| BCM |
B108A:01 |
Start Button: General Electrical Failure |
GO to Pinpoint Test A |
| BCM |
B108A:24 |
Start Button: Signal Stuck High |
GO to Pinpoint Test A |
| BCM |
B108A:9E |
Start Button: Stuck On |
GO to Pinpoint Test A |
| BCM |
B1142:29 |
Ignition Status 1: Signal Invalid |
GO to Pinpoint Test A |
| BCM |
B1240:11 |
Start Button Mode Indicator: Circuit Short to Ground |
GO to Pinpoint Test B |
| BCM |
B1240:15 |
Start Button Mode Indicator: Circuit Short to Battery or Open |
GO to Pinpoint Test C |
| BCM |
B1310:12 |
Run/Start Control: Circuit Short to Battery |
GO to Pinpoint Test A |
| BCM |
B1310:14 |
Run/Start Control: Circuit Short to Ground or Open |
GO to Pinpoint Test A |
| SCCM |
B112B:04 |
SCCM:Steering Wheel Module: System Internal Failure |
GO to Pinpoint Test I |
| SCCM |
B112B:44 |
SCCM:Steering Wheel Module: Data Memory Failure |
GO to Pinpoint Test I |
| SCCM |
B112B:45 |
SCCM:Steering Wheel Module: Program Memory Failure |
GO to Pinpoint Test I |
| SCCM |
B112B:46 |
SCCM:Steering Wheel Module: Calibration / Parameter Memory Failure |
GO to Pinpoint Test I |
| SCCM |
B112B:49 |
SCCM:Steering Wheel Module: Internal Electronic Failure |
GO to Pinpoint Test I |
| SCCM |
B135C:11 |
Heater Element:Circuit Short To Ground |
GO to Pinpoint Test G |
| SCCM |
B135C:13 |
Heater Element:Circuit Open |
GO to Pinpoint Test G |
| SCCM |
U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test H |
| SCCM |
U0140:00 |
SCCM:Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test J |
| SCCM |
U0146:00 |
SCCM:Lost Communication With Gateway "A": No Sub Type Information |
GO to Pinpoint Test J |
| SCCM |
U0146:87 |
SCCM:Lost Communication With Gateway "A": No Sub Type Information |
GO to Pinpoint Test J |
| SCCM |
U0155:00 |
SCCM:Lost Communication With Instrument Panel Cluster Module: No Sub Type Information |
GO to Pinpoint Test J |
| SCCM |
U01B7:00 |
Lost Communication With Switch Input Module "A": No Sub Type Information |
GO to Pinpoint Test M |
| SCCM |
U023A:00 |
SCCM:Lost Communication With Image Processing Module "A": No Sub Type Information |
GO to Pinpoint Test J |
| SCCM |
U0241:00 |
SCCM:Lost Communication With Headlamp Control Module: No Sub Type Information |
GO to Pinpoint Test J |
| SCCM |
U210A:11 |
Temperature Sensor:Circuit Short To Ground |
GO to Pinpoint Test G |
| SCCM |
U210A:13 |
Temperature Sensor:Circuit Open |
GO to Pinpoint Test G |
| SCCM |
U3003:A2 |
Battery Voltage: System Voltage Low |
GO to Pinpoint Test E |
| SCCM |
U3003:A3 |
Battery Voltage:System Voltage High |
GO to Pinpoint Test F |
| SECM |
B135C:11 |
Heater Element:Circuit Short To Ground |
GO to Pinpoint Test K |
| SECM |
B135C:15 |
Heater Element:Circuit Short to Battery or Open |
GO to Pinpoint Test K |
| SECM |
B13BD:92 |
Steering Wheel Heater Module:Performance or Incorrect Operation |
GO to Pinpoint Test K |
| SECM |
U1000:00 |
Solid State Driver Protection Active:No Sub Type Information |
GO to Pinpoint Test K |
| SECM |
U210A:02 |
Temperature Sensor:General Signal Failure |
GO to Pinpoint Test K |
| SECM |
U210A:11 |
Temperature Sensor:Circuit Short to Ground |
GO to Pinpoint Test K |
| SECM |
U210A:15 |
Temperature Sensor:Circuit Short to Battery or Open |
GO to Pinpoint Test K |
| SIMA |
U0100:00 |
Lost Communication With ECM/PCM "A": No Sub Type Information |
GO to Pinpoint Test L |
| SIMA |
U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test L |
| SIMA |
U3003:16 |
Battery Voltage:Battery Voltage Below Threshold |
GO to Pinpoint Test N |
| SIMA |
U3003:17 |
Battery Voltage:Battery Voltage Above Threshold |
GO to Pinpoint Test O |