function Input A Circuit Low | Cruise control input circuit below minimum set parameter. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0581 | Cruise Control Multi-Function Input A Circuit High | Cruise control input circuit above maximum set parameter. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0594 | Cruise Control Servo Control Circuit / Open | Cruise control servo circuit high resistance or open. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0595 | Cruise Control Servo Control Circuit Low. | Cruise control servo circuit voltage below expected parameter. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0596 | Cruise Control Servo Control Circuit High | Cruise control servo circuit voltage higher than expected parameter. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P0600 | Serial Communication Link | Network communication. | See COMMUNICATIONS NETWORK TROUBLESHOOTING . |
| P0601 | Internal Control Module Memory Check Sum Error | Internal powertrain control module (PCM) error. | See POWERTRAIN CONTROL MODULE (PCM) MALFUNCTION . |
| P0602 | Powertrain control module (PCM) Programming Error | Control module programming error. | See MODULE CONFIGURATION . |
| P0603 | Internal Control Module Keep Alive Memory (KAM) Error | The powertrain control module (PCM) has experienced a power interrupt in the Keep Alive Power (KAPWR) circuit or an internal memory test failure. However there are external items that can cause the DTC. | See POWERTRAIN CONTROL MODULE (PCM) MALFUNCTION . |
| P0604 | Internal Control Module Random Access Memory (RAM) Error | The powertrain control module (PCM) has experienced a power interrupt in the Keep Alive Power (KAPWR) circuit or an internal memory test failure. However there are external items that can cause the DTC. | See POWERTRAIN CONTROL MODULE (PCM) MALFUNCTION . |
| P0605 | Internal Control Module Read Only Memory (ROM) Error | The powertrain control module (PCM) ROM has been corrupted. | See POWERTRAIN CONTROL MODULE (PCM) MALFUNCTION . |
| P0606 | ECM / PCM Processor | Powertrain control module (PCM) internal communications error. | See POWERTRAIN CONTROL MODULE (PCM) MALFUNCTION . |
| P0607 | Control Module Performance | Powertrain control module (PCM) performance. | See POWERTRAIN CONTROL MODULE (PCM) MALFUNCTION . |
| P0610 | Control Module Vehicle Options Error | Control Module Performance | See POWERTRAIN CONTROL MODULE (PCM) MALFUNCTION . |
| P0620 | Generator Control Circuit | Circuit fault on the I-Line to generator/regulator. | See GENERATOR/REGULATOR SYSTEM MALFUNCTION . |
| P0622 | Generator Field Terminal Circuit | The Generator Load Input (GLI) is not within a calibrated limit for a calibrated amount of time. | See GENERATOR/REGULATOR SYSTEM MALFUNCTION . |
| P0625 | Generator Field Terminal Circuit Low | The Generator Load Input (GLI) is below a calibrated limit for a calibrated amount of time. | See GENERATOR/REGULATOR SYSTEM MALFUNCTION . |
| P0626 | Generator Field Terminal Circuit High | The Generator Load Input (GLI) is above a calibrated limit for a calibrated amount of time. | See GENERATOR/REGULATOR SYSTEM MALFUNCTION . |
| P0630 | VIN Not Programmed or Incompatible - ECM/PCM | Powertrain control module (PCM) programming error. | See POWERTRAIN CONTROL MODULE (PCM) MALFUNCTION . |
| P0632 | Odometer Not Programmed - ECM/PCM | PCM programming error. | See POWERTRAIN CONTROL MODULE (PCM) MALFUNCTION . |
| P0633 | Immobilizer Key Not Programmed - ECM/PCM | PCM programming error. | See POWERTRAIN CONTROL MODULE (PCM) MALFUNCTION . |
| P0638 | Throttle Actuator Control Range/Performance - Bank 1 | IMTV system. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P0639 | Throttle Actuator Control Range/Performance - Bank 2 | IMTV system. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P0645 | A/C Clutch Relay Control Circuit | Excessive current draw is detected on the ACCR circuit when powertrain control module (PCM) grounds the circuit or voltage is not detected on the ACCR circuit when the circuit is not grounded by the PCM. | See A/C CLUTCH RELAY (ACCR) MALFUNCTION . |
| P0646 | A/C Clutch Relay Control Circuit Low | A/C clutch relay control circuit voltage lower than minimum parameter. | See A/C CLUTCH RELAY (ACCR) MALFUNCTION . |
| P0647 | A/C Clutch Relay Control Circuit High | A/C clutch relay control circuit voltage high. | See A/C CLUTCH RELAY (ACCR) MALFUNCTION . |
| P0660 | Intake Manifold Tuning Valve Control Circuit / Open - Bank 1 | IMTV control circuit voltage outside of calibrated limits. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P0661 | Intake Manifold Tuning Valve Control Circuit Low - Bank 1 | IMTV control circuit voltage outside of calibrated limits. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P0662 | Intake Manifold Tuning Valve Control Circuit High - Bank 1 | IMTV control circuit voltage outside of calibrated limits. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P0663 | Intake Manifold Tuning Valve Control Circuit / Open - Bank 2 | IMTV control circuit voltage outside of calibrated limits. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P0664 | Intake Manifold Tuning Valve Control Circuit Low - Bank 2 | IMTV control circuit voltage outside of calibrated limits. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P0665 | Intake Manifold Tuning Valve Control Circuit High - Bank 2 | IMTV control circuit voltage outside of calibrated limits. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P0668 | PCM / ECM / TCM Internal Temperature Sensor Circuit Low | PCM programming error. | See POWERTRAIN CONTROL MODULE (PCM) MALFUNCTION . |
| P0669 | PCM / ECM / TCM Internal Temperature Sensor Circuit High | PCM programming error. | See POWERTRAIN CONTROL MODULE (PCM) MALFUNCTION . |
| P0703 | Brake Switch B Input Circuit | Powertrain control module (PCM) did not receive a BPP input. | See BRAKE PEDAL POSITION (BPP) SWITCH MALFUNCTION . |
| P0704 | Clutch Switch Input Circuit | A malfunction of the CPP Switch has been detected. | See CLUTCH PEDAL POSITION (CPP) SWITCH MALFUNCTION . |
| P0705 | Transaxle Range Sensor A Circuit (PRNDL Input) | TR signal is not in PARK during KOEO Self-Test. | See TRANSAXLE RANGE (TR) SENSOR . |
| P0706 | Transaxle Range Sensor A Circuit Range/Performance | TR sensor is out of range. | See TRANSAXLE RANGE (TR) SENSOR . |
| P0707 | Transaxle Range Sensor A Circuit Low | TR circuit failure. | See TRANSAXLE RANGE (TR) SENSOR . |
| P0708 | Transaxle Range Sensor A Circuit High | TR sensor circuit TR3A open. | See TRANSAXLE RANGE (TR) SENSOR . |
| P0709 | Transaxle Range Sensor A Circuit Intermittent | TR circuit failure. | See TRANSAXLE RANGE (TR) SENSOR . |
| P0710 | Transaxle Fluid Temperature Sensor A Circuit | TFT sensor in range failure. | See TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR . |
| P0711 | Transaxle Fluid Temperature Sensor A Circuit Range/Performance | TFT sensor in range failure. | See TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR . |
| P0712 | Transaxle Fluid Temperature Sensor A Circuit Low | Voltage drop across TFT sensor exceeds scale set for temperature of 150°C (302°F). | See TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR . |
| P0713 | Transaxle Fluid Temperature Sensor A Circuit High | Voltage drop across TFT signal exceeds scale set for temperature of -40°C (-40°F). | See TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR : |
| P0714 | Transaxle Fluid Temperature Sensor A Circuit Intermittent | TFT sensor in range failure. | See TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR . |
| P0715 | Turbine/Input Shaft Speed Sensor A Circuit | Powertrain control module (PCM) detected a loss of TSS signal during operation. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P0716 | Turbine/Input Shaft Speed Sensor A Circuit Range/Performance | Powertrain control module (PCM) detected TSS signal out of range. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P0717 | Turbine/Input Shaft Speed Sensor A Circuit No Signal | Powertrain control module (PCM) detected no TSS signal. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P0718 | Turbine/Input Shaft Speed Sensor A Circuit Intermittent | Powertrain control module (PCM) detected an erratic TSS signal. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P0719 | Brake Switch B Circuit Low | Brake switch circuit low voltage. | See BRAKE PEDAL POSITION (BPP) SWITCH MALFUNCTION . |
| P0720 | Output Shaft Speed Sensor Circuit | Powertrain control module (PCM) detected a loss of OSS signal during operation. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P0721 | Output Shaft Speed Sensor Circuit Range/Performance | Powertrain control module (PCM) detected an erratic OSS signal. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P0722 | Output Shaft Speed Sensor Circuit No Signal | Powertrain control module (PCM) has detected an intermittent OSS signal. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P0723 | Output Shaft Speed Sensor Circuit Intermittent | OSS signal irregular or interrupted. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P0724 | Brake Switch B Circuit High | Brake switch circuit voltage high. | See BRAKE PEDAL POSITION (BPP) SWITCH MALFUNCTION . |
| P0725 | Engine Speed Input Circuit | OSS signal intermittent. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P0726 | Engine Speed Input Circuit Range/Performance | OSS out of range. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P0727 | Engine Speed Input Circuit No Signal | OSS output voltage low. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P0728 | Engine Speed Input Circuit Intermittent | OSS signal intermittent. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P0730 | Incorrect Gear Ratio | First gear failure. | See SHIFT SOLENOIDS . |
| P0731 | Gear 1 Incorrect Ratio | First gear error. | See SHIFT SOLENOIDS . |
| P0732 | Gear 2 Incorrect Ratio | Second gear error. | See SHIFT SOLENOIDS . |
| P0733 | Gear 3 Incorrect Ratio | Third gear error. | See SHIFT SOLENOIDS . |
| P0734 | Gear 4 Incorrect Ratio | Fourth gear error. | See SHIFT SOLENOIDS . |
| P0740 | Torque Converter Clutch (TCC) Solenoid Circuit / Open | Torque converter clutch solenoid circuit failure during self-test. | See SHIFT SOLENOIDS . |
| P0741 | Torque Converter Clutch (TCC) Solenoid Circuit Performance Or Stuck Off. | Excessive slip detected. | See SHIFT SOLENOIDS . |
| P0742 | Torque Converter Clutch (TCC) Solenoid Circuit Stuck On | TCC solenoid energized | See SHIFT SOLENOIDS . |
| P0743 | Torque Converter Clutch (TCC) Solenoid Circuit Electrical | TCC solenoid circuit failure. | See SHIFT SOLENOIDS . |
| P0744 | Torque Converter Clutch (TCC) Solenoid Circuit Intermittent | TCC fails intermittently | See SHIFT SOLENOIDS . |
| P0745 | Pressure Control Solenoid A | SS1 solenoid circuit failure, open or shorted. | See ELECTRONIC PRESSURE CONTROL (EPC) SOLENOID . |
| P0746 | Pressure Control Solenoid A Performance or Stuck Off | SS1 solenoid circuit failure, open or shorted. | See ELECTRONIC PRESSURE CONTROL (EPC) SOLENOID . |
| P0747 | Pressure Control Solenoid A Stuck On | SS1 solenoid circuit failure, stuck on. | See ELECTRONIC PRESSURE CONTROL (EPC) SOLENOID . |
| P0748 | Pressure Control Solenoid A Electrical | EPC solenoid circuit failure, shorted to ground. | See ELECTRONIC PRESSURE CONTROL (EPC) SOLENOID . |
| P0749 | Pressure Control Solenoid A Intermittent | EPC solenoid circuit failure, intermittent. | See ELECTRONIC PRESSURE CONTROL (EPC) SOLENOID . |
| P0750 | Shift Solenoid A | SS1 solenoid circuit failure. | See SHIFT SOLENOIDS . |
| P0751 | Shift Solenoid A Performance or Stuck Off | Shift solenoid circuit failure. | See SHIFT SOLENOIDS . |
| P0752 | Shift Solenoid A Stuck On | SS1 solenoid circuit failure, open or shorted. | See SHIFT SOLENOIDS . |
| P0753 | Shift Solenoid A Electrical | SS1 solenoid circuit failure. | See SHIFT SOLENOIDS . |
| P0754 | Shift Solenoid A Intermittent | SS1 solenoid circuit failure. | See SHIFT SOLENOIDS . |
| P0755 | Shift Solenoid B | SS2 solenoid circuit failure. | See SHIFT SOLENOIDS . |
| P0756 | Shift Solenoid B Performance or Stuck Off | SS2 function failure. | See SHIFT SOLENOIDS . |
| P0757 | Shift Solenoid B Stuck On | SS2 function failure. | See SHIFT SOLENOIDS . |
| P0758 | Shift Solenoid B Electrical | SS2 solenoid circuit failure. | See SHIFT SOLENOIDS . |
| P0759 | Shift Solenoid B Intermittent | SS2 solenoid circuit failure. | See SHIFT SOLENOIDS . |
| P0775 | Pressure Control Solenoid B | 3-2T/CCS solenoid circuit failure detected. | See TIMING/COAST CLUTCH (2-3T/CCS) SOLENOID . |
| P0776 | Pressure Control Solenoid B Performance or Stuck Off | 3-2T/CCS solenoid circuit failure detected. | See TIMING/COAST CLUTCH (2-3T/CCS) SOLENOID . |
| P0777 | Pressure Control Solenoid B Stuck On | 3-2T/CCS solenoid circuit failure detected. | See TIMING/COAST CLUTCH (2-3T/CCS) SOLENOID . |
| P0778 | Pressure Control Solenoid B Electrical | 3-2T/CCS solenoid circuit failure(s) detected. | See TIMING/COAST CLUTCH (2-3T/CCS) SOLENOID . |
| P0779 | Pressure Control Solenoid B Intermittent | 3-2T/CCS solenoid circuit intermittent failure(s) detected. | See TIMING/COAST CLUTCH (2-3T/CCS) SOLENOID . |
| P0894 | Transaxle Component Slipping | Internal transaxle concern | See DIAGNOSIS BY SYMPTOM . |
| P0895 | Shift Time Too Short | Transaxle shift concern | See SHIFT POINT ROAD TEST . |
| P0896 | Shift Time Too Long | Transaxle shift concern | See SHIFT POINT ROAD TEST . |
| P0960 | Pressure Control Solenoid A Control Circuit / Open | EPC solenoid circuit failure, open circuit. | See ELECTRONIC PRESSURE CONTROL (EPC) SOLENOID . |
| P0961 | Pressure Control Solenoid A Control Circuit Range/Performance | EPC solenoid circuit out of range. | See ELECTRONIC PRESSURE CONTROL (EPC) SOLENOID . |
| P0962 | Pressure Control Solenoid A Control Circuit Low | EPC solenoid circuit failure, shorted to ground. | See ELECTRONIC PRESSURE CONTROL (EPC) SOLENOID . |
| P0963 | Pressure Control Solenoid A Control Circuit High | EPC solenoid circuit failure, short circuit to VBAT. | See ELECTRONIC PRESSURE CONTROL (EPC) SOLENOID . |
| P0964 | Pressure Control Solenoid B Control Circuit / Open | 3-2T/CCS solenoid circuit failure - open. | See TIMING/COAST CLUTCH (2-3T/CCS) SOLENOID . |
| P0965 | Pressure Control Solenoid B Control Circuit Range/Performance | 3-2T/CCS solenoid circuit out of range. | See TIMING/COAST CLUTCH (2-3T/CCS) SOLENOID . |
| P0966 | Pressure Control Solenoid B Control Circuit Low | 3-2T/CCS solenoid circuit failure - short. | See TIMING/COAST CLUTCH (2-3T/CCS) SOLENOID . |
| P0967 | Pressure Control Solenoid B Control Circuit High | 3-2T/CCS solenoid circuit failure - short to VBAT. | See TIMING/COAST CLUTCH (2-3T/CCS) SOLENOID . |
| P1000 | OBD Systems Readiness Test Not Complete | OBD II monitor testing not complete. | See OBD II DRIVE CYCLE MALFUNCTION . |
| P1001 | KOER Not Able to Complete, KOER Aborted (Data link connector malfunction) |
|
See DATA LINK CONNECTOR MALFUNCTION . |
| P1100 | Mass Air Flow (MAF) Sensor Circuit Intermittent | MAF/IAT signal went below 0.23 volt or above 4.60 volts sometime during the last 40 warm-up cycles. | See MASS AIR FLOW (MAF) SENSOR . |
| P1101 | Mass Air Flow (MAF) Sensor Out Of Self Test Range | MAF/IAT signal was greater than 0.27 volt during KOEO Self-Test or MAF/IAT signal was not between 0.46-2.44 volts during KOER Self-Test. | See MASS AIR FLOW (MAF) SENSOR . |
| P1102 | Mass Air Flow (MAF) Sensor In Range But Lower Than Expected | MAF/IAT signal was lower than expected. | See MASS AIR FLOW (MAF) SENSOR . |
| P1103 | Mass Air Flow (MAF) Sensor In Range But Higher Than Expected | MAF/IAT signal was higher than expected. | See MASS AIR FLOW (MAF) SENSOR . |
| P1110 | Intake Air Temperature (IAT) Circuit (D/C) Open/Short | IAT sensor signal was low during the Comprehensive Component Monitor (CCM). | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P1112 | Intake Air Temperature (IAT) Circuit Intermittent | IAT sensor signal was intermittent during the Comprehensive Component Monitor (CCM). | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P1113 | Intake Air Temperature (IAT) Circuit (L/C) Open/Short | IAT sensor signal was missing during the Comprehensive Component Monitor (CCM). | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P1116 | Engine Coolant Temperature Sensor put Of Self Test Range | ECT signal went out of Self-Test range (0.3-3.7 volts). | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P1117 | Engine Coolant Temperature Sensor Circuit Intermittent | ECT circuit was intermittently open or shorted while engine was running. | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P1120 | Throttle Position Sensor A Out Of Range Low (Ratch too low) | TP sensor signal falls between 0.17 and 0.49V (3.42 and 9.85%). | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P1121 | Pedal Position Sensor A Circuit Range/Performance | TP sensor signal is inconsistent with MAF/IAT sensor signal. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P1122 | Throttle Position Sensor A In Range But Lower Than Expected | Consistency concern with throttle position (TP) sensor circuit. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P1123 | Throttle Position Sensor A In Range But Higher Than Expected | Consistency concern with throttle position (TP) sensor circuit. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P1124 | Throttle Position Sensor A Out Of Self Test Range | TP sensor's rotational setting and signal are not in Self-Test range of 0.66 to 1.17V (13.27 to 23.52%). | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P1125 | Throttle Position Sensor A Intermittent | TP sensor signal went below 0.49V or above 4.65V sometime during the last 80 warm-up cycles. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P1126 | Throttle Position (Narrow Range) Sensor Circuit | TP sensor signal went out of range sometime during the last 80 warm-up cycles. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P1127 | Exhaust Temperature Out of Range, 02 Sensor Tests Not Completed | The inferred exhaust temperature to determine when HO2S heaters are cycled ON is below a minimum calibrated value. | See HO2S HEATER(S) . |
| P1128 | Upstream HO2S Sensors Swapped (see P0040) | During KOER testing the front HO2S signal(s) response for a fuel shift to the correct engine bank was not indicated. | See HEATED OXYGEN SENSOR (HO2S) SIGNALS . |
| P1129 | Downstream HO2S Sensors Swapped (see P0041) | During KOER testing the front HO2S signal(s) response for a fuel shift to the correct engine bank was not indicated. | See HEATED OXYGEN SENSOR (HO2S) SIGNALS . |
| P1130 | Lack Of HO2S11 Switches - Fuel Trim At Limit | HO2S-11 (Front Bank 1) fails to switch due to circuit or fuel at or exceeding a calibrated limit. | See FUEL SYSTEM NOT SWITCHING AT FUEL TRIM (RICH OR LEAN) . |
| P1131 | Lack Of HO2S11 Switches - Sensor Indicates Lean (see P2195) | HO2S sensor is indicating lean at the end of the test trying to correct for an over-rich condition. The test fails when the fuel control system no longer detects a switch for a calibrated amount of time. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P1132 | Lack Of HO2S11 Switches - Sensor Indicates Rich (see XREF P2196) | HO2S sensor is indicating rich at the end of the test trying to correct for an over-lean condition. The test fails when the fuel control system no longer detects a switch for a calibrated amount of time. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P1133 | Bank 1 Fuel Control Shifted Lean (FAOSC) (See P2096) | HO2S sensor is indicating lean at the end of the test trying to correct for an over-rich condition. | See HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT . |
| P1134 | Bank 1 Fuel Control Shifted Rich (FAOSC) (See P2097) | HO2S sensor is indicating rich at the end of the test trying to correct for an over-lean condition. | See HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT . |
| P1137 | Lack Of HO2S12 Switches - Sensor Indicates Lean | The rear HO2S (Bank 1) is forced rich and lean by the powertrain control module (PCM). The test fails if the PCM does not detect the rich signal (P1137) or lean signal (P1138) during KOER Self-Test. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P1138 | Lack Of HO2S12 Switches - Sensor Indicates Rich | The rear HO2S (Bank 1) is forced rich and lean by the powertrain control module (PCM). The test fails if the PCM does not detect the rich signal (P1137) or lean signal (P1138) during KOER Self-Test. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P1141 | HO2S12 Heater Circuit Low | HO2S heater circuit out of range - low. | See HEATED OXYGEN SENSOR (HO2S) OVER VOLTAGE . |
| P1142 | HO2S12 Heater Circuit High | HO2S heater circuit out of range - high. | See HEATED OXYGEN SENSOR (HO2S) OVER VOLTAGE . |
| P1150 | Lack Of HO2S21 Switches - Fuel Trim At Limit | HO2S-21 (Front Bank 2) fails to switch due to circuit or fuel at/or exceeding a calibrated limit. | See FUEL SYSTEM NOT SWITCHING AT FUEL TRIM (RICH OR LEAN) . |
| P1151 | Lack Of HO2S21 Switches - Sensor Indicates Lean (see P2197) | HO2S sensor is indicating lean at the end of the test trying to correct for an over-rich condition. The test fails when the fuel control system no longer detects a switch for a calibrated amount of time. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P1152 | Lack Of HO2S21 Switches - Sensor Indicates Rich (see P2198) | HO2S sensor is indicating rich at the end of the test trying to correct for an over-lean condition. The test fails when the fuel control system no longer detects a switch for a calibrated amount of time. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P1153 | Bank 2 Fuel Control Shifted Lean (FAOSC) (See P2098) | HO2S sensor is indicating lean at the end of the test trying to correct for an over-rich condition. | See HEATED OXYGEN SENSOR (HO2S) . |
| P1154 | Bank 2 Fuel Control Shifted Rich (FAOSC) (See P2099) | HO2S sensor is indicating rich at the end of the test trying to correct for an over-lean condition. | See HEATED OXYGEN SENSOR (HO2S) . |
| P1157 | Lack Of HO2S22 Switches - Sensor Indicates Lean (see P2272) | The rear HO2S (Bank 2) is forced rich and lean by the powertrain control module (PCM). The test fails if the PCM does not detect the rich signal (P1157) or lean signal (P1158) during KOER Self-Test. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P1158 | Lack Of HO2S22 Switches - Sensor Indicates Rich (see P2273) | The rear HO2S (Bank 2) is forced rich and lean by the powertrain control module (PCM). The test fails if the PCM does not detect the rich signal (P1157) or lean signal (P1158) during KOER Self-Test. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P1168 | Fuel Rail Pressure Sensor In Range But Low | FRPT indicates fuel pressure below calibrated minimum limit. | See FUEL RAIL PRESSURE TEMPERATURE (FRPT) SENSOR . |
| P1169 | Feedback A/F Mixture Control (HO2S12) | FRPT indicates fuel pressure above calibrated maximum limit. | See FUEL RAIL PRESSURE TEMPERATURE (FRPT) SENSOR . |
| P1170 | Feedback A/F Mixture Control (HO2S11) | Front HO2S of Bank 1 heater circuit is open, shorted to ground, shorted to VPWR or has low or high current draw. | See HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT . |
| P1173 | Feedback A/F Mixture Control (HO2S21) | Rear HO2S of Bank 1 heater circuit is open, shorted to ground, shorted to VPWR or has low or high current draw. | See HEATED OXYGEN SENSOR (HO2S) . |
| P1195 | BARO Sensor Circuit | Manifold Absolute Pressure (MAP) sensor input to the powertrain control module (PCM) is not within the calibrated value. | See MANIFOLD ABSOLUTE PRESSURE (MAP)SENSOR . |
| P1224 | Throttle Position (TP) Sensor B Out Of Self Test Range | TP sensor circuit out of range. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P1233 | Fuel Pump Driver Module Disabled or Off Line (Fuel Pump Driver Module) | Powertrain control module (PCM) not receiving duty cycle signal from fuel pump module. | See FUEL PUMP (FP) PRIMARY OR SECONDARY CIRCUIT . |
| P1234 | Fuel Pump Driver Module Disabled or Off Line (Fuel Pump Driver Module) | Powertrain control module (PCM) not receiving duty cycle signal from fuel pump module. | See FUEL PUMP (FP) PRIMARY OR SECONDARY CIRCUIT . |
| P1235 | Fuel Pump Control out Of Range (Fuel Pump Driver Module/VLCM) | Invalid or missing FP data, from powertrain control module (PCM) to FPDM. | See FUEL PUMP (FP) PRIMARY OR SECONDARY CIRCUIT . |
| P1236 | Fuel Pump Control Out Of Range (Fuel Pump Driver Module) | Invalid or missing FP data from powertrain control module (PCM) to FPDM. | See FUEL PUMP (FP) PRIMARY OR SECONDARY CIRCUIT . |
| P1237 | Fuel Pump Secondary Circuit (Fuel Pump Driver Module) | Fuel pump unit secondary circuit failure. | See FUEL PUMP (FP) PRIMARY OR SECONDARY CIRCUIT . |
| P1238 | Fuel Pump Secondary Circuit (Fuel Pump Driver Module) | Fuel pump unit secondary circuit failure. | See FUEL PUMP (FP) PRIMARY OR SECONDARY CIRCUIT . |
| P1239 | Speed Fuel Pump Positive Feed | Fuel pump unit secondary circuit failure. | See FUEL PUMP (FP) PRIMARY OR SECONDARY CIRCUIT . |
| P1244 | Alternator Load High Input (see P0626) | The Generator Load Input (GLI) is not within a calibrated limit for a calibrated amount of time. | See GENERATOR/REGULATOR SYSTEM MALFUNCTION . |
| P1245 | Alternator Load Low Input (see P0625) | The Generator Load Input (GLI) is not within a calibrated limit for a calibrated amount of time. | See GENERATOR/REGULATOR SYSTEM MALFUNCTION . |
| P1246 | Alternator Load Input (see P0622) | The Generator Load Input (GLI) is not within a calibrated limit for a calibrated amount of time. | See GENERATOR/REGULATOR SYSTEM MALFUNCTION . |
| P1260 | Theft Detected, Vehicle Immobilized | Anti-theft system has determined a theft condition existed and the engine is disabled. | See ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) . |
| P1261 | Cylinder #1 High To Low Side Short | Concern detected by the fuel injector interface module in the secondary (rearward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P1262 | Cylinder #2 High To Low Side Short | Concern detected by the fuel injector interface module in the secondary (rearward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P1263 | Cylinder #3 High To Low Side Short | Concern detected by the fuel injector interface module in the secondary (rearward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P1264 | Cylinder #4 High To Low Side Short | Concern detected by the fuel injector interface module in the secondary (rearward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P1265 | Cylinder #5 High To Low Side Short | Concern detected by the fuel injector interface module in the secondary (rearward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P1266 | Cylinder #6 High To Low Side Short | Concern detected by the fuel injector interface module in the secondary (rearward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P1270 | Engine RPM or Vehicle Speed Limiter Reached | Vehicle has been operated in a manner which caused the engine or vehicle to exceed a calibration limit. | See ENGINE RPM/VEHICLE SPEED LIMITER . |
| P1271 | Cylinder #1 High To Low Side Short | Concern detected by the fuel injector interface module in the secondary (rearward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P1272 | Cylinder #2 High To Low Side Short | Concern detected by the fuel injector interface module in the secondary (rearward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P1273 | Cylinder #3 High To Low Side Short | Concern detected by the fuel injector interface module in the secondary (rearward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P1274 | Cylinder #4 High To Low Side Short | Concern detected by the fuel injector interface module in the secondary (rearward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P1275 | Cylinder #5 High To Low Side Short | Concern detected by the fuel injector interface module in the secondary (rearward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P1276 | Cylinder #6 High To Low Side Short | Concern detected by the fuel injector interface module in the secondary (rearward) fuel injector circuit. | See FUEL INJECTOR MALFUNCTION . |
| P1285 | Cylinder Head Overtemperature Condition | Overheat condition was sensed by the cylinder head temperature (CHT) sensor. | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P1288 | Cylinder Head Temperature (CHT) Sensor Out Of Self Test Range | The CHT sensor is out of Self-Test range (engine not at operating temperature). | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P1289 | Cylinder Head Temperature (CHT) Sensor Circuit High | CHT sensor circuit malfunction. | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P1290 | Cylinder Head Temperature (CHT) Sensor Circuit Low | CHT sensor circuit malfunction. | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P1299 | Cylinder Head Overtemperature Protection Active | Overheat condition was detected by the CHT sensor and an FMEM strategy Called-Fail safe Cooling was activated to cool the engine. | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P1308 | A/C Clutch Circuit | Air conditioning clutch circuit out of range. | See PINPOINT TEST 3: THE AIR CONDITIONING (A/C) IS INOPERATIVE . |
| P1309 | Misfire Monitor Hardware - CMP Misaligned, CKP/CMP Noise, PCM AICE Chip | Misfire Detection Monitor is disabled, usually due to the input signal generated by the camshaft position sensor (CMP) when sensing the passage of teeth from the CMP wheel. | See MISFIRE DETECTION MONITOR DISABLED . |
| P1336 | Crankshaft/Camshaft Sensor Range/Performance | Camshaft Position (CMP) sensor circuit failure. | See CAMSHAFT POSITION SENSOR (CMP) MALFUNCTION . |
| P1340 | Camshaft Position Sensor B Circuit | Camshaft Position (CMP) sensor circuit failure. | See CAMSHAFT POSITION SENSOR (CMP) MALFUNCTION . |
| P1341 | Camshaft Position Sensor B Circuit Range/Performance | Camshaft Position (CMP) sensor circuit out of range. | See CAMSHAFT POSITION SENSOR (CMP) MALFUNCTION . |
| P1345 | Cylinder Discrimination Signal (from CMP sensor) | Camshaft Position (CMP) sensor circuit failure. | See CAMSHAFT POSITION SENSOR (CMP) MALFUNCTION . |
| P1352 | Ignition Coil A Primary Circuit | Primary side of the coil has failed from the ignition module (integrated in the powertrain control module [PCM]). | See INTEGRATED IGNITION COIL 1, 2, 3, 4, 5, OR 6 FAILURE . |
| P1353 | Ignition Coil B Primary Circuit | Primary side of the coil has failed from the ignition module (integrated in the PCM). | See INTEGRATED IGNITION COIL 1, 2, 3, 4, 5, OR 6 FAILURE . |
| P1354 | Ignition Coil C Primary Circuit | Primary side of the coil has failed from the ignition module (integrated in the powertrain control module [PCM]). | See INTEGRATED IGNITION COIL 1, 2, 3, 4, 5, OR 6 FAILURE . |
| P1355 | Ignition Coil D Primary Circuit | Primary side of the coil has failed from the ignition module (integrated in the powertrain control module [PCM]). | See INTEGRATED IGNITION COIL 1, 2, 3, 4, 5, OR 6 FAILURE . |
| P1360 | Ignition Coil A Primary Circuit | Primary side of the coil has failed from the ignition module (integrated in the powertrain control module [PCM]). | See INTEGRATED IGNITION COIL 1, 2, 3, 4, 5, OR 6 FAILURE . |
| P1361 | Ignition Coil B Primary Circuit | Primary side of the coil has failed from the ignition module (integrated in the powertrain control module [PCM]). | See INTEGRATED IGNITION COIL 1, 2, 3, 4, 5, OR 6 FAILURE . |
| P1362 | Ignition Coil C Primary Circuit | Primary side of the coil has failed from the ignition module (integrated in the powertrain control module [PCM]). | See INTEGRATED IGNITION COIL 1, 2, 3, 4, 5, OR 6 FAILURE . |
| P1363 | Ignition Coil D Primary Circuit | Primary side of the coil has failed from the ignition module (integrated in the powertrain control module [PCM]). | See INTEGRATED IGNITION COIL 1, 2, 3, 4, 5, OR 6 FAILURE . |
| P1364 | Ignition Coil Primary Circuit | Primary side of the coil has failed from the ignition module (integrated in the powertrain control module [PCM]). | See INTEGRATED IGNITION COIL 1, 2, 3, 4, 5, OR 6 FAILURE . |
| P1365 | Ignition Coil Secondary Circuit | Secondary side of the coil has failed. | See INTEGRATED IGNITION COIL 1, 2, 3, 4, 5, OR 6 FAILURE . |
| P1380 | Camshaft Position Actuator Circuit (Bank 1) | Voltage has exceeded or fell below a calibrated limit for a calibrated length of time. | CAMSHAFT POSITION SENSOR (CMP) MALFUNCTION . |
| P1381 | Camshaft Position Timing Over Advanced (Bank 1) | Camshaft timing exceeded a calibrated value or remained in an advanced position. | CAMSHAFT POSITION SENSOR (CMP) MALFUNCTION . |
| P1382 | Camshaft Position Timing Solenoid #1 Circuit | Camshaft timing out of range. | CAMSHAFT POSITION SENSOR (CMP) MALFUNCTION . |
| P1383 | Camshaft Position Timing Over Retarded (Bank 1) | Camshaft timing exceeded a calibrated value or remained in an retarded position. | CAMSHAFT POSITION SENSOR (CMP) MALFUNCTION . |
| P1385 | Camshaft Position Actuator Circuit (Bank 2) | Voltage has exceeded or fell below a calibrated limit for a calibrated length of time. | CAMSHAFT POSITION SENSOR (CMP) MALFUNCTION . |
| P1386 | Camshaft Position Timing Over Advanced (Bank 2) | Camshaft timing exceeded a calibrated value or remained in an advanced position. | CAMSHAFT POSITION SENSOR (CMP) MALFUNCTION . |
| P1387 | Camshaft Position Timing Solenoid #2 Circuit | Camshaft timing out of range. | CAMSHAFT POSITION SENSOR (CMP) MALFUNCTION . |
| P1388 | Camshaft Position Timing Over Retarded (Bank 2) | Camshaft timing exceeded a calibrated value or remained in an retarded position. | CAMSHAFT POSITION SENSOR (CMP) MALFUNCTION . |
| P1400 | Differential Pressure Feedback EGR Circuit Low | The average voltage of the DPFEGR SIG circuit input is below minimum (0.2 V). | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P1401 | Differential Pressure Feedback EGR Circuit High | The average voltage of the DPFEGR SIG circuit input is above maximum (4.5 V). | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P1402 | Exhaust Gas Recirculation Valve Position Sensor Circuit | DPFEGR SIG circuit input is out of range. | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P1403 | Differential Pressure Feedback Sensor Hoses Reversed | DPFEGR SIG circuit input is out of range. | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P1405 | Differential Pressure Feedback Sensor Upstream Hose Off Or Plugged | Exhaust manifold side (upstream) DPFEGR sensor pressure hose is off or plugged. | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P1406 | Differential Pressure Feedback Sensor Downstream Hose Off Or Plugged | Exhaust manifold side (downstream) DPFEGR sensor pressure hose is off or plugged. | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P1407 | Exhaust Gas Recirculation No Flow Detected | No flow detected. | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P1408 | Exhaust Gas Recirculation Flow Out Of Self Test Range | EGR flow is less than required calibrated limit. | See EGR SYSTEM MALFUNCTION - 2.3L or EGR SYSTEM MALFUNCTION - 3.0L . |
| P1409 | EGR Vacuum Regulator Solenoid Circuit | Self-test has detected an electrical malfunction in EGRVR circuit. | See EGR VACUUM REGULATOR (EGRVR) SOLENOID CIRCUIT MALFUNCTION . |
| P1412 | Exhaust Gas Recirculation Valve Frozen | EGR flow is out of range. | See EGR SYSTEM MALFUNCTION - 2.3L or EGR SYSTEM MALFUNCTION - 3.0L . |
| P1442 | Evaporative Emission (EVAP) System Control Leak Detected | A substantial leak and no purge flow has been detected in the EVAP system when there is -7.0 in-H2 O (01.74 kpa) or less vacuum for 30 seconds evaluation time with less than 0.02 lb/min vapor flow. | See EVAPORATIVE EMISSION (EVAP) SYSTEM MALFUNCTION . |
| P1443 | Evaporative Emission (EVAP) System Control Valve (low/no flow) | A substantial leak and no purge flow has been detected in the EVAP system when there is -7.0 in-H2 O (01.74 kpa) or less vacuum for 30 seconds evaluation time with less than 0.02 lb/min vapor flow. | See EVAPORATIVE EMISSION (EVAP) SYSTEM MALFUNCTION . |
| P1444 | Evaporative Emission (EVAP) System Purge Flow Sensor Circuit Low | EVAP canister purge valve voltage low. | See EVAPORATIVE EMISSION (EVAP) SYSTEM MALFUNCTION . |
| P1445 | Evaporative Emission (EVAP) System Purge Flow Sensor Circuit High | EVAP canister purge valve voltage high. | See EVAPORATIVE EMISSION (EVAP) SYSTEM MALFUNCTION . |
| P1450 | Unable to Bleed Up Fuel Tank Vacuum | Self-Test has detected the EVAP system is unable to bleed up fuel tank vacuum. | See EVAPORATIVE EMISSION (EVAP) MONITOR AND SYSTEM . |
| P1451 | Evaporative Emission (EVAP) System Vent Control Circuit | Self-Test has detected a Canister Vent (CV) solenoid circuit failure. | See CANISTER VENT (CV) SOLENOID MALFUNCTION . |
| P1452 | Unable to Bleed Up Fuel Tank Vacuum | Self-Test has detected the EVAP system is unable to bleed up fuel tank vacuum. | See EVAPORATIVE EMISSION (EVAP) MONITOR AND SYSTEM . |
| P1455 | Fuel Tank Level Sensor Circuit | Fuel tank level sensor out of range. | See PINPOINT TEST 3: INCORRECT FUEL GAUGE INDICATION . |
| P1457 | Purge Solenoid Control System | EVAP canister purge valve out of range. | See EMISSION (EVAP) SYSTEM MALFUNCTION . |
| P1460 | Wide Open Throttle A/C Cutout Circuit | Excessive current draw is detected on the ACCR circuit when powertrain control module (PCM) grounds the circuit or voltage is not detected on the ACCR circuit when the circuit is not grounded by the PCM. | See A/C CLUTCH RELAY (ACCR) MALFUNCTION . |
| P1461 | A/C Pressure Sensor Circuit High | ACP voltage input to the powertrain control module (PCM) is above a calibrated level. | See A/C PRESSURE SENSOR (ACP) MALFUNCTION . |
| P1462 | A/C Pressure Sensor Circuit Low | ACP voltage input to the powertrain control module (PCM) is below a calibrated level. | See A/C PRESSURE SENSOR (ACP) MALFUNCTION . |
| P1463 | A/C Pressure Sensor Insufficient Pressure Change | Change in A/C system pressure is outside calibrated value when A/C clutch engages. | See A/C PRESSURE SENSOR (ACP) MALFUNCTION . |
| P1464 | A/C Demand Out Of Self Test Range | The ACCS input to powertrain control module (PCM) was high during Self-Test. | See A/C CONTROL SIGNAL (ACCS) MALFUNCTION . |
| P1469 | Rapid A/C Cycling | Frequent A/C compressor clutch cycling. | See SYMPTOM TROUBLESHOOTING CHART - AIR CONDITIONING (A/C) . |
| P1474 | Fan Control Primary Circuit | Excessive current draw is detected on the Low Fan Control (LFC) circuit when the powertrain control module (PCM) grounds the circuit or with the LFC circuit not grounded by the PCM, voltage is not detected on the LFC circuit (the PCM expects to detect VPWR voltage coming through the low speed FC relay coil to the LFC circuit). | See COOLING FAN MALFUNCTION . |
| P1475 | Fan Relay (Low) Circuit | Fan relay circuit voltage low. | See COOLING FAN MALFUNCTION . |
| P1476 | Fan Relay (High) Circuit | Fan relay circuit voltage high. | See COOLING FAN MALFUNCTION . |
| P1477 | Additional Fan Relay Circuit | Excessive current draw is detected on the Medium Fan Control (MFC) circuit when the powertrain control module (PCM) grounds the circuit or with the MFC circuit not grounded by the PCM, voltage is not detected on the MFC circuit (the PCM expects to detect IGN START/RUN voltage coming through the low speed FC relay coil to the MFC circuit). | See COOLING FAN MALFUNCTION . |
| P1479 | High Fan Control Primary Circuit | Excessive current draw is detected on the High Fan Control (HFC) circuit when the powertrain control module (PCM) grounds the circuit or with the HFC circuit not grounded by the powertrain control module (PCM), voltage is not detected on the HFC circuit (the PCM expects to detect VPWR voltage coming through the low speed FC relay coil to the HFC circuit). | See COOLING FAN MALFUNCTION . |
| P1480 | Fan Secondary Low With Low Fan On | Fan relay circuit voltage low. | See COOLING FAN MALFUNCTION . |
| P1481 | Fan Secondary Low With High Fan On | Fan relay circuit voltage high. | See COOLING FAN MALFUNCTION . |
| P1485 | EGRV Circuit | Exhaust gas recirculation (EGR) circuit out of range. | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P1486 | EGRA Circuit | Exhaust gas recirculation (EGR) circuit out of range. | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P1487 | Exhaust Gas Recirculation Check Solenoid Circuit | Circuit malfunction. | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P1496 | Exhaust Gas Recirculation (EGR) Stepper Motor 1 Control Circuit Low/High | EGR stepper motor circuit out of range. | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P1497 | Exhaust Gas Recirculation (EGR) Stepper Motor 2 Control Circuit Low/High | EGR stepper motor circuit out of range. | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P1498 | Exhaust Gas Recirculation (EGR) Stepper Motor 3 Control Circuit Low/High | EGR stepper motor circuit out of range. | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P1499 | Exhaust Gas Recirculation (EGR) Stepper Motor 4 Control Circuit Low/High | EGR stepper motor circuit out of range. | See DIFFERENTIAL PRESSURE FEEDBACK (DPFEGR) SENSOR MALFUNCTION . |
| P1500 | Vehicle Speed Sensor (VSS) | VSS input signal was intermittent. This DTC is set when a VSS fault interferes with other OBD II tests, such as Catalyst efficiency monitor, EVAP monitor, HO2S monitor, etc. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P1501 | Vehicle Speed Sensor Out Of Self Test Range | VSS input signal is out of Self-Test range. If the powertrain control module (PCM) detects a VSS input signal any time during Self-Test (vehicle stopped), a DTC P1501 Will beset and the test will abort. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P1502 | Vehicle Speed Sensor (VSS) Intermittent | Powertrain control module (PCM) has detected an error in the vehicle speed information received from the VSS Sensor. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P1504 | Idle Air Control (IAC) Circuit | An electrical load failure on IAC output circuit. | See IDLE AIR CONTROL (IAC) VALVE ASSEMBLY MALFUNCTION . |
| P1505 | Idle Air Control (IAC) System At Adaptive Clip | An electrical load failure on IAC output circuit. | See IDLE AIR CONTROL (IAC) VALVE ASSEMBLY MALFUNCTION . |
| P1506 | Idle Air Control (IAC) Overspeed Error | Powertrain control module (PCM) detected an engine idle speed greater than the desired RPM. | See IDLE AIR CONTROL (IAC) SYSTEM MALFUNCTION . |
| P1507 | Idle Air Control (IAC) Underspeed Error | Engine idle speed is less than desired RPM. | See IDLE AIR CONTROL (IAC) VALVE ASSEMBLY MALFUNCTION . |
| P1512 | Intake Manifold Runner Control Stuck Closed (Bank 1) | IMTV was commanded open, but signal indicates closed. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P1513 | Intake Manifold Runner Control Stuck Closed (Bank 2) | IMTV was commanded open, but signal indicates closed. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P1516 | Intake Manifold Runner Control Input Error (Bank 1) | IMTV signal outside expected calibrated range. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P1517 | Intake Manifold Runner Control Input Error (Bank 2) | IMTV commanded close, but signal indicates open. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P1518 | Intake Manifold Runner Control Stuck Open (Bank 1) | IMTV commanded close, but signal indicates open. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P1519 | Intake Manifold Runner Control Stuck Closed (Bank 1) | IMTV commanded open, but signal indicates closed. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P1520 | Intake Manifold Runner Control Circuit | IMTV primary circuit failure. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P1532 | Intake Manifold Communication Control Circuit (Bank 2) | IMTV primary circuit failure. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P1537 | Intake Manifold Runner Control Stuck Open (Bank 1) | IMTV commanded close, but signal indicates open. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P1538 | Intake Manifold Runner Control Stuck Open (Bank 2) | IMTV commanded close, but signal indicates open. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P1541 | Intake Manifold Runner Control Circuit Range/Performance | IMTV out of range. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P1549 | Intake Manifold Communication Control Circuit (Bank 1) | IMTV communication control circuit malfunction. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P1550 | Power Steering Pressure (PSP) Sensor Out Of Self Test Range | PSP signal to the powertrain control module (PCM) is above or below calibrated range. | See POWER STEERING PRESSURE (PSP) SWITCH MALFUNCTION . |
| P1562 | Powertrain control module (PCM) B+ Voltage Low (KAM power) | PCM voltage low. | See SYMPTOM TROUBLESHOOTING CHART - CHARGING SYSTEM . |
| P1565 | Speed Control Command Switch Out Of Range High | Speed control out of calibrated parameters. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P1567 | Speed Control Output Circuit | Speed control out of calibrated parameters. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P1568 | Speed Control Unable to Hold Speed | Speed control out of calibrated parameters. | See SYMPTOM TROUBLESHOOTING CHART - SPEED CONTROL . |
| P1569 | Intake Manifold Runner Control Circuit Low | IMTV primary circuit failure. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P1570 | Intake Manifold Runner Control Circuit High | IMTV primary circuit failure. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P1572 | Brake Pedal Switch Circuit | BPP and brake pressure applied (BPA) inputs to the powertrain control module (PCM) do not agree. | See BRAKE PEDAL POSITION (BPP) SWITCH MALFUNCTION . |
| P1573 | Throttle Position (TP) Not Available | TP sensor malfunction. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P1574 | Throttle Position Sensor Outputs Disagree | TP sensor malfunction. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P1600 | Loss Of KAM Power, Circuit Open | Low/no voltage to powertrain control module (PCM). | See SYMPTOM TROUBLESHOOTING CHART - CHARGING SYSTEM . |
| P1630 | Alternator Regulator #1 Control Circuit. | Alternator regulator circuit out of range. | See GENERATOR/REGULATOR SYSTEM MALFUNCTION . |
| P1631 | Alternator Regulator #2 Control Circuit | Alternator regulator circuit out of range. | See GENERATOR/REGULATOR SYSTEM MALFUNCTION . |
| P1633 | Generator Control System - over charge | Generator/regulator system malfunction. | See SYMPTOM TROUBLESHOOTING CHART - CHARGING SYSTEM . |
| P1634 | Generator Control System - no charge | Generator/regulator system malfunction. | See GENERATOR/REGULATOR SYSTEM MALFUNCTION . |
| P1635 | Tire/Axle Out of Acceptable Range | Wheels/Tires out of calibrated range. | See PINPOINT TEST 9: TIRE/AXLE OUT OF ACCEPTABLE RANGE . |
| P1636 | Inductive Signature Chip Communication Error | Powertrain control module (PCM) has lost communications with the inductive signature chip. | See POWERTRAIN CONTROL MODULE (PCM) MALFUNCTION . |
| P1637 | CAN Link ECM/ABS Control Module Circuit/Network | Communication network malfunction. | See SYSTEM PRE-CHECK . |
| P1639 | Vehicle ID Block Corrupted, Not Programmed | Powertrain control module (PCM) programmable parameters are corrupted or not programmed correctly. | See POWERTRAIN CONTROL MODULE (PCM) MALFUNCTION . |
| P1641 | Fuel Pump Primary Circuit | Fuel pump delivery module. | See FUEL PUMP (FP) PRIMARY OR SECONDARY CIRCUIT . |
| P1642 | CAN Link Circuit | Powertrain control module (PCM) programmable parameters are corrupted or not programmed correctly. | See SYSTEM PRE-CHECK . |
| P1643 | CAN Link Engine Control Module/Transaxle Control Module Circuit/Network | Powertrain control module (PCM) programmable parameters are corrupted or not programmed correctly. | See SYSTEM PRE-CHECK . |
| P1650 | Power Steering Pressure (PSP) Switch Out Of Self Test Range | PSP signal to the powertrain control module (PCM) is high during KOEO or PSP signal did not change state during KOER. | See POWER STEERING PRESSURE (PSP) SWITCH MALFUNCTION . |
| P1651 | Power Steering Pressure (PSP) Switch Input | PSP signal is open or shorted (powertrain control module (PCM) expects PSP signal to change after a calibrated number of speed transitions). | See POWER STEERING PRESSURE (PSP) SWITCH MALFUNCTION . |
| P1656 | CAN Link PCM/PCM Circuit/Network | Communication network malfunction. | See SYSTEM PRE-CHECK . |
| P1657 | CAN Link Chip Malfunction | Communication network malfunction. | See SYSTEM PRE-CHECK . |
| P1700 | Transaxle Indeterminate Failure (Failed to Neutral) | Internal component failure. Direct one-way clutch failure. Failed a neutral condition. FMEM becomes active - engine rpm limited to 4, 000 rpms. Other DTCs that may have set P1700: P0750, P0755, P1714, P1715, P1747, P1760. | If other solenoid DTCs are present, diagnose and repair them first. Clear the DTCs and drive the vehicle. If DTC P1700 returns, disassemble transaxle and inspect the direct one-way clutch. Repair as required. Clear DTCs. Drive vehicle and verify repair. |
| P1701 | Reverse Engagement Error | Internal component failure. Direct one-way clutch failure. Failed a neutral condition. FMEM becomes active - engine rpm limited to 4, 000 rpms. Other DTCs may have set. | If other DTCs are present, diagnose and repair them first. Clear the DTCs and drive the vehicle. If DTC P1700 returns, disassemble transaxle and inspect. Repair as required. Clear DTCs. Drive vehicle and verify repair. |
| P1702 | Transaxle Range (TR) Sensor Circuit Intermittent | TR signal intermittent. | See TRANSAXLE RANGE (TR) SENSOR . |
| P1703 | Brake Switch Out Of Self Test Range | BPP signal was high (KOEO) or BPP signal did not cycle high or low (KOER). | See BRAKE PEDAL POSITION (BPP) SWITCH MALFUNCTION . |
| P1704 | Transaxle Range Circuit Not Indicating Park/Neutral During Self Test | TR signal is not in PARK during KOEO Self-Test. | See TRANSAXLE RANGE (TR) SENSOR . |
| P1705 | Transaxle Range Circuit Not Indicating Park/Neutral During Self Test | TR signal is not in PARK during KOEO Self-Test. | See TRANSAXLE RANGE (TR) SENSOR . |
| P1708 | Clutch Switch Circuit | Voltage is high or the switch is open when voltage should be low or switch should be closed grounding the circuit. | See CLUTCH PEDAL POSITION (CPP) SWITCH MALFUNCTION . |
| P1709 | Park Neutral Position Switch Out Of Self Test Range | Voltage is high or the switch is open when voltage should be low or switch should be closed grounding the circuit. | See CLUTCH PEDAL POSITION (CPP) SWITCH MALFUNCTION . |
| P1711 | Transaxle Fluid Temperature Sensor Out Of Self Test Range | TFT not at operating temperature during self-test. | See TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR . |
| P1713 | Transaxle Fluid Temperature Sensor In Range Failure (< 50 deg F) | Powertrain control module (PCM) has detected no TFT change at low range during operation. | See TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR . |
| P1714 | Shift Solenoid A Inductive Signature | SS1 malfunction. | See SOLENOID MECHANICAL FAILURE . |
| P1715 | Shift Solenoid B Inductive Signature | SS2 malfunction. | See SOLENOID MECHANICAL FAILURE . |
| P1718 | Transaxle Fluid Temperature Sensor In Range Failure (> 250 deg F) | Powertrain control module (PCM) has detected no TFT change at high range during operation. | See TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR . |
| P1719 | Engine Torque Signal | TCC function check. | See SHIFT SOLENOIDS . |
| P1721 | Gear 1 Incorrect Ratio | SS1 solenoid circuit failure, open or short. | See SHIFT SOLENOIDS . |
| P1722 | Gear 2 Incorrect Ratio | SS2 solenoid circuit failure, open or shorted. | See SHIFT SOLENOIDS . |
| P1723 | Gear 3 Incorrect Ratio | SS3 solenoid circuit failure, open or shorted. | See SHIFT SOLENOIDS . |
| P1724 | Gear 4 Incorrect Ratio | SS4 solenoid circuit failure, open or shorted. | See SHIFT SOLENOIDS . |
| P1735 | First Gear Switch Circuit Failure | SS1 solenoid circuit failure, open or shorted. | See SHIFT SOLENOIDS . |
| P1736 | Second Gear Switch Circuit Failure | SS1 solenoid circuit failure, open or shorted. | See SHIFT SOLENOIDS . |
| P1737 | Lockup Solenoid | TCC solenoid failed. | See SHIFT SOLENOIDS . |
| P1738 | Shift Time Error | SS1 solenoid circuit failure, open or shorted. | See SHIFT SOLENOIDS . |
| P1741 | Torque Converter Clutch (TCC) Solenoid Control Error | TCC solenoid failed. | See SHIFT SOLENOIDS . |
| P1742 | Torque Converter Solenoid Circuit Short | TCC system malfunction (low slip). | See SHIFT SOLENOIDS . |
| P1743 | Torque Converter Clutch (TCC) Solenoid Circuit | TCC solenoid failed ON or OFF. | See SHIFT SOLENOIDS . |
| P1744 | Torque Converter Clutch (TCC) Solenoid Circuit | TCC system malfunction (excessive slip). | See SHIFT SOLENOIDS . |
| P1745 | Line Pressure Solenoid | EPC solenoid circuit failure, short circuit to VBAT. | See ELECTRONIC PRESSURE CONTROL (EPC) SOLENOID . |
| P1746 | Pressure Control Solenoid A Open Circuit | EPC solenoid circuit open. | See ELECTRONIC PRESSURE CONTROL (EPC) SOLENOID . |
| P1747 | Pressure Control Solenoid A Short Circuit | EPC solenoid circuit shorted. | See ELECTRONIC PRESSURE CONTROL (EPC) SOLENOID . |
| P1748 | Pressure Control Solenoid A | EPC solenoid circuit failure, short circuit to VBAT. | See ELECTRONIC PRESSURE CONTROL (EPC) SOLENOID . |
| P1751 | Shift Solenoid A Circuit Open | SS1 function failure. | See SHIFT SOLENOIDS . |
| P1752 | Shift Solenoid A Circuit Short | SS1 solenoid circuit failure, open or shorted. | See SHIFT SOLENOIDS . |
| P1756 | Shift Solenoid B Circuit Open | SS2 function failure. | See SHIFT SOLENOIDS . |
| P1757 | Shift Solenoid B Circuit Short | SS2 solenoid circuit failure, open or shorted. | See SHIFT SOLENOIDS . |
| P1760 | Pressure Control Solenoid A Short Circuit Intermittent | EPC solenoid circuit failure, shorted to ground. | See ELECTRONIC PRESSURE CONTROL (EPC) SOLENOID . |
| P1771 | Throttle Position (TP) Sensor Circuit High | TP out of range - high. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P1772 | Throttle Position Sensor Circuit Low | TP out of range - low. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P1775 | Torque Down Signal #1 Circuit | TCC solenoid failed. | See SHIFT SOLENOIDS . |
| P1776 | Torque Down Signal #2 Circuit | TCC solenoid failed. | See SHIFT SOLENOIDS . |
| P1777 | Torque Down Response Signal Circuit | TCC solenoid failed. | See SHIFT SOLENOIDS . |
| P1780 | Transaxle Control Switch (O/D Cancel) Circuit Out Of Self Test Range | Transaxle control switch not changing states during self-test. | Rerun self-test. Be sure to cycle overdrive switch during test. |
| P1783 | Transaxle Over Temperature Condition | Transaxle over temperature condition. | See TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR . |
| P1788 | Pressure Control Solenoid B Open Circuit | 3-2T/CCS solenoid circuit intermittent failures detected | See TIMING/COAST CLUTCH (2-3T/CCS) SOLENOID . |
| P1789 | Pressure Control Solenoid B Short Circuit | 3-2T/CCS solenoid circuit failure (short). | See TIMING/COAST CLUTCH (2-3T/CCS) SOLENOID . |
| P1791 | Throttle Position (TP) (Electric) Circuit | TP out of range. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P1792 | Barometer Pressure Circuit | BARO/MAP out of range | See MANIFOLD ABSOLUTE PRESSURE (MAP)SENSOR . |
| P1793 | Intake Air Volume Circuit | MAF malfunction. | See MASS AIR FLOW (MAF) SENSOR . |
| P1794 | Battery Voltage Circuit | Battery voltage out of acceptable parameters. | See SYMPTOM TROUBLESHOOTING CHART - CHARGING SYSTEM . |
| P1798 | Coolant Temperature Circuit | ECT malfunction. | See INTAKE AIR TEMPERATURE (IAT) SENSOR AND ENGINE COOLANT TEMPERATURE (ECT) SENSOR / CYLINDER HEAD TEMPERATURE (CHT) SENSOR . |
| P1824 | 4-Wheel Drive Clutch Relay Circuit Failure | 4-wheel drive clutch out of parameter. | CHECK SJB fuse 18 (10A). If fuse is good, see PINPOINT TEST 6: VEHICLE HAS NO OR INADEQUATE TORQUE AT REAR WHEELS . |
| P1825 | 4-Wheel Drive Clutch Relay Open Circuit | 4-wheel drive clutch out of parameter. | CHECK SJB fuse 18 (10A). If fuse is good, see PINPOINT TEST 6: VEHICLE HAS NO OR INADEQUATE TORQUE AT REAR WHEELS . |
| P1879 | Transfer Case Disengaged Solenoid Open Circuit | 3-2T/CCS solenoid circuit intermittent failures detected | See TIMING/COAST CLUTCH (2-3T/CCS) SOLENOID . |
| P1900 | Output Shaft Speed Sensor Circuit Intermittent | OSS sensor signal irregular or interrupted. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P1901 | Turbine Shaft Speed Sensor Circuit Intermittent | TSS sensor signal irregular or interrupted. | See TURBINE SHAFT SPEED (TSS) SENSOR AND OUTPUT SHAFT SPEED (OSS) SENSORS . |
| P2004 | Intake Manifold Runner Control Stuck Open (Bank 1) | IMTV commanded closed, but signal indicates open. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2005 | Intake Manifold Runner Control Stuck Open (Bank 2) | IMTV commanded closed, but signal indicates open. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2006 | Intake Manifold Runner Control Stuck Closed (Bank 1) | IMTV commanded open, but signal indicates closed. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2007 | Intake Manifold Runner Control Stuck Closed (Bank 2) | IMTV commanded open, but signal indicates closed. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2008 | Intake Manifold Runner Control Circuit / Open (Bank 1) | IMTV primary control circuit failure. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2009 | Intake Manifold Runner Control Circuit Low (Bank 1) | IMTV primary control circuit low voltage. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2010 | Intake Manifold Runner Control Circuit High (Bank 1) | IMTV primary control circuit voltage higher than calibrated value. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2011 | Intake Manifold Runner Control Circuit / Open (Bank 2) | IMTV primary control circuit failure. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2012 | Intake Manifold Runner Control Circuit Low (Bank 2) | IMTV primary control circuit low voltage. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2013 | Intake Manifold Runner Control Circuit High (Bank 2) | IMTV primary control circuit voltage higher than calibrated value. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2014 | Intake Manifold Runner Position Sensor/Switch Circuit (Bank 1) | IMTV signal outside of expected calibrated range. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2015 | Intake Manifold Runner Position Sensor/Switch Circuit Range/Perf. (Bank 1) | IMTV signal out of range. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2016 | Intake Manifold Runner Position Sensor/Switch Circuit Low (Bank 1) | IMTV circuit low voltage. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2017 | Intake Manifold Runner Position Sensor/Switch Circuit High (Bank 1) | IMTV circuit voltage high. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2018 | Intake Manifold Runner Position Sensor/Switch Circuit Intermittent (Bank 1) | IMTV circuit voltage intermittent. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2019 | Intake Manifold Runner Position Sensor/Switch Circuit (Bank 2) | IMTV signal outside of expected calibrated range. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2020 | Intake Manifold Runner Position Sensor/Switch Circuit Range/Perf. (Bank 2) | IMTV signal out of range. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2021 | Intake Manifold Runner Position Sensor/Switch Circuit Low (Bank 2) | IMTV circuit low voltage. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2022 | Intake Manifold Runner Position Sensor/Switch Circuit High (Bank 2) | IMTV circuit voltage high. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2023 | Intake Manifold Runner Position Sensor/Switch Circuit Intermittent (Bank 2) | IMTV circuit voltage intermittent. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2065 | Fuel Level Sensor B Circuit | Fuel level input (FLI) signal moves outside the minimum or maximum allowable calibrated parameters for a specified fuel fill percentage in the fuel tank. | See PINPOINT TEST 3: INCORRECT FUEL GAUGE INDICATION . |
| P2066 | Fuel Level Sensor B Circuit Range/Performance | Fuel level input noisy. | See TEST 3: INTERMITTENT . |
| P2067 | Fuel Level Sensor B Circuit Low | Fuel level input below calibrated minimum value. | See PINPOINT TEST 3: INCORRECT FUEL GAUGE INDICATION . |
| P2068 | Fuel Level Sensor B Circuit High | Fuel level input above calibrated maximum value. | See PINPOINT TEST 3: INCORRECT FUEL GAUGE INDICATION . |
| P2069 | Fuel Level Sensor B Circuit Intermittent | Fuel level input intermittent. | See TEST 3: INTERMITTENT . |
| P2070 | Intake Manifold Tuning Valve Stuck Open Bank 1 | IMTV signal outside of expected calibrated range. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2071 | Intake Manifold Tuning Valve Stuck Closed Bank 1 | IMTV signal outside of expected calibrated range. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2072 | Throttle Actuator Control System - Ice Breakage | Strategy has carried out several open and close cycles to remove potential ice build up. DTC does not imply any system concerns, only that the mode has occurred, and that the mode may be causing a long start time. | Check for possible ice, water or oil buildup in the positive crankcase ventilation (PCV) system. Repair as necessary. |
| P2073 | Manifold Absolute Pressure/Mass Air Flow (MAF) - Throttle Position (TP) Correlation at Idle | MAF higher/lower than expected for registered TP. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P2074 | Manifold Absolute Pressure/Mass Air Flow (MAF) - Throttle Position Correlation at Higher Load | MAF higher than expected for registered TP. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P2075 | Intake Manifold Tuning Valve Position Sensor/Switch Circuit (Bank 1) | IMTV signal outside of expected calibrated range. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2076 | Intake Manifold Tuning Valve Position Sensor/Switch Circuit Range/Performance (Bank 1) | IMTV signal out of range. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2077 | Intake Manifold Tuning Valve Position Sensor/Switch Circuit Low (Bank 1) | IMTV circuit low voltage. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2078 | Intake Manifold Tuning Valve Position Sensor/Switch Circuit High (Bank 1) | IMTV circuit voltage high. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2079 | Intake Manifold Tuning Valve Position Sensor/Switch Circuit Intermittent (Bank 1) | IMTV circuit voltage intermittent. | See INTAKE MANIFOLD RUNNER CONTROL (IMRC) SYSTEM . |
| P2096 | Post Catalyst Fuel Trim System Too Lean Bank 1 | Output voltage of the rear HO2S (Bank 1) fails to meet the calibrated limits. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P2097 | Post Catalyst Fuel Trim System Too Rich Bank 1 | Output voltage of the rear HO2S (Bank 1) high. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P2098 | Post Catalyst Fuel Trim System Too Lean Bank 2 | Output voltage of the rear HO2S (Bank 2) fails to meet the calibrated limits. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P2099 | Post Catalyst Fuel Trim System Too Rich Bank 2 | Output voltage of the rear HO2S (Bank 2) high. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P2121 | Throttle/Pedal Position Sensor D Circuit Range/Performance | Non-closed throttle position at idle. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P2122 | Throttle/Pedal Position Sensor D Circuit Low | TP sensor signal is less than Self-Test minimum of 0.17 volt (3.42%). | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P2123 | Throttle/Pedal Position Sensor D Circuit High | TP sensor signal is greater than Self-Test maximum of 4.65V (93%). | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P2124 | Throttle/Pedal Position Sensor D Intermittent | Powertrain control module (PCM) detected an intermittent concern with the TP sensor. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P2126 | Throttle/Pedal Position Sensor E Circuit Range/Performance | Non-closed throttle position at idle. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P2127 | Throttle/Pedal Position Sensor E Circuit Low | TP sensor signal is less than Self-Test minimum of 0.17 volt (3.42%). | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P2128 | Throttle/Pedal Position Sensor E Circuit High | TP sensor signal is greater than Self-Test maximum of 4.65V (93%). | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P2129 | Throttle/Pedal Position Sensor E Intermittent | Powertrain control module (PCM) detected an intermittent concern with the TP sensor. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P2131 | Throttle/Pedal Position Sensor F Circuit Range/Performance | Non-closed throttle position at idle. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P2132 | Throttle/Pedal Position Sensor F Circuit Low | TP sensor signal is less than Self-Test minimum of 0.17 volt (3.42%). | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P2133 | Throttle/Pedal Position Sensor F Circuit High | TP sensor signal is greater than Self-Test maximum of 4.65V (93%). | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P2134 | Throttle/Pedal Position Sensor F Intermittent | Powertrain control module (PCM) detected an intermittent concern with the TP sensor. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P2135 | Throttle/Pedal Position Sensor/Switch A / B Voltage Correlation | TP voltage out of expected range. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P2138 | Throttle/Pedal Position Sensor/Switch D / E Voltage Correlation | TP voltage out of expected range. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P2140 | Throttle/Pedal Position Sensor/Switch E / F Voltage Correlation | TP voltage out of expected range. | See THROTTLE POSITION (TP) SENSOR CIRCUIT MALFUNCTION . |
| P2144 | Exhaust Gas Recirculation Vent Control Circuit Low | The average voltage of the DPFEGR SIG circuit input is below minimum (0.2 V). | See EGR SYSTEM MALFUNCTION - 3.0L or EGR SYSTEM MALFUNCTION - 2.3L . |
| P2145 | Exhaust Gas Recirculation Vent Control Circuit High | The average voltage of the DPFEGR SIG circuit input is above maximum (4.5V). | See EGR SYSTEM MALFUNCTION - 3.0L or EGR SYSTEM MALFUNCTION - 2.3L . |
| P2177 | System Too Lean Off Idle - Bank 1 | HO2S sensor is indicating lean at the end of the test trying to correct for an over-rich condition. The test fails when the fuel control system no longer detects a switch for a calibrated amount of time. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P2178 | System Too Rich Off Idle - Bank 1 | HO2S sensor is indicating lean at the end of the test trying to correct for an over-rich condition. The test fails when the fuel control system no longer detects a switch for a calibrated amount of time. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P2179 | System Too Lean-Off Idle - Bank 2 | HO2S sensor is indicating lean at the end of the test trying to correct for an over-rich condition. The test fails when the fuel control system no longer detects a switch for a calibrated amount of time. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P2180 | System Too Rich Off Idle - Bank 2 | HO2S sensor is indicating lean at the end of the test trying to correct for an over-rich condition. The test fails when the fuel control system no longer detects a switch for a calibrated amount of time. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P2187 | System Too Lean Off Idle - Bank 1 | HO2S sensor is indicating lean at the end of the test trying to correct for an over-rich condition. The test fails when the fuel control system no longer detects a switch for a calibrated amount of time. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P2188 | System Too Rich Off Idle - Bank 1 | HO2S sensor is indicating lean at the end of the test trying to correct for an over-rich condition. The test fails when the fuel control system no longer detects a switch for a calibrated amount of time. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P2189 | System Too Lean Off Idle - Bank 2 | HO2S sensor is indicating lean at the end of the test trying to correct for an over-rich condition. The test fails when the fuel control system no longer detects a switch for a calibrated amount of time. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P2190 | System Too Rich Off Idle - Bank 2 | HO2S sensor is indicating lean at the end of the test trying to correct for an over-rich condition. The test fails when the fuel control system no longer detects a switch for a calibrated amount of time. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P2195 | Oxygen Sensor (HO2S) Signal Biased/Stuck Lean - Bank 1, Sensor 1 | HO2S sensor is indicating lean at the end of the test trying to correct for an over-rich condition. The test fails when the fuel control system no longer detects a switch for a calibrated amount of time. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P2196 | Oxygen Sensor (HO2S) Signal Biased/Stuck Rich - Bank 1, Sensor 1 | HO2S sensor is indicating rich at the end of the test trying to correct for an over-lean condition. The test fails when the fuel control system no longer detects a switch for a calibrated amount of time. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P2197 | Oxygen Sensor (HO2S) Signal Biased/Stuck Lean - Bank 2, Sensor 1 | HO2S sensor is indicating lean at the end of the test trying to correct for an over-rich condition. The test fails when the fuel control system no longer detects a switch for a calibrated amount of time. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P2198 | Oxygen Sensor (HO2S) Signal Biased/Stuck Rich - Bank 2, Sensor 1 | HO2S sensor is indicating rich at the end of the test trying to correct for an over-lean condition. The test fails when the fuel control system no longer detects a switch for a calibrated amount of time. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P2227 | Barometric Pressure Circuit Range/Performance | Manifold Absolute Pressure (MAP) sensor input to the powertrain control module (PCM) is not within the calibrated value. | See MANIFOLD ABSOLUTE PRESSURE (MAP)SENSOR . |
| P2228 | Barometric Pressure Circuit Low | MAP sensor operating voltage went below 0.25 volts. | See MANIFOLD ABSOLUTE PRESSURE (MAP)SENSOR . |
| P2229 | Barometric Pressure Circuit High | MAF/IAT signal went above 4.60 volts during engine operation or KOER Self-Test. | See MANIFOLD ABSOLUTE PRESSURE (MAP)SENSOR . |
| P2237 | Oxygen Sensor (HO2S) Positive Current Control Circuit / Open - Bank 1, Sensor 1 | HO2S circuit open. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P2245 | Oxygen Sensor (HO2S) Reference Voltage Circuit Low - Bank 1, Sensor 1 | HO2S circuit low voltage. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P2246 | Oxygen Sensor (HO2S) Reference Voltage Circuit High - Bank 1, Sensor 1 | HO2S circuit high voltage. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P2251 | Negative Current Control Circuit / Open - Bank 1, Sensor 1 | HO2S circuit open. | See UPSTREAM HEATED OXYGEN SENSOR (HO2S) NOT SWITCHING . |
| P2270 | Oxygen Sensor (HO2S) Signal Stuck Lean - Bank 1, Sensor 2 | The rear HO2S (Bank 1) is forced rich and lean by the powertrain control module (PCM). The test fails if the PCM does not detect the rich signal (P1157) or lean signal (P1158) during KOER Self-Test. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P2271 | Oxygen Sensor (HO2S) Signal Stuck Rich - Bank 1, Sensor 2 | The rear HO2S (Bank 1) is forced rich and lean by the powertrain control module (PCM). The test fails if the PCM does not detect the rich signal (P1157) or lean signal (P1158) during KOER Self-Test. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P2272 | Oxygen Sensor (HO2S) Signal Stuck Lean - Bank 2, Sensor 2 | The rear HO2S (Bank 2) is forced rich and lean by the powertrain control module (PCM). The test fails if the PCM does not detect the rich signal (P1157) or lean signal (P1158) during KOER Self-Test. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P2273 | Oxygen Sensor (HO2S) Signal Stuck Rich - Bank 2, Sensor 2 | The rear HO2S (Bank 2) is forced rich and lean by the powertrain control module (PCM). The test fails if the PCM does not detect the rich signal (P1157) or lean signal (P1158) during KOER Self-Test. | See DOWNSTREAM HEATED OXYGEN SENSOR (HO2S) . |
| P2500 | Generator Lamp Terminal Circuit Low | Generator/regulator system malfunction. | See SYMPTOM TROUBLESHOOTING CHART - CHARGING SYSTEM . |
| P2501 | Generator Lamp Terminal Circuit High | Generator/regulator system malfunction. | See SYMPTOM TROUBLESHOOTING CHART - CHARGING SYSTEM . |
| P2502 | Charging System Voltage | Generator/regulator system malfunction. | See GENERATOR/REGULATOR SYSTEM MALFUNCTION . |
| P2503 | Charging System Voltage Low | Generator/regulator system malfunction. | See GENERATOR/REGULATOR SYSTEM MALFUNCTION . |
| P2504 | Charging System Voltage High | Generator/regulator system malfunction. | See GENERATOR/REGULATOR SYSTEM MALFUNCTION . |
| P2507 | ECM / PCM Power Input Signal Low | Generator/regulator system malfunction. | See GENERATOR/REGULATOR SYSTEM MALFUNCTION . |