| BCM |
B10AB:00 |
Remote Keyless Entry Synchronization: No Sub Type Information |
GO to Pinpoint Test O |
| BCM |
B10C6:01 |
Exterior Trunk Antenna: General Circuit/Electrical Failure |
GO to Pinpoint Test U |
| BCM |
B10C7:01 |
Interior Trunk Antenna: General Circuit/Electrical Failure |
GO to Pinpoint Test T |
| BCM |
B1218:00 |
Transmitter Identification Code: No Sub Type Information |
GO to Pinpoint Test O |
| BCM |
B1336:01 |
Left Front Door External Antenna: General Circuit/Electrical Failure |
GO to Pinpoint Test S |
| BCM |
B1337:01 |
Right Front Door External Antenna: General Circuit/Electrical Failure |
GO to Pinpoint Test S |
| BCM |
B1381:11 |
Left Front Door Handle Proximity Sensor: Circuit Short To Ground |
GO to Pinpoint Test S |
| BCM |
B1381:15 |
Left Front Door Handle Proximity Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test S |
| BCM |
B1381:29 |
Left Front Door Handle Proximity Sensor: Signal Invalid |
GO to Pinpoint Test S |
| BCM |
B1382:11 |
Right Front Door Handle Proximity Sensor: Circuit Short To Ground |
GO to Pinpoint Test S |
| BCM |
B1382:15 |
Right Front Door Handle Proximity Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test S |
| BCM |
B1382:29 |
Right Front Door Handle Proximity Sensor: Signal Invalid |
GO to Pinpoint Test S |
| BCM |
B1383:11 |
Left Rear Door Handle Proximity Sensor: Circuit Short To Ground |
GO to Pinpoint Test S |
| BCM |
B1383:15 |
Left Rear Door Handle Proximity Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test S |
| BCM |
B1383:29 |
Left Rear Door Handle Proximity Sensor: Signal Invalid |
GO to Pinpoint Test S |
| BCM |
B1384:11 |
Right Rear Door Handle Proximity Sensor: Circuit Short To Ground |
GO to Pinpoint Test S |
| BCM |
B1384:15 |
Right Rear Door Handle Proximity Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test S |
| BCM |
B1384:29 |
Right Rear Door Handle Proximity Sensor: Signal Invalid |
GO to Pinpoint Test S |
| BCM |
B14B8:11 |
Sounder: Circuit Short To Ground |
GO to Pinpoint Test L |
| BCM |
B14B8:15 |
Sounder: Circuit Short To Battery Or Open |
GO to Pinpoint Test L |
| BCM |
B14B8:15 |
Sounder: Circuit Short To Battery Or Open |
GO to Pinpoint Test M |
| BCM |
B1560:49 |
Driver Side Keypad: Internal Electronic Failure |
GO to Pinpoint Test N |
| BCM |
B1561:49 |
Passenger Side Keypad: Internal Electronic Failure |
GO to Pinpoint Test N |
| BCM |
U0258:87 |
Lost Communication With Radio Transceiver: Missing Message |
GO to Pinpoint Test V |
| DCME |
B1519:12 |
Exterior Door Unlatch Switch: Circuit Short To Battery |
GO to Pinpoint Test F |
| DCME |
B1519:14 |
Exterior Door Unlatch Switch: Circuit Short To Ground Or Open |
GO to Pinpoint Test F |
| DCME |
B1519:92 |
Exterior Door Unlatch Switch: Performance Or Incorrect Operation |
GO to Pinpoint Test F |
| DCME |
B1519:9E |
Exterior Door Unlatch Switch: Stuck On |
GO to Pinpoint Test F |
| DCME |
U0100:00 |
Lost Communication With ECM/PCM 'A': No Sub Type Information |
GO to Pinpoint Test Z |
| DCME |
U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test AA |
| DCME |
U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test AB |
| DCME |
U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test AJ |
| DCME |
U1000:00 |
Solid State Driver Protection Active -Driver Disabled: No Sub Type Information |
GO to Pinpoint Test AM |
| DCME |
U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AK |
| DCME |
U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test AK |
| DCME |
U211A:46 |
Trusted Real-Time Operational Network (TRON) Configuration: Calibration/Parameter Memory Failure |
GO to Pinpoint Test AK |
| DCME |
U211B:05 |
Control Module Message Authentication: System Programming Failure |
GO to Pinpoint Test AK |
| DCME |
U211B:08 |
Control Module Message Authentication: Bus Signal / Message Failure |
GO to Pinpoint Test AK |
| DCME |
U211B:43 |
Control Module Message Authentication: Special Memory Failure |
GO to Pinpoint Test AK |
| DCME |
U211B:51 |
Control Module Message Authentication: Not Programmed |
GO to Pinpoint Test AK |
| DCME |
U211B:81 |
Control Module Message Authentication: Invalid Serial Data Received |
GO to Pinpoint Test AK |
| DCME |
U211B:87 |
Control Module Message Authentication: Missing Message |
GO to Pinpoint Test AK |
| DCME |
U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test AK |
| DCME |
U3000:01 |
Control Module: General Circuit/Electrical Failure |
GO to Pinpoint Test AL |
| DCME |
U3000:11 |
Control Module: Circuit Short To Ground |
GO to Pinpoint Test AL |
| DCME |
U3000:13 |
Control Module: Circuit Open |
GO to Pinpoint Test AL |
| DCME |
U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AL |
| DCME |
U3000:77 |
Control Module: Commanded Position Not Reachable |
GO to Pinpoint Test AL |
| DCME |
U3000:91 |
Control Module: Parametric |
GO to Pinpoint Test AL |
| DCMF |
B1519:12 |
Exterior Door Unlatch Switch: Circuit Short To Battery |
GO to Pinpoint Test F |
| DCMF |
B1519:14 |
Exterior Door Unlatch Switch: Circuit Short To Ground Or Open |
GO to Pinpoint Test F |
| DCMF |
B1519:92 |
Exterior Door Unlatch Switch: Performance Or Incorrect Operation |
GO to Pinpoint Test F |
| DCMF |
B1519:9E |
Exterior Door Unlatch Switch: Stuck On |
GO to Pinpoint Test F |
| DCMF |
U0100:00 |
Lost Communication With ECM/PCM 'A': No Sub Type Information |
GO to Pinpoint Test Z |
| DCMF |
U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test AA |
| DCMF |
U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test AB |
| DCMF |
U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test AJ |
| DCMF |
U1000:00 |
Solid State Driver Protection Active -Driver Disabled: No Sub Type Information |
GO to Pinpoint Test AM |
| DCMF |
U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AK |
| DCMF |
U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test AK |
| DCMF |
U211A:46 |
Trusted Real-Time Operational Network (TRON) Configuration: Calibration/Parameter Memory Failure |
GO to Pinpoint Test AK |
| DCMF |
U211B:05 |
Control Module Message Authentication: System Programming Failure |
GO to Pinpoint Test AK |
| DCMF |
U211B:08 |
Control Module Message Authentication: Bus Signal / Message Failure |
GO to Pinpoint Test AK |
| DCMF |
U211B:43 |
Control Module Message Authentication: Special Memory Failure |
GO to Pinpoint Test AK |
| DCMF |
U211B:51 |
Control Module Message Authentication: Not Programmed |
GO to Pinpoint Test AK |
| DCMF |
U211B:81 |
Control Module Message Authentication: Invalid Serial Data Received |
GO to Pinpoint Test AK |
| DCMF |
U211B:87 |
Control Module Message Authentication: Missing Message |
GO to Pinpoint Test AK |
| DCMF |
U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test AK |
| DCMF |
U3000:01 |
Control Module: General Circuit/Electrical Failure |
GO to Pinpoint Test AL |
| DCMF |
U3000:11 |
Control Module: Circuit Short To Ground |
GO to Pinpoint Test AL |
| DCMF |
U3000:13 |
Control Module: Circuit Open |
GO to Pinpoint Test AL |
| DCMF |
U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AL |
| DCMF |
U3000:77 |
Control Module: Commanded Position Not Reachable |
GO to Pinpoint Test AL |
| DCMF |
U3000:91 |
Control Module: Parametric |
GO to Pinpoint Test AL |
| DCMG |
B1519:12 |
Exterior Door Unlatch Switch: Circuit Short To Battery |
GO to Pinpoint Test F |
| DCMG |
B1519:14 |
Exterior Door Unlatch Switch: Circuit Short To Ground Or Open |
GO to Pinpoint Test F |
| DCMG |
B1519:92 |
Exterior Door Unlatch Switch: Performance Or Incorrect Operation |
GO to Pinpoint Test F |
| DCMG |
B1519:9E |
Exterior Door Unlatch Switch: Stuck On |
GO to Pinpoint Test F |
| DCMG |
U0100:00 |
Lost Communication With ECM/PCM 'A': No Sub Type Information |
GO to Pinpoint Test Z |
| DCMG |
U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test AA |
| DCMG |
U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test AB |
| DCMG |
U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test AJ |
| DCMG |
U1000:00 |
Solid State Driver Protection Active -Driver Disabled: No Sub Type Information |
GO to Pinpoint Test AM |
| DCMG |
U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AK |
| DCMG |
U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test AK |
| DCMG |
U211A:46 |
Trusted Real-Time Operational Network (TRON) Configuration: Calibration/Parameter Memory Failure |
GO to Pinpoint Test AK |
| DCMG |
U211B:05 |
Control Module Message Authentication: System Programming Failure |
GO to Pinpoint Test AK |
| DCMG |
U211B:08 |
Control Module Message Authentication: Bus Signal / Message Failure |
GO to Pinpoint Test AK |
| DCMG |
U211B:43 |
Control Module Message Authentication: Special Memory Failure |
GO to Pinpoint Test AK |
| DCMG |
U211B:51 |
Control Module Message Authentication: Not Programmed |
GO to Pinpoint Test AK |
| DCMG |
U211B:81 |
Control Module Message Authentication: Invalid Serial Data Received |
GO to Pinpoint Test AK |
| DCMG |
U211B:87 |
Control Module Message Authentication: Missing Message |
GO to Pinpoint Test AK |
| DCMG |
U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test AK |
| DCMG |
U3000:01 |
Control Module: General Circuit/Electrical Failure |
GO to Pinpoint Test AL |
| DCMG |
U3000:11 |
Control Module: Circuit Short To Ground |
GO to Pinpoint Test AL |
| DCMG |
U3000:13 |
Control Module: Circuit Open |
GO to Pinpoint Test AL |
| DCMG |
U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AL |
| DCMG |
U3000:77 |
Control Module: Commanded Position Not Reachable |
GO to Pinpoint Test AL |
| DCMG |
U3000:91 |
Control Module: Parametric |
GO to Pinpoint Test AL |
| DCMH |
B1519:12 |
Exterior Door Unlatch Switch: Circuit Short To Battery |
GO to Pinpoint Test F |
| DCMH |
B1519:14 |
Exterior Door Unlatch Switch: Circuit Short To Ground Or Open |
GO to Pinpoint Test F |
| DCMH |
B1519:92 |
Exterior Door Unlatch Switch: Performance Or Incorrect Operation |
GO to Pinpoint Test F |
| DCMH |
B1519:9E |
Exterior Door Unlatch Switch: Stuck On |
GO to Pinpoint Test F |
| DCMH |
U0100:00 |
Lost Communication With ECM/PCM 'A': No Sub Type Information |
GO to Pinpoint Test Z |
| DCMH |
U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test AA |
| DCMH |
U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test AB |
| DCMH |
U0431:00 |
Invalid Data Received From Body Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AJ |
| DCMH |
U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test AJ |
| DCMH |
U1000:00 |
Solid State Driver Protection Active -Driver Disabled: No Sub Type Information |
GO to Pinpoint Test AM |
| DCMH |
U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AK |
| DCMH |
U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test AK |
| DCMH |
U211A:46 |
Trusted Real-Time Operational Network (TRON) Configuration: Calibration/Parameter Memory Failure |
GO to Pinpoint Test AK |
| DCMH |
U211B:05 |
Control Module Message Authentication: System Programming Failure |
GO to Pinpoint Test AK |
| DCMH |
U211B:08 |
Control Module Message Authentication: Bus Signal / Message Failure |
GO to Pinpoint Test AK |
| DCMH |
U211B:43 |
Control Module Message Authentication: Special Memory Failure |
GO to Pinpoint Test AK |
| DCMH |
U211B:51 |
Control Module Message Authentication: Not Programmed |
GO to Pinpoint Test AK |
| DCMH |
U211B:81 |
Control Module Message Authentication: Invalid Serial Data Received |
GO to Pinpoint Test AK |
| DCMH |
U211B:87 |
Control Module Message Authentication: Missing Message |
GO to Pinpoint Test AK |
| DCMH |
U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test AK |
| DCMH |
U3000:01 |
Control Module: General Circuit/Electrical Failure |
GO to Pinpoint Test AL |
| DCMH |
U3000:11 |
Control Module: Circuit Short To Ground |
GO to Pinpoint Test AL |
| DCMH |
U3000:13 |
Control Module: Circuit Open |
GO to Pinpoint Test AL |
| DCMH |
U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AL |
| DCMH |
U3000:77 |
Control Module: Commanded Position Not Reachable |
GO to Pinpoint Test AL |
| DCMH |
U3000:91 |
Control Module: Parametric |
GO to Pinpoint Test AL |
| DDM |
B108F:23 |
Cabin Lock/Unlock Switch: Signal Stuck Low |
GO to Pinpoint Test G |
| DDM |
B1142:29 |
Ignition Status 1: Signal Invalid |
GO to Pinpoint Test Y |
| DDM |
B1142:86 |
Ignition Status 1: Signal Invalid |
GO to Pinpoint Test Y |
| DDM |
B12BA:11 |
Lock Status LED - Front: Circuit Short To Ground |
GO to Pinpoint Test H |
| DDM |
U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test AA |
| DDM |
U0164:00 |
Lost Communication With HVAC Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AC |
| DDM |
U0208:00 |
Lost Communication With Seat Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AD |
| DDM |
U0232:00 |
Lost Communication With Side Obstacle Detection Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AE |
| DDM |
U0294:00 |
Lost Communication With Powertrain Control Monitor Module: No Sub Type Information |
GO to Pinpoint Test AG |
| DDM |
U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test AJ |
| DDM |
U0509:00 |
Invalid Data Received From Seat Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AJ |
| DDM |
U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AK |
| DDM |
U211B:05 |
Control Module Message Authentication: System Programming Failure |
GO to Pinpoint Test AK |
| DDM |
U211B:08 |
Control Module Message Authentication: Bus Signal / Message Failure |
GO to Pinpoint Test AK |
| DDM |
U211B:43 |
Control Module Message Authentication: Special Memory Failure |
GO to Pinpoint Test AK |
| DDM |
U211B:51 |
Control Module Message Authentication: Not Programmed |
GO to Pinpoint Test AK |
| DDM |
U211B:81 |
Control Module Message Authentication: Invalid Serial Data Received |
GO to Pinpoint Test AK |
| DDM |
U211B:87 |
Control Module Message Authentication: Missing Message |
GO to Pinpoint Test AK |
| DDM |
U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test AK |
| DDM |
U3000:04 |
Control Module: System Internal Failure |
GO to Pinpoint Test AL |
| DDM |
U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AL |
| DDM |
U3000:4B |
Control Module: Over Temperature |
GO to Pinpoint Test AL |
| DDM |
U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test AH |
| DDM |
U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test AI |
| PCM |
P04B5:00 |
Fuel Fill Door Stuck Open: No Sub Type Information |
GO to Pinpoint Test W |
| PCM |
P04BA:00 |
Fuel Fill Door Position Sensor/Switch Circuit High: No Sub Type Information |
GO to Pinpoint Test W |
| PCM |
P04C1:00 |
Fuel Fill Door Unlock Control Circuit Low: No Sub Type Information |
GO to Pinpoint Test J |
| PCM |
P04C2:00 |
Fuel Fill Door Unlock Control Circuit High: No Sub Type Information |
GO to Pinpoint Test I |
| PCM |
P04C9:00 |
Fuel Fill Door Open Request Sensor/Switch Performance/Stuck Off: No Sub Type Information |
GO to Pinpoint Test I |
| PCM |
P04CA:00 |
Fuel Fill Door Open Request Sensor/Switch Circuit Low: No Sub Type Information |
GO to Pinpoint Test I |
| PCM |
P04CB:00 |
Fuel Fill Door Open Request Sensor/Switch Circuit High: No Sub Type Information |
GO to Pinpoint Test I |
| PCM |
P04CD:00 |
Fuel Fill Door Open Request Sensor/Switch Stuck On: No Sub Type Information |
GO to Pinpoint Test I |
| PCM |
P1594:00 |
Forced Engine Shutdown - Remote Start System Fault, No Unattended Vehicle Timeout: No Sub Type Information |
GO to Pinpoint Test X |
| PCM |
P1595:00 |
Forced Engine Shutdown - Remote Start System Fault, Transmission Range Not In Park Position: No Sub Type Information |
GO to Pinpoint Test X |
| PDM |
B108F:23 |
Cabin Lock/Unlock Switch: Signal Stuck Low |
GO to Pinpoint Test G |
| PDM |
B1142:29 |
Ignition Status 1: Signal Invalid |
GO to Pinpoint Test Y |
| PDM |
B1142:86 |
Ignition Status 1: Signal Invalid |
GO to Pinpoint Test Y |
| PDM |
B12BA:11 |
Lock Status LED - Front: Circuit Short To Ground |
GO to Pinpoint Test H |
| PDM |
U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test AA |
| PDM |
U0164:00 |
Lost Communication With HVAC Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AC |
| PDM |
U0208:00 |
Lost Communication With Seat Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AD |
| PDM |
U0233:00 |
Lost Communication With Side Obstacle Detection Control Module 'B': No Sub Type Information |
GO to Pinpoint Test AF |
| PDM |
U0294:00 |
Lost Communication With Powertrain Control Monitor Module: No Sub Type Information |
GO to Pinpoint Test AG |
| PDM |
U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test AJ |
| PDM |
U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AK |
| PDM |
U211B:05 |
Control Module Message Authentication: System Programming Failure |
GO to Pinpoint Test AK |
| PDM |
U211B:08 |
Control Module Message Authentication: Bus Signal / Message Failure |
GO to Pinpoint Test AK |
| PDM |
U211B:43 |
Control Module Message Authentication: Special Memory Failure |
GO to Pinpoint Test AK |
| PDM |
U211B:51 |
Control Module Message Authentication: Not Programmed |
GO to Pinpoint Test AK |
| PDM |
U211B:81 |
Control Module Message Authentication: Invalid Serial Data Received |
GO to Pinpoint Test AK |
| PDM |
U211B:87 |
Control Module Message Authentication: Missing Message |
GO to Pinpoint Test AK |
| PDM |
U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test AK |
| PDM |
U3000:04 |
Control Module: System Internal Failure |
GO to Pinpoint Test AL |
| PDM |
U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AL |
| PDM |
U3000:4B |
Control Module: Over Temperature |
GO to Pinpoint Test AL |
| PDM |
U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test AH |
| PDM |
U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test AI |
| RTM |
U1A00:00 |
Private Communication Network: No Sub Type Information |
GO to Pinpoint Test V |