LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 1997 >> MX-6 Base, Standard >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> 2.0L 4-CYL >> Torque Specifications

Torque Specifications

TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
Camshaft Sprocket Bolt 37-44 (50-60)
Clutch Pressure Plate Bolt 13-19 (18-26)
Compressor Bracket-To-Compressor 18-26 (24-35)
Connecting Rod Cap Bolt
Step 1 16-20 (22-27)
Step 2 (Final) Additional 82.5-97.5 Degrees
Coolant Outlet Bolt 14-18 (19-25)
Crankshaft Sprocket Bolt 116-122 (157-165)
Cylinder Head Bolt (1)
Step 1 13-16 (18-22)
Step 2 Additional 85-95 Degrees
Step 3 (Final) Additional 85-95 Degrees
Distributor Bolt (1997 Models) 14-18 (19-25)
Engine Mount-To-Frame Nut 50-68 (67-93)
Exhaust Header Pipe-To-Exhaust Manifold Nut 28-38 (38-51)
Exhaust Manifold
Bolt 12-16 (16-22)
Nut 15-20 (20-28)
Flywheel/Drive Plate Bolt 71-76 (97-102)
Front Cover/Oil Pump Bolt 14-18 (19-25)
Generator Top Bolt 28-38 (38-51)
Intake Manifold Bolt/Nut 14-18 (19-25)
Intake Manifold Support Bracket 28-38 (38-51)
Main Bearing Cap Bolt
Step 1 13-16 (17-22)
Step 2 (Final) Additional 85-95 Degrees
Motor Mount Bolt 63-86 (86-116)
Motor Mount-To-Engine Bolt/Nut 50-68 (67-93)
Oil Pan Bolt 14-18 (19-25)
Oil Pan Upper Block Bolt/Nut (2)
Power Steering Pump
Upper Bolt 32-44 (44-60)
Lower Bolt 24-34 (32-46)
Spark Plug 11-16 (15-22)
Thermostat Housing Bolt 14-18 (19-25)
Timing Belt Idler Pulley Bolt 28-38 (38-51)
Timing Belt Tensioner Lock Bolt 28-38 (38-51)
Water Pump Bolt 14-18 (19-25)
INCH Lbs. (N.m) 
Camshaft Bearing Cap Bolt 100-125 (11-14)
Oil Pressure Switch 105-156 (12-18)
Oil Pump Cover Screws 53-78 (6-9)
Oil Strainer Bolt (3) 70-95 (8-11)
Rear Cover Bolt 70-95 (8-11)
Timing Belt Cover Bolt 70-95 (8-11)
Valve Cover Bolt (4) 53-70 (6-8)
Water Pump Pulley Bolt 70-95 (8-11)
(1) Tighten in sequence. See Figure and Figure .
(2) Tighten 2 nuts at rear end of cylinder block to 70-95 INCH lbs. (8-11 N.m). Tighten oil pan upper block bolts in 2-3 steps, in proper sequence to 14-18 ft. lbs. (19-25 N.m). See Figure and Figure .
(3) Tighten flange bolts, then tighten bracket bolt.
(4) Tighten in sequence. See Figure and Figure .