LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 1996 >> Millenia Base >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> 2.5L V6 Code [KL] >> Torque Specifications

Torque Specifications

TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
A/C Compressor Bracket Bolt 28-38 (38-52)
Axle Shaft Bracket-To-Cylinder Block Bolt 32-46 (43-62)
Baffle Plate Bolt 14-18 (19-25)
Camshaft Sprocket Bolt 90-103 (122-140)
Clutch Release Cylinder Bolt (M/T) 12-17 (16-23)
Connecting Rod Bolt
Step 1 16-20 (22-27)
Step 2 Additional 83-97 Degrees
Coolant Outlet Bolt 14-18 (19-25)
Crankshaft Pulley Bolt 116-122 (157-166)
Cylinder Head Bolt (1)
Step 1 17-19 (23-26)
Step 2 Additional 85-95 Degrees
Step 3 Additional 85-95 Degrees
Engine Mount Bracket Above Water Pump-To-Cylinder Block Bolt 32-45 (43-61)
Engine Mount Crossmember Retaining Bolt/Nut 50-69 (68-93)
Engine Mount-To-Engine Mount Crossmember Nut 55-77 (75-104)
Engine Mount-To-Transaxle Case Nut 27-38 (37-52)
Engine-To-Transaxle Case Bolt 66-86 (90-116)
Exhaust Manifold Bolt/Nut 12-16 (16-22)
Flywheel/Flexplate Bolt 45-49 (61-67)
Friction Gear Nut 51-57 (69-78)
Front Exhaust Pipe-To-Exhaust Manifold Nut 28-38 (38-52)
Front Suspension Crossmember Bolt 69-97 (94-131)
Fuel Rail Bolt 14-18 (19-25)
Intake Manifold Bolt/Nut 14-18 (19-25)
Knock Sensor 15-25 (20-34)
Lower Control Arm Ball Joint To-Steering Knuckle Through-Bolt 32-43 (43-58)
Lower Cylinder Block Bolt (2)
Bolt "A"
Step 1 17-19 (23-26)
Step 2 Additional 75-85 Degrees
Bolt "B"
Step 1 17-19 (23-26)
Step 2 Additional 65-75 Degrees
Bolt "C"
Step 1 13-15 (18-20)
Step 2 Additional 55-65 Degrees
Bolt "D" 14-18 (19-25)
No. 1 Idler Pulley Bolt 28-38 (38-51)
No. 2 Idler Pulley Bolt 28-38 (38-51)
Oil Cooler-To-Oil Filter Adapter Nut 19-25 (25-34)
Oil Pan Bolt
Long Bolt 14-18 (19-25)
Short Bolt (3)
Oil Pump Bolt 14-18 (19-25)
Power Steering Pump Bracket Bolt (4)
Power Steering Pump Pulley Nut 37-43 (52-58)
Relief Valve Plug 42-50 (57-68)
Right (Timing Belt Side) Engine Mount
Nut 55-75 (74-102)
Through-Bolt 63-86 (86-116)
Shift Rod-To-Transaxle Bolt (M/T) 12-17 (16-23)
Spark Plug 11-16 (15-22)
Stabilizer Bar Link Nut 32-45 (43-61)
Stabilizer Rod-To-Transaxle Bolt (M/T) 23-34 (31-46)
Starter-To-Transaxle Case Bolt 24-34 (32-46)
Tensioner Pulley Bolt 28-32 (38-44)
Throttle Body Bolt/Nut 14-18 (19-25)
Tie Rod End Nut 41-59 (55-80)
Timing Belt Tensioner Bolt 14-18 (19-25)
Transaxle Mount & Bracket Bolt/Nut 50-68 (67-92)
Water Pump Bolt 14-18 (19-25)
Wheel Lug Nut 65-87 (88-118)
INCH Lbs. (N.m) 
Air Pipe-To-Intake Manifold Bolt 71-97 (8-11)
Camshaft Bearing Cap Bolt (5) 97-124 (11-14)
Crankshaft Position Sensor Bracket Bolt 71-97 (8-11)
Cylinder Block Valley Cover Bolt 71-97 (8-11)
Fuel Injector Retainer Bolt 18-35 (2-4)
Oil Jet 27-45 (3-5)
Oil Pump Body Cover Bolt 54-80 (6-9)
Pick-Up Tube Bolt 71-97 (8-11)
Pressure Regulator Bolt 62-89 (7-10)
Seal Plate Bolt 71-97 (8-11)
Timing Belt Cover Bolt 71-97 (8-11)
Valve Cover Bolt (6) 45-80 (5-9)
Water Pump Pulley Bolt 71-97 (8-11)
(1) Tighten bolts to specification in sequence. See Figure.
(2) Identify bolts and tighten bolts to specification in proper sequence. See Figure.
(3) Tighten bolts to 71-97 INCH lbs. (8-11 N.m).
(4) Tighten 2 upper bolts on front of bracket to 23-34 ft. lbs. (31-46 N.m). Tighten lower bolt on front of bracket to 14-19 ft. lbs. (19-26 N.m). Tighten bolt on rear of bracket-to-cylinder block to 24-33 ft. lbs. (32-45 N.m).
(5) Tighten bolts to specification in sequence. See Figure.
(6) Tighten bolts to specification in sequence. See Figure.