General Specifications - 3.0L
GENERAL SPECIFICATIONS - 3.0L
| Item | Specification |
|---|---|
| Displacement | 3.0L (4V) (182 CID) |
| No. cylinder | 6 |
| Bore/stroke | 89.0 x 79.5 mm (3.5 x 3.13 in) |
| Fire order | 1-4-2-5-3-6 |
| Oil pressure (Minimum at 1,500 rpm with engine warmed up after 10 minutes of idling.) | 76 kPa (11 psi) |
| Spark plug | AGSF-32M Gap = 1.30-1.40 mm (0.052-0.56 inch) |
| Cylinder Head and Valve Train | |
| Cylinder head gasket surface flatness | - |
| Combustion chamber volume | 52 cc (3.17 CI) |
| Valve arrangement (front to rear) | LH intake I-I-I-I-I-I LH exhaust E-E-E-E-E-E RH intake I-I-I-I-I-I RH exhaust E-E-E-E-E-E |
| Valve guide bore diameter | 6.015-6.044 mm (0.236-0.237 in) |
| Valve stem diameter - intake | 5.975-5.995 mm (0.2350-0.2358 in) |
| Valve stem diameter - exhaust | 5.950-5.970 mm (0.2343-0.2350 in) |
| Valve stem-to-guide clearance - intake | 0.019-0.069 mm (0.0007-0.0027 in) |
| Valve stem-to-guide clearance - exhaust | 0,045-0.094 mm (0.0017-0.037 in) |
| Valve head diameter - intake | 35 mm (1.38 in) |
| Valve head diameter - exhaust | 30 mm (1.18 in) |
| Valve head diameter (intake) - gauge diameter | 33.5 mm (1.3189 in) |
| Valve head diameter (exhaust) - gauge diameter | 28.0 mm (1.10236 in) |
| Valve face runout | 0.05 mm (0.001 in) |
| Valve face angle | 45.5 degrees |
| Valve seat width - intake | 1.1-1.4 mm (0.043-0.055 in) |
| Valve seat width - exhaust | 1.4-1.7 mm (0.055-0.066 in) |
| Valve seat runout | 0.04 mm (0.001 in) |
| Valve seat angle | 44.75 degrees |
| Valve spring free length (approx.) | 46.6 mm (1.84 in) |
| Valve spring squareness | 2.5% |
| Valve spring compression pressure (N @ spec. length) | 693 N @ 30.09 mm (156 lbs @ 1.18 in) |
| Valve spring installed height (N @ spec. length) | 39.89 mm (1.57 in) |
| Valve spring installed pressure | 240 N @ 39.89 mm (53.95 lbs @ 1.57 in) |
| Valve spring installed pressure - service limit | 10% force loss @ specified height |
| Roller follower ratio @ max. lift | 2.0:1 |
| Hydraulic Lash Adjuster | |
| Diameter (standard) | 16-15.988 mm (0.6299-0.6294 in) |
| Clearance-to-bore | 0.018-0.069 mm (0.0007-0.0027 in) |
| Hydraulic leakdown rate | 5-25 seconds |
| Collapsed lash adjuster gap | 0.50-1.11 mm (0.019-0.043 in) |
| Camshaft | |
| Theoretical valve lift @ 0 lash | 9.80 mm (0.386 in) |
| Lobe lift | 4.80 mm (0.189 in) |
| Allowable lobe lift loss | 0.76 mm (0.003 in) |
| Journal diameter (all) | 26.962-26.936 mm (1.061-1.060 in) |
| Camshaft journal bore inside diameter | 27.012-26.987 mm (1.063-1.062 in) |
| Camshaft journal-to-bearing clearance - standard | 0.025-0.076 mm (0.001-0.0029 in) |
| Camshaft journal-to-bearing clearance - service limit | 0.121 mm (0.0047 in) |
| Runout | - |
| End play - service limit | 0.190 mm (0.00748 in) |