Steering Wheel And Column Electrical Components DTCS
Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| B108A:01 | Start Button: General Electrical Failure | GO to Pinpoint Test A |
| B108A:24 | Start Button: Signal Stuck High | GO to Pinpoint Test A |
| B1142:29 | Ignition Status 1: Signal Invalid | GO to Pinpoint Test A |
| B1240:11 | Start Button Mode Indicator: Circuit Short to Ground | GO to Pinpoint Test B |
| B1240:15 | Start Button Mode Indicator: Circuit Short to Battery or Open | GO to Pinpoint Test C |
| B1310:12 | Run/Start Control: Circuit Short to Battery | GO to Pinpoint Test A |
| B1310:14 | Run/Start Control: Circuit Short to Ground or Open | GO to Pinpoint Test A |
| B112B:04 | SCCM:Steering Wheel Module: System Internal Failure | GO to Pinpoint Test I |
| B112B:44 | SCCM:Steering Wheel Module: Data Memory Failure | GO to Pinpoint Test I |
| B112B:45 | SCCM:Steering Wheel Module: Program Memory Failure | GO to Pinpoint Test I |
| B112B:46 | SCCM:Steering Wheel Module: Calibration / Parameter Memory Failure | GO to Pinpoint Test I |
| B112B:49 | SCCM:Steering Wheel Module: Internal Electronic Failure | GO to Pinpoint Test I |
| B135C:11 | Heater Element:Circuit Short To Ground | GO to Pinpoint Test G |
| B135C:13 | Heater Element:Circuit Open | GO to Pinpoint Test G |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test H |
| U0140:00 | SCCM:Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test J |
| U0146:00 | SCCM:Lost Communication With Gateway "A": No Sub Type Information | GO to Pinpoint Test J |
| U0146:87 | SCCM:Lost Communication With Gateway "A": No Sub Type Information | GO to Pinpoint Test J |
| U0155:00 | SCCM:Lost Communication With Instrument Panel Cluster Module: No Sub Type Information | GO to Pinpoint Test J |
| U023A:00 | SCCM:Lost Communication With Image Processing Module "A": No Sub Type Information | GO to Pinpoint Test J |
| U0241:00 | SCCM:Lost Communication With Headlamp Control Module: No Sub Type Information | GO to Pinpoint Test J |
| U210A:11 | Temperature Sensor:Circuit Short To Ground | GO to Pinpoint Test G |
| U210A:13 | Temperature Sensor:Circuit Open | GO to Pinpoint Test G |
| U3003:A2 | Battery Voltage: System Voltage Low | GO to Pinpoint Test E |
| U3003:A3 | Battery Voltage:System Voltage High | GO to Pinpoint Test F |
| B135C:11 | Heater Element:Circuit Short To Ground | GO to Pinpoint Test K |
| B135C:15 | Heater Element:Circuit Short to Battery or Open | GO to Pinpoint Test K |
| B13BD:92 | Steering Wheel Heater Module:Performance or Incorrect Operation | GO to Pinpoint Test K |
| U1000:00 | Solid State Driver Protection Active:No Sub Type Information | GO to Pinpoint Test K |
| U210A:02 | Temperature Sensor:General Signal Failure | GO to Pinpoint Test K |
| U210A:11 | Temperature Sensor:Circuit Short to Ground | GO to Pinpoint Test K |
| U210A:15 | Temperature Sensor:Circuit Short to Battery or Open | GO to Pinpoint Test K |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test L |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test L |
| U3003:16 | Battery Voltage:Battery Voltage Below Threshold | GO to Pinpoint Test M |
| U3003:17 | Battery Voltage:Battery Voltage Above Threshold | GO to Pinpoint Test N |