| C0020: 11 |
ABS Pump Motor Control: Circuit Short To Ground |
GO to Pinpoint Test H |
| C0020: 12 |
ABS Pump Motor Control: Circuit Short To Battery |
GO to Pinpoint Test H |
| C0020: 13 |
ABS Pump Motor Control: Circuit Open |
GO to Pinpoint Test H |
| C0020: 49 |
ABS Pump Motor Control: Internal Electronic Failure |
GO to Pinpoint Test H |
| C0020: 71 |
ABS Pump Motor Control: Actuator Stuck |
GO to Pinpoint Test H |
| C0030: 07 |
Left Front Tone Wheel: Mechanical Failures |
GO to Pinpoint Test AB |
| C0031: 01 |
Left Front Wheel Speed Sensor: General Electrical Failure |
GO to Pinpoint Test M |
| C0031: 07 |
Left Front Wheel Speed Sensor: Mechanical Failures |
GO to Pinpoint Test AB |
| C0031: 2F |
Left Front Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test AB |
| C0031: 4A |
Left Front Wheel Speed Sensor: Incorrect Component Installed |
GO to Pinpoint Test AL |
| C0031: 64 |
Left Front Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AB |
| C0033: 07 |
Right Front Tone Wheel: Mechanical Failures |
GO to Pinpoint Test AB |
| C0034: 01 |
Right Front Wheel Speed Sensor: General Electrical Failure |
GO to Pinpoint Test M |
| C0034: 07 |
Right Front Wheel Speed Sensor: Mechanical Failures |
GO to Pinpoint Test AB |
| C0034: 2F |
Right Front Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test AB |
| C0034: 4A |
Right Front Wheel Speed Sensor: Incorrect Component Installed |
GO to Pinpoint Test AL |
| C0034: 64 |
Right Front Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AB |
| C0036: 07 |
Left Rear Tone Wheel: Mechanical Failures |
GO to Pinpoint Test AB |
| C0037: 01 |
Left Rear Wheel Speed Sensor: General Electrical Failure |
GO to Pinpoint Test N |
| C0037: 07 |
Left Rear Wheel Speed Sensor: Mechanical Failures |
GO to Pinpoint Test AB |
| C0037: 2F |
Left Rear Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test AB |
| C0037: 4A |
Left Rear Wheel Speed Sensor: Incorrect Component Installed |
GO to Pinpoint Test AL |
| C0037: 64 |
Left Rear Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AB |
| C0039: 07 |
Right Rear Tone Wheel: Mechanical Failures |
GO to Pinpoint Test AB |
| C003A: 01 |
Right Rear Wheel Speed Sensor: General Electrical Failure |
GO to Pinpoint Test N |
| C003A: 07 |
Right Rear Wheel Speed Sensor: Mechanical Failures |
GO to Pinpoint Test AB |
| C003A: 2F |
Right Rear Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test AB |
| C003A: 4A |
Right Rear Wheel Speed Sensor: Incorrect Component Installed |
GO to Pinpoint Test AL |
| C003A: 64 |
Right Rear Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AB |
| C0040: 64 |
Brake Pedal Switch "A": Signal Plausibility Failure |
GO to Pinpoint Test AC |
| C0047: 1C |
Brake Booster Pressure Sensor: Circuit Voltage Out Of Range |
GO to Pinpoint Test CO |
| C0047: 64 |
Brake Booster Pressure Sensor: Signal Plausibility Failure |
GO to Pinpoint Test CO |
| C0049: 01 |
Brake Fluid Level: General Electrical Failure |
GO to Pinpoint Test I |
| C0049: 7A |
Brake Fluid Level: Fluid Leak Or Seal Failure |
GO to Pinpoint Test I |
| C0049: 7B |
Brake Fluid Level: Low Fluid Level |
GO to Pinpoint Test I |
| C0051: 64 |
Steering Wheel Position Sensor: Signal Plausibility Failure |
GO to Pinpoint Test LA |
| C0051: 67 |
Steering Wheel Position Sensor: Signal Incorrect After Event |
GO to Pinpoint Test LA |
| C0051: 85 |
Steering Wheel Position Sensor: Signal Above Allowable Range |
GO to Pinpoint Test LA |
| C0051: 86 |
Steering Wheel Position Sensor: Signal Invalid |
GO to Pinpoint Test LA |
| C0061: 28 |
Lateral Acceleration Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test AG |
| C0061: 54 |
Lateral Acceleration Sensor: Missing Calibration |
GO to Pinpoint Test AN |
| C0061: 64 |
Lateral Acceleration Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AG |
| C0062: 28 |
Longitudinal Acceleration Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test AG |
| C0062: 54 |
Longitudinal Acceleration Sensor: Missing Calibration |
GO to Pinpoint Test AN |
| C0062: 64 |
Longitudinal Acceleration Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AG |
| C0063: 28 |
Yaw Rate Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test AG |
| C0063: 64 |
Yaw Rate Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AG |
| C0064: 28 |
Roll Rate Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test AG |
| C0064: 64 |
Roll Rate Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AG |
| C006A: 95 |
Multi-axis Acceleration Sensor: Incorrect Assembly |
GO to Pinpoint Test AN |
| C006B: 00 |
Stability System Active Too Long: No Sub Type Information |
GO to Pinpoint Test AD |
| C0078: 00 |
Tire Diameter: No Sub Type Information |
GO to Pinpoint Test ZA |
| C052E: A2 |
ABS Pump Motor Control Circuit Low: System Voltage Low |
GO to Pinpoint Test H |
| C0594: 12 |
Brake Booster Motor "A" Performance: Circuit Short To Battery |
GO to Pinpoint Test CP |
| C0594: 78 |
Brake Booster Motor "A" Performance: Alignment Or Adjustment Incorrect |
GO to Pinpoint Test CP |
| C0594: 92 |
Brake Booster Motor "A" Performance: Performance Or Incorrect Operation |
GO to Pinpoint Test CP |
| C0596: 00 |
Brake Booster Motor "A" Current Sensor Circuit Range/Performance: No Sub Type Information |
GO to Pinpoint Test CP |
| C1013: 09 |
Brake System Pressure: Component Failures |
GO to Pinpoint Test CO |
| C1013: 7A |
Brake System Pressure: Fluid Leak Or Seal Failure |
GO to Pinpoint Test CO |
| C1013: 7C |
Brake System Pressure: Slow Response |
GO to Pinpoint Test CO |
| C1013: 92 |
Brake System Pressure: Performance Or Incorrect Operation |
GO to Pinpoint Test CO |
| C1018: 61 |
Regenerative Braking: Signal Calculation Failure |
GO to Pinpoint Test Z |
| C1019: 29 |
Linear Actuator Control (LAC): Signal Invalid |
GO to Pinpoint Test CO |
| C1019: 78 |
Linear Actuator Control (LAC): Alignment Or Adjustment Incorrect |
GO to Pinpoint Test CO |
| C1019: 92 |
Linear Actuator Control (LAC): Performance Or Incorrect Operation |
GO to Pinpoint Test CO |
| C101F: 46 |
Generic Valve Failure: Calibration/Parameter Memory Failure |
GO to Pinpoint Test Z |
| C101F: 49 |
Generic Valve Failure: Internal Electronic Failure |
GO to Pinpoint Test Z |
| C1020: 00 |
Brake System Fill Not Complete: No Sub Type Information |
GO to Pinpoint Test J |
| C1020: 52 |
Brake System Fill Not Complete: Not Activated |
GO to Pinpoint Test J |
| C1109: 64 |
Vehicle Dynamics Control Switch: Signal Plausibility Failure |
GO to Pinpoint Test O |
| C1A08: 1C |
Pressure Sensor Supply: Circuit Voltage Out Of Range |
GO to Pinpoint Test AM |
| C1B11: 71 |
Pressure Control Valve: Actuator Stuck |
GO to Pinpoint Test Y |
| P0562: 16 |
System Voltage Low: Circuit Voltage Below Threshold |
GO to Pinpoint Test A |
| P0563: 17 |
System Voltage High: Circuit Voltage Above Threshold |
GO to Pinpoint Test F |
| P05D3: 86 |
Driver Mode Select Switch "A" Range/Performance: Signal Invalid |
GO to Pinpoint Test OB |
| P1177: 64 |
Synchronization: Signal Plausibility Failure |
GO to Pinpoint Test Y |
| U0100: 00 |
Lost Communication With ECM/PCM "A": No Sub Type Information |
GO to Pinpoint Test AI |
| U0101: 00 |
Lost Communication with TCM: No Sub Type Information |
GO to Pinpoint Test AI |
| U0103: 00 |
Lost Communication With Gear Shift Control Module A: No Sub Type Information |
GO to Pinpoint Test AV |
| U011D: 00 |
Lost Communication With All Wheel Drive Control Module: No Sub Type Information |
GO to Pinpoint Test BX |
| U0122: 00 |
Lost Communication With Vehicle Dynamics Control Module: No Sub Type Information |
GO to Pinpoint Test BR |
| U0131: 00 |
Lost Communication With Power Steering Control Module "A": No Sub Type Information |
GO to Pinpoint Test AE |
| U0138: 00 |
Lost Communication with All Terrain Control Module: No Sub Type Information |
GO to Pinpoint Test BM |
| U0140: 00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test D |
| U0146: 00 |
Lost Communication With Serial Data Gateway "A": No Sub Type Information |
GO to Pinpoint Test BP |
| U0151: 00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test BH |
| U0155: 00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test AR |
| U0159: 00 |
Lost Communication With Parking Assist Control Module "A": No Sub Type Information |
GO to Pinpoint Test BY |
| U0232: 00 |
Lost Communication With Side Obstacle Detection Control Module "A": No Sub Type Information |
GO to Pinpoint Test BZ |
| U0233: 00 |
Lost Communication With Side Obstacle Detection Control Module "B": No Sub Type Information |
GO to Pinpoint Test BZ |
| U023A: 00 |
Lost Communication With Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test BQ |
| U023B: 00 |
Lost Communication With Image Processing Module B: No Sub Type Information |
GO to Pinpoint Test CK |
| U0256: 00 |
Lost Communication With Front Controls Interface Module "A": No Sub Type Information |
GO to Pinpoint Test AS |
| U0293: 00 |
Lost Communication with Hybrid/EV Powertrain Control Module: No Sub Type Information |
GO to Pinpoint Test CM |
| U0300: 51 |
Internal Control Module Software Incompatibility: Not Programmed |
GO to Pinpoint Test Z |
| U0401: 00 |
Invalid Data Received from ECM/PCM A: No Sub Type Information |
GO to Pinpoint Test AI |
| U0401: 86 |
Invalid Data Received from ECM/PCM A: Signal Invalid |
GO to Pinpoint Test AI |
| U0402: 00 |
Invalid Data Received from TCM: No Sub Type Information |
GO to Pinpoint Test AI |
| U0404: 00 |
Invalid Data Received from Gear Shift Control Module A: No Sub Type Information |
GO to Pinpoint Test AV |
| U041E: 00 |
Invalid Data Received From All Wheel Drive Control Module: No Sub Type Information |
GO to Pinpoint Test BX |
| U0420: 00 |
Invalid Data Received from Power Steering Control Module "A": No Sub Type Information |
GO to Pinpoint Test AE |
| U0422: 00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test D |
| U0439: 00 |
Invalid Data Received From All Terrain Control Module: No Sub Type Information |
GO to Pinpoint Test BM |
| U0452: 00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test BH |
| U0452: 86 |
Invalid Data Received From Restraints Control Module: Signal Invalid |
GO to Pinpoint Test BH |
| U053B: 00 |
Invalid Data Received From Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test BQ |
| U0557: 86 |
Invalid Data Received From Front Controls Interface Module "A": Signal Invalid |
GO to Pinpoint Test AS |
| U2001: 00 |
Reduced System Function: No Sub Type Information |
GO to Pinpoint Test C |
| U2017: 57 |
Control Module Software #2: Invalid/Incompatible Software Component |
GO to Pinpoint Test Z |
| U2017: 93 |
Control Module Software #2: No Operation |
GO to Pinpoint Test Z |
| U2018: 57 |
Control Module Software #3: Invalid/Incompatible Software Component |
GO to Pinpoint Test Z |
| U2024: 51 |
Control Module Cal-Config Data: Not Programmed |
GO to Pinpoint Test Z |
| U2100: 00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test Z |
| U2101: 00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test Z |
| U2107: 68 |
Collision Mitigation By Braking: Event Information |
GO to Pinpoint Test AQ |
| U2108: 68 |
Adaptive Cruise Control: Event Information |
GO to Pinpoint Test AQ |
| U2200: 00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test Z |
| U3000: 00 |
Control Module: No Sub Type Information |
GO to Pinpoint Test Y |
| U3000: 49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test Y |
| U3000: 4B |
Control Module: Over Temperature |
GO to Pinpoint Test Y |
| U3000: 96 |
Control Module: Component Internal Failure |
GO to Pinpoint Test Y |
| U3002: 62 |
Vehicle Identification Number: Signal Compare Failure |
GO to Pinpoint Test AF |
| U3003: 16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test A |
| U3003: 17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test F |
| U300A: 29 |
Ignition Switch: Signal Invalid |
GO to Pinpoint Test A |
| U3012: 68 |
Control Module Improper Wake-up Performance: Event Information |
GO to Pinpoint Test B |
| P0556: 00 |
Brake Booster Pressure Sensor Circuit Range/Performance: No Sub Type Information |
GO to Pinpoint Test CO |
| P0557: 00 |
Brake Booster Pressure Sensor Circuit Low: No Sub Type Information |
GO to Pinpoint Test CO |
| P05FF: 00 |
Brake Pressure Sensor / Brake Pedal Position Sensor Correlation: No Sub Type Information |
GO to Pinpoint Test CO |