LEMON Manuals: Even more car manuals for everyone
Home >> Lincoln >> 2024 >> Navigator Reserve >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Engine >> Removal And Installation >> Engine Mount RH >> Installation

Engine Mount RH: Installation

  1. Clean the engine mount-to-cylinder block and engine mount-to-frame mating surfaces of any dirt or foreign material prior to installation.
    GFD882925Courtesy of FORD MOTOR COMPANY
  2. Position the RH engine mount into the vehicle.
    GFD882924Courtesy of FORD MOTOR COMPANY
  3. Position the RH engine mount-to-cylinder block bracket and install the new bolts in the sequence shown below.

    Torque: 77 Nm

    Fig 1: Engine Mount RH to Cylinder Block Tightening Sequence
    GFD882926Courtesy of FORD MOTOR COMPANY
  4. NOTE: Only use hand tools when installing the engine mount studs or damage to the engine mount can occur.
    NOTE: Apply threadlock to the stud threads prior to installation.

    Install the RH engine mount studs.

    Material: Thread Locking Adhesive (WSK-M2G351-A6)

    Torque: 30 Nm

    GFD882927Courtesy of FORD MOTOR COMPANY
  5. NOTE: Only use hand tools when installing the RH engine mount nuts or damage to the engine mount can occur.

    Install the new RH engine mount nuts.

    Torque: 150 Nm

    GFD882928Courtesy of FORD MOTOR COMPANY
  6. Lower the engine to the installed position.
    GFD882911Courtesy of FORD MOTOR COMPANY
  7. NOTE: Only use hand tools when loosening or tightening the engine mount through bolts or damage to the engine mount-to-cylinder block bracket can occur.

    Install the new LH engine mount through bolt.

    Torque: 350 Nm

    GFD882912Courtesy of FORD MOTOR COMPANY
  8. NOTE: Only use hand tools when loosening or tightening the engine mount through bolts or damage to the engine mount-to-cylinder block bracket can occur.

    Install the new RH engine mount through bolt.

    Torque: 350 Nm

    GFD882913Courtesy of FORD MOTOR COMPANY
  9. Position back the A/C compressor and install the bolts.

    Torque: 25 Nm

    GFD882921Courtesy of FORD MOTOR COMPANY
  10. Connect the A/C compressor electrical connectors and wire retainer.
    GFD882920Courtesy of FORD MOTOR COMPANY
  11. Position back the coolant pump and install the bolts. Connect the coolant pump electrical connector.

    Torque: 7 Nm

    GFD882919Courtesy of FORD MOTOR COMPANY
  12. Install the following items:

    1. Install the A/C compressor belt. Refer to: Air Conditioning (A/C) Compressor Belt .
    2. Install the starter motor. Refer to: Starter Motor .

  13. NOTE: Only use hand tools when loosening or tightening the transmission mount-to-crossmember nuts or damage to the transmission mount can occur.

    Remove and discard the transmission mount-to-crossmember nuts. Install new transmission mount-to-crossmember nuts.

    Torque: 115 Nm

    GFD882881Courtesy of FORD MOTOR COMPANY
  14. Install the new RH catalytic converter-to-turbocharger nuts.

    Torque: 40 Nm

    GFD882914Courtesy of FORD MOTOR COMPANY
  15. Install the new LH catalytic converter-to-turbocharger nuts.

    Torque: 40 Nm

    GFD882915Courtesy of FORD MOTOR COMPANY
  16. If equipped. Install the front driveshaft. Refer to: Front Driveshaft .
    • Install the underbody shield and the bolts.

      Torque: 40 Nm

    • Install the underbody shield and the bolts

      Torque: 8 Nm

    GFD882916Courtesy of FORD MOTOR COMPANY
    • Install the transmission housing cover and attach the bolts.

      Torque: 8 Nm

    GFD882877Courtesy of FORD MOTOR COMPANY
  19. Remove the special tools. Remove Special Service Tool: 303-F070 Support Bar, Engine., 303-1246 Engine Spreader Bar., 303-1654 Lift Eyes.
    GFD882876Courtesy of FORD MOTOR COMPANY
  20. Install the air deflector and pin-type retainers.
    GFD882873Courtesy of FORD MOTOR COMPANY
  21. Install the air cleaner inlet tube, pin-type retainers and bolt.
    GFD882872Courtesy of FORD MOTOR COMPANY
  22. NOTE: Align the index marks made during hinge removal.

    On Both sides.

    • Install the hood hinge and bolts.

      Torque: 30 Nm

    • Install the fender to hood hinge bolts.

      Torque: 9 Nm

    GFD882917Courtesy of FORD MOTOR COMPANY
  23. Install the struts.
    GFD882870Courtesy of FORD MOTOR COMPANY
  24. NOTE: Align the index marks made during hood removal.

    Position the hood and install the nuts.

    Torque: 25 Nm

    GFD882869Courtesy of FORD MOTOR COMPANY
  25. Install the right rear ignition coil. Refer to: Ignition Coil-On-Plug .
  26. Install the intake manifold. Refer to: Intake Manifold .
  27. Position back the CAC tube bracket and install the nuts.

    Torque: 6 Nm

    GFD882918Courtesy of FORD MOTOR COMPANY
  28. Install the CAC outlet pipe. Refer to: Charge Air Cooler (CAC) Outlet Pipe .
  29. Install the CAC intake pipe. Refer to: Charge Air Cooler (CAC) Intake Pipe .
  30. Install the cowl panel. Refer to: Cowl Panel .
  31. Slide the engine appearance cover into the retaining bracket and install the retainers.

    Torque: 11 Nm

    GFD882871Courtesy of FORD MOTOR COMPANY
  32. Start and check the exhaust system for leaks.
scientia non olet · About LEMON Manuals