| CCNT_RCM (Number of continuous DTCs) |
- |
- DTCs detected: 1-255
- No DTCs detected: 0
|
- |
| DABAGR (Driver-side air bag module (inflator No.1) resistance) |
Ohm |
Under any condition: 1.5-3.7 ohms |
1S, 1V |
| D_ABAGR2 (Driver-side air bag module (inflator No.2) resistance) |
Ohm |
Under any condition: 1.5-3.7 ohms |
1G, 1J |
| DR_BUKL (Driver-side buckle switch status) |
Buckled/Unbuckled |
- Driver-side buckle switch on: Buckled
- Driver-side buckle switch off: Unbuckled
|
2T |
| DR_PTENS (Driver-side pre-tensioner seat belt resistance) |
Ohm |
Under any condition: 1.5-3.1 ohms |
2P, 2S |
| DS_AB (Driver-side side air bag module resistance) |
Ohm |
Under any condition: 1.4-3.2 ohms |
2M, 20 |
| DTC_CLR_ST (Seat weight sensor status) |
Starting/ Normal End/ In Process/ OCS Fault |
Fault information cleared at seat weight sensor |
1I |
| OCS_CAL_ST(Seat weight sensor calibration status) |
Starting/ Normal End/ Commanding/ NG(voltage)/ NG(weight)/ Timeout/ In Process OCS Fault |
- Seat weight sensor calibration start-up: Starting
- Seat weight sensor calibration completed normally: Normal End
- Seat weight sensor calibration command being sent: Commanding
- Voltage malfunction during seat weight sensor calibration: NG(voltage)
- Weight error during seat weight sensor calibration: NG(weight)
- Seat weight sensor calibration time limit passed: Timeout
- Seat weight sensor calibration being processed: In Process
- Seat weight sensor or seat weight sensor control module malfunction: OCS Fault
|
1I |
| OCS_FLT (Passenger sensing system status) |
MOD_Fail/ COMM_Fail/ CAL_Fail/ SNS_Fail/ SNS_Fail L/ SNS_Fail R/ BTS_Fail/ No_Fail |
- Seat weight sensor control module malfunction: MOD_Fail
- Seat weight sensor control module communication error: COMM_Fail
- Seat weight sensor calibration error: CAL_Fail
- Seat weight sensor malfunction: SNS_Fail
- Seat weight sensor (LH) malfunction: SNS_Fail_L
- Seat weight sensor (RH) malfunction: SNS_Fail_R
- Passenger-side front buckle switch malfunction: BTS_Fail
- Passenger sensing system is normal: No_Fail
|
1l |
| OCS_SYS_ST (Seat weight sensor status) |
Empty/ Indeterminate/ Small/ Large/ Invalid |
Occupant classification status determined by seat weight sensor |
11 |
| PABAGR (Passenger-side air bag module (inflator No.1) resistance) |
Ohm |
Under any condition: 1.4-2.9 ohms |
1M, 1P |
| P_ABAGR2 (Passenger-side air bag module (inflator No.2) resistance) |
Ohm |
Under any condition: 1.4-2.9 ohms |
1A, 1D |
| PS_AB (Passenger-side side air bag module resistance) |
Ohm |
Under any condition: 1.4-3.2 ohms |
2I, 2L |
| PS_BUKL (Passenger-side buckle switch status) |
Buckled/Unbuckled |
- Passenger-side buckle switch on: Buckled
- Passenger-side buckle switch off: Unbuckled
|
2H |
| PS_PTENS (Passenger-side pre-tensioner seat belt resistance) |
Ohm |
Under any condition: 1.5-3.1 ohms |
2G, 2J |
| PS_WEIGHT (Seat weight sensor measured weight of passenger) |
Kg |
Display of load (total seated weight) on passenger-side seat |
1I |
| PSAB_DepSt |
Inactive/Active |
- Passenger-side air bag module non-operation (non-deployment) status: Inactive
- Passenger-side air bag module operation (deployment) enabled status: Active
|
1I |
| RCM_VOLT (IG1 voltage) |
V |
Ignition switch is at ON: B+ |
1W |
| TRAK_SW (Seat track position sensor state) |
Forward/Rearward |
- Front seat front position: Forward
- Front seat rear position: Rearward
|
2W, 2X |